Machine Ptc Parts

PTC relay is a start device that helps the appliance motor begin turning by providing a brief boost to the start winding. Replacing a faulty relay restores reliable motor starting and can return normal operation. What it does:

• Provides a temporary start assist to the motor's start winding so the motor can overcome initial inertia.
• Commonly replaced when the motor hums but won't start or when the unit fails to begin operation.
• Can address symptoms such as clicking noises at startup, intermittent motor starting, or no motor movement despite power.
• Works as the motor start control — failure can prevent the appliance from operating properly.

• Disconnect power before servicing to avoid electric shock.
• Note terminal locations and orientation before removal; install replacement on the same terminals.
• Handle terminals gently and ensure tight, corrosion-free connections.
• After installation, restore power and verify the motor starts and runs normally.

This water level pressure switch senses the tub's water level via air pressure and signals the control to stop filling at the correct point, helping the cycle advance properly and guarding against overfilling.

• Monitors water level through the pressure hose and reports to the control
• Shuts off inlet valves when the target level is reached
• Allows the cycle to proceed and spin only when the tub is sensed empty
• Common symptoms of a failed switch include overfilling or underfilling, long fill, stopping during fill, not advancing, or water-level error codes

• Disconnect power and turn off water supplies before servicing
• Access the console/control area; move the wire harness and pressure hose to the new switch and secure it in place
• Inspect the pressure hose for kinks, cracks, or moisture; clear or replace if damaged to ensure accurate sensing
• Ensure an airtight hose connection, then run a test fill to verify proper shutoff and operation

Mounted behind the dryer's control panel button, this push-button switch closes the circuit when pressed. Replacing a worn or unresponsive switch restores crisp, reliable button action so the selected function engages consistently.

• Completes the electrical circuit when the panel button is pressed
• Helps address no response to the button, intermittent activation, or a button that sticks or feels loose
• Failed switches may show heat discoloration or burned/corroded terminals

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the rear of the control panel to reach the switch
• Photograph/label wire positions and transfer one at a time; avoid pulling on wires
• Seat and secure the switch, reassemble, and test operation before finalizing

This rotary on/off switch controls the dryer's Finish Guard (also called Wrinkle Guard/Wrinkle Shield) feature. Replacing it restores proper control of the post-cycle intermittent tumbling that helps reduce wrinkles, preventing the feature from being stuck on or off.

• Provides 2-position on/off selection for the Finish Guard/Wrinkle Guard function
• Failure can cause the feature not to engage or to stay on after the cycle ends
• Knob may feel loose or fail to click when the switch is worn
• Mounts in the control console and interfaces with the external selector knob

• Disconnect power before servicing
• Access through the control console; remove paneling as needed
• Transfer wires one at a time or photograph connections for reference
• Reinstall using the existing knob and mounting hardware

Replacement infinite switch that restores variable heat control for a surface heating element on an electric range, letting you adjust burner temperature smoothly and accurately. What it does:

• Regulates power to a surface heating element so the burner produces the selected heat level.
• Replaces a failed or worn rotary control that no longer changes element output.
• Common symptoms: burner won't heat, only heats at one setting, temperature jumps or fluctuates, or knob turns with no effect.
• Fits behind the console and connects to existing element wiring and control knob.

• Disconnect the appliance power before removing the console or control panel to avoid electrical shock.
• Confirm wire locations and take a photo before disconnecting to ensure correct reconnection.
• Secure the switch in place and reconnect wires firmly; test all settings after reassembly.

This replacement switch assembly restores the appliance's electrical switching function so the control or safety circuit can open and close when activated. Use it to replace a worn or failed switch and regain expected control response. What it does:

• Acts as the electrical contact that opens or closes a circuit when toggled or pressed
• Commonly used where a user action or door/lid position must be sensed by the control
• Can address symptoms such as no start, unresponsive controls, or intermittent operation tied to the switch circuit
• Transfers the mechanical action to the appliance's control or safety system

What's included: One switch assembly Install notes:

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Verify correct wiring and connector orientation before reassembly; take photos if needed
• Test switch continuity (with power off) after installation to confirm correct operation

A thermal overload protector that helps prevent motor damage by cutting power if the dryer motor overheats. Fits the motor assembly and restores normal operation once the motor cools. What it does:

• Detects excessive motor temperature and interrupts power to prevent motor burnout
• Helps stop the motor from running when overheating occurs
• Commonly replaced when the dryer won't start or the motor hums but does not turn
• Can prevent further electrical damage by opening the circuit during thermal faults

• One thermal overload protector

• Disconnect power to the appliance before servicing to avoid shock or injury
• Located on or near the dryer motor; note wire locations or take a photo before removal
• Replace with the correct PN and secure terminals firmly; do not force connections
• Check motor bearings, start components, and wiring if symptoms continue after replacement

A replacement motor start/run capacitor that helps restore reliable motor starting and smooth operation for compressors and fans. Installing the correct capacitor can reduce hard-starts, humming and intermittent motor operation. What it does:

• Provides the temporary boost motors need to start and stabilize while running.
• Helps compressors and fan motors start more easily and run more efficiently.
• Commonly associated with symptoms like humming, motors that won't start, intermittent operation, or reduced cooling performance.
• Prevents repeated motor stress that can lead to overload trips or premature motor wear.

• Disconnect power to the appliance before accessing electrical components.
• Discharge the capacitor and tag/photograph wire locations before removal to ensure correct reinstallation.
• Replace with the exact OEM part or an approved equivalent; do not bend or puncture the capacitor can.

A film radial capacitor used in appliance electrical assemblies to stabilize voltage and support motor and control circuits. Replaces a worn or failed film capacitor to restore consistent operation and reduce electrical noise. What it does:

• Smooths and stabilizes voltage in motor and control circuits to help maintain reliable operation
• Reduces electrical noise that can cause humming or erratic behavior in appliances
• Helps ensure consistent motor start/run performance when the capacitor is the cause of symptoms
• Commonly replaced when appliances exhibit intermittent starts, humming, or control board errors linked to compromised capacitors

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor safely before touching terminals to avoid shock
• Observe correct polarity/terminal orientation and secure connections per OEM guidance

This run capacitor helps the refrigerator compressor start and run smoothly, restoring normal operation when a weak or failed capacitor causes the compressor to struggle. Replacing a faulty capacitor can reduce humming and improve cooling performance. What it does:

• Provides continuous phase-shift to the compressor motor for stable running.
• Helps maintain proper compressor speed and efficiency during operation.
• Commonly replaced when the compressor hums, won't stay running, or cooling is inconsistent.
• Reduces risk of repeated motor cycling caused by a weak or open capacitor.

• Always disconnect power to the appliance before accessing electrical components.
• Discharge the capacitor before handling; capacitors can hold a charge even when powered off.
• Observe terminal orientation and mounting location; replace with the same type and ratings.

This 3-position temperature switch selects the dryer's heat level so the appliance reaches the desired drying temperature. It replaces a worn or faulty selector to restore proper temperature selection and consistent drying performance. What it does:

• Switches between three temperature settings to control dryer heat levels.
• Routes power to the heater circuit based on the selected heat setting.
• Commonly replaces a switch that causes incorrect heat, no heat on some settings, or inability to change temperature.
• Works with the dryer's control system and thermostats to maintain selected drying temperature.

• Disconnect power to the appliance before attempting any service.
• Handle terminals and connectors carefully; match wiring to original locations or take a photo before removal.
• Verify operation with a multimeter for continuity per service manual before and after installation.

The Lid Switch is an OEM part for Frigidaire washing machines. It is an electronic component located within the washer lid that functions to detect when the lid is opened or closed. The lid switch communicates this information to the control unit to allow or pause the operation of the washer accordingly.

Causes of a bad lid switch can include wear and tear of sensitive electrical contacts over time, exposure to moisture or debris that disrupts connections, or accidental physical damage to the switch mechanism.

Symptoms of a bad lid switch include:

• The washer fails to start or run when the lid is closed   
• Inability to pause the cycle when the lid is opened
• Fault codes or error messages related to lid position detection

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This cord set is a direct-replacement power cord that restores electrical connection to the appliance, letting it receive safe, consistent power when the original cord is damaged or worn. What it does:

• Provides the appliance's main AC connection so it can power on and operate
• Replaces frayed, cut, or melted cords that cause intermittent power or arcing
• Prevents unsafe wiring conditions from exposed conductors or loose connections
• Restores a secure plug/cable interface when the cord or plug is damaged

• One replacement cord set

• Always disconnect power at the breaker or unplug the appliance before replacing the cord
• Verify the replacement cord matches the original in wire count, connector type, and amp rating
• Tighten terminal screws securely and route the cord to avoid pinching or contact with hot components

This lid switch assembly detects when the washer lid is closed and lets the machine start and complete cycles. Replacing a failed switch restores the washer's safety interlock and helps resolve start/spin problems. What it does:

• Detects lid closure to enable motor and spin cycles
• Prevents the washer from starting or spinning when the lid is open
• Common replacement for washers that won't start, won't spin, or stop mid-cycle
• Completes the electrical safety/interlock circuit for proper operation

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access may require removing the top or rear access panel; keep track of fasteners and wire locations
• Disconnect wiring harness and replace the switch assembly; ensure secure mounting and correct connector seating

This refrigerator compressor start device provides the initial boost the compressor needs to start, then disengages. Replacing a failed start device helps restore reliable compressor startup and steady cooling performance.

• Supplies momentary power to the compressor's start winding to get the motor running
• Disengages after startup so the compressor can run normally
• Typical failure symptoms: refrigerator warm or not cooling, compressor won't start, rapid clicking from the compressor area, or intermittent cooling
• Located on the side of the compressor at the back of the appliance

• Unplug the refrigerator and allow the compressor area to cool before servicing
• Access the compressor at the rear; note wire positions and the device orientation
• Pull the old device straight off the compressor pins; seat the new device fully and reconnect wires securely
• If your model uses a separate run capacitor, transfer and reconnect it exactly as originally configured

This temperature switch is a replacement thermal control that helps the appliance regulate and maintain correct operating temperature for safe, reliable performance. Replaces a worn or faulty switch to restore proper temperature response. What it does:

• Opens or closes the circuit based on temperature to control heating elements or cycles
• Restores normal temperature regulation when oven, range, or heating function is inconsistent
• Can prevent overheating or underheating symptoms like uneven cooking or long heat-up times
• Works as a direct electrical control

• Disconnect power to the appliance before starting any repair
• Handle terminals carefully; ensure secure, corrosion-free electrical connections