Tube Parts

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This spigot routes water from the internal supply to the dispenser outlet, delivering a controlled stream. Replacing a cracked or worn spigot helps restore proper dispensing and reduces drips or leaks at the dispenser area.

• Directs water from the internal tubing/reservoir to the dispenser outlet
• Maintains a defined flow path to help prevent splashing and after-drip
• Common symptoms of failure: dripping at the dispenser, slow/erratic flow, leaks inside the door, or visible cracks at the outlet
• Replace if damaged, leaking, or obstructed by mineral buildup

• Unplug the appliance and shut off the household water supply
• Dispense water to relieve line pressure before replacement
• Access the dispenser; note tubing orientation and fully seat/secure connections
• Restore water and power; flush the system and check all joints for leaks

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.

This drain hose carries wastewater from the washer's drain pump to your home standpipe or sink, ensuring proper draining and helping prevent leaks or backflow. Replace a cracked, kinked, or clogged hose to restore reliable draining.

• Provides a sealed path for wastewater from the drain pump to the household drain
• A damaged or clogged hose can cause leaks, slow draining, or drain-related error codes
• Kinks, splits, or pinholes may allow water to escape during drain cycles
• Loose or worn hose ends can lead to drips at the pump or rear connection

• Disconnect power and water supply; pull the appliance forward to access the hose
• Expect residual water—use towels or a shallow pan and clamp off the old hose if needed
• Note hose routing and clamp locations; reuse existing clamps and secure connections firmly
• Route the new hose without kinks and set the discharge height per your installation guide to prevent siphoning

This washer drain hose carries used water from the tub to your home drain. Replacing a cracked, clogged, or kinked hose helps restore proper draining and prevents leaks during the drain/spin portion of the cycle.

• Routes wastewater from the washer to the household standpipe or laundry sink
• Damage or blockage can cause leaks, slow or no draining, or water on the floor
• Replace if you see cracks, splits, bulges, or persistent leaking at the back of the washer
• A pinched or flattened hose can also lead to standing water after a cycle

• Unplug the washer and turn off water; place towels or a pan to catch residual water
• Note the routing; loosen clamps and remove the old hose from the washer outlet and drain connection
• Install the new hose and secure with clamps; avoid kinks or sharp bends
• Verify correct drain height/air gap to prevent siphoning, then run a drain/spin to check for leaks

This fill and drain hose assembly connects a portable dishwasher to a sink faucet, delivering incoming water and routing wastewater back to the sink. Replacing a worn assembly restores a secure connection and helps prevent leaks during operation.

• Integrates inlet and drain hoses with a faucet coupler for quick, tool-free hookup
• Supplies water to the dishwasher and returns drain water to the sink
• Can address no fill or no drain symptoms caused by a damaged or obstructed hose/coupler

• Safety first: Unplug the dishwasher and turn off water before servicing
• Expect residual water; place towels/pan and relieve line pressure
• Ensure a compatible faucet adapter is installed; attach the coupler fully and verify a good seal
• Route hoses without kinks, secure the drain end to the sink, and check for leaks on first run

This replacement hose routes water within your washer. Replacing a cracked, worn, or leaking hose restores a secure, watertight path so the machine can move water properly without puddles or performance issues.

• Transfers water between internal components during wash cycles
• Maintains a sealed flow path to help prevent leaks
• Damage may present as water on the floor, moisture under the unit, or related fill/drain errors
• Cracks, swelling, abrasion, or loose connections are common failure signs

• Unplug the washer and turn off water supply; have towels or a pan ready for residual water
• Note hose routing and clamp positions before removal; photos can help
• Transfer or replace clamps as needed; seat connections fully and secure firmly
• Run a test cycle and check all connections for leaks

This is a replacement ice maker fill tube. This is a genuine OEM part made by LG and has been sourced directly from the manufacturer. This part is intended to replace broken or detached ice maker fill tubes in a variety of refrigerators. This piece of plastic tubing supplies the in-built refrigerator ice maker with water so it can make ice. If the ice maker is not working properly and is not making ice, there may be an issue with the tubing. Always make sure that the refrigerator is entirely disconnected from power and water before starting the any repair work. Please ensure that the appropriate safety precautions are followed when attempting to fix any appliances. For more accurate information on how and where to install this ice maker fill tube, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this ice maker fill tube is suitable for use on several different models of refrigerators manufactured by LG and Kenmore. This is a genuine part made of high-quality, durable plastic and is sold individually.

This water fill extension tube assembly directs water into the ice maker's fill cup, providing a clear path for each cycle and helping reduce leaks or ice buildup caused by a cracked, misrouted, or blocked tube.

• Routes water from the inlet toward the ice maker fill cup
• Maintains a clear, controlled water path to help minimize drips and spray in the freezer
• Replaces cracked, kinked, or frozen fill tubes that can disrupt ice production
• Typical symptoms: ice maker not filling, water dripping/pooling in the freezer, or ice/frost around the fill area

• Disconnect power and turn off the household water supply before service
• Access the fill tube at the freezer/ice maker area; thaw any ice with warm air—avoid sharp tools or excessive heat
• Match the original routing and insertion depth; seat the tube fully in the fill cup/channel
• Restore water and power, then run a fill cycle and check for leaks

This water inlet tube routes incoming water inside the refrigerator, restoring a secure, leak-resistant path for the ice/water system. Replacing a damaged tube helps prevent leaks and ensures proper filling where the system needs it. What it does:

• Carries water from the supply/valve to the internal fill point
• Replaces tubing that is cracked, kinked, brittle, or leaking
• Helps resolve water drips at the rear or around the fill area
• Clears the path so blockages don't reduce or stop filling/ice production

• 1 water inlet tube

• Disconnect power and shut off the water supply before servicing
• Pull the refrigerator forward carefully for rear access and protect the floor
• Match the original routing; transfer any model-specific clips or seals if present
• Restore water, purge air, and check all connections thoroughly for leaks

This water tube connector joins sections of your refrigerator's water line for the dispenser and ice maker. It restores a secure, leak-resistant connection when the original coupling is damaged or leaking.

• Connects two segments of refrigerator water tubing
• Helps maintain proper water flow to dispenser and ice maker
• Resolves leaks caused by a cracked, worn, or loose connector
• Useful when replacing or rerouting water lines during service

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure
• Cut tubing square and insert fully until seated; tug gently to confirm a secure fit
• Restore water and check all connections for leaks; replace any damaged tubing as needed

This flume hose kit replaces the flexible hose that routes water from the dispenser/fill flume into the washer tub. Restoring a tight, unobstructed hose helps prevent leaks and ensures detergents, bleach, and softener are carried into the wash.

• Directs fill/dispenser water from the flume to the tub during wash and rinse
• Restores proper flow so dispenser compartments empty correctly
• Helps prevent leaks caused by splits, brittleness, or loose connections
• Typical symptoms: water on the floor, dispenser not draining, weak flow into tub, musty odor near dispenser

• Disconnect power and shut off water supply before servicing
• Access the dispenser/flume area by removing the top or control panel per your model
• Note hose routing; transfer and secure clamps; avoid kinks and rub points
• Run a quick fill/rinse to check for leaks at both connections after installation

This inlet hose channels household water to the appliance's fill system. Replacing a worn or leaking hose restores proper water flow and helps protect floors and internal components from water damage.

• Directs water from the household supply to the unit's inlet/fill assembly
• Maintains a watertight path to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or mineral-fouled
• Common symptoms: leaks at fittings or beneath the unit, slow or no fill, intermittent filling, or water-related error messages

• Disconnect power and turn off the water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure slowly
• Route the hose without kinks; ensure sealing surfaces and/or washers are clean and properly seated
• Secure connections per the OEM design (compression fitting or clamp); restore water and check carefully for leaks on the first run

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle

This is the flexible drain hose that carries used water from the washer's pump to the household drain. Replacing a cracked or kinked hose helps prevent leaks and restores proper draining performance.

• Routes discharge water from the drain pump to the standpipe or laundry sink
• Leaks, cracks, bulges, or kinks can cause water on the floor or slow/no draining
• Loose connections at the hose ends may lead to intermittent leaks
• A collapsed or internally blocked hose can trigger drain errors or extended drain times

• Unplug the washer and turn off water; have towels or a pan ready for residual water
• Access the pump and hose; note routing before removal
• Transfer clamps and fittings from the old hose if required; ensure secure, leak-free connections
• Route the hose without sharp bends;

This collar kit renews the quick-connect faucet interface on select portable appliances, restoring a secure, leak-resistant connection at the sink. Replace a stripped, cracked, or missing collar to stop drips and ensure the coupler attaches smoothly.

• Provides the correct shoulder/threads for the quick-connect coupler or adapter
• Helps seal the faucet connection to reduce leaks and spray
• Replaces worn, damaged, or missing collar in the connector assembly
• Common symptoms: leaking at the faucet, coupler won't latch or pops off, loose connection

• Turn off water and disconnect the appliance from the faucet before service
• Relieve hose pressure and place a towel under the work area
• Remove the existing collar and clean faucet threads before installing the new one
• Hand-tighten only; avoid overtightening and check for leaks on first use