Ptc Parts

This electric pressure switch senses pressure changes and sends a signal to the appliance control, restoring reliable pressure detection and normal operation. Use it when the machine fails to detect pressure or shows pressure-related errors. What it does:

• Detects changes in air/water pressure and converts them to an electrical signal for the control board
• Helps the appliance recognize correct fill, drain, or airflow conditions
• Commonly linked to symptoms such as failure to start, not filling, running continuously, or pressure-related error codes
• Replaces a failed or intermittent pressure-sensing component to restore expected cycling behavior

• Disconnect power before attempting any service to avoid shock or damage
• Label and photograph wiring before removal to ensure correct reconnection
• Test with a multimeter if troubleshooting

This relay assembly helps start the refrigerator compressor so the cooling system can run reliably. It replaces a worn or failed start relay to restore normal compressor startup and reduce hard-start symptoms. What it does:

• Provides the initial start pulse to the compressor motor so the refrigeration cycle can begin
• Stops excessive current draw during startup to protect the compressor
• Commonly used when the compressor hums, won't start, or cycles on and off rapidly
• Helps eliminate starter-related clicking or failure-to-start issues

• Disconnect power to the appliance before inspecting or replacing the relay
• Handle electrical connectors carefully; ensure secure, correct reattachment
• Verify match to the existing relay and mounting before installation

This tub displacement switch monitors water level/pressure to help the washer detect tub fill and balance, reducing overfill and load sensing errors. It replaces a worn or faulty unit to restore reliable fill and balance sensing. What it does:

• Senses tub water displacement/pressure changes so the washer can detect correct fill and load balance
• Helps prevent overfilling and supports proper spin cycles by reporting tub condition to the control
• Commonly replaced when washer overfills, won't start spin, or shows erratic fill behavior

• Disconnect power before accessing internal components to avoid shock
• Mounts to the washer chassis with electrical connector and vacuum/pressure hose; reuse existing hose if undamaged
• Verify hose and fittings are intact and free of blockages before installation

This electrical wire harness connects key components to deliver power and signal paths so your appliance controls and features operate reliably. It replaces a damaged or worn harness to restore proper electrical connectivity. What it does:

• Routes power and signal between control board, sensors, and accessories
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps resolve symptoms like lights, fans, or controls not powering on or working erratically
• Maintains proper connector fit and wiring color-coding for correct hookups

• One electrical wire harness

• Disconnect power before inspecting or replacing the harness to avoid shock
• Confirm connector orientation and secure all clips; route wiring away from heat and moving parts
• Inspect mating connectors for damage and replace if corroded or burned

This plug-style electrical switch controls power to a specific appliance circuit, restoring proper on/off function for the related component. It's a small, direct-replacement switch used where a plug-in connection is required. What it does:

• Controls electrical power flow to the connected component so the part can be turned on or off.
• Can resolve symptoms like loss of power to a specific function or intermittent operation of that circuit.
• Acts as the user- or board-operated electrical connection point for the appliance subassembly.
• Provides a removable plug-style connection for easier replacement or servicing.

• One plug-style electrical switch

• Disconnect power to the appliance before servicing to avoid shock risk.
• Confirm the correct orientation and secure connection of plug terminals during install.
• Tighten mounting fasteners as required; avoid overtightening plastic housings.

This overload protector is a safety device that helps prevent compressor damage by stopping electrical current during overheating or locked-rotor conditions. It's a direct-fit replacement that restores proper compressor protection and helps keep the appliance running safely. What it does:

• Protects the compressor by interrupting power if the motor overheats or experiences an electrical fault
• Common symptom: refrigerator runs but compressor won't start or only hums
• Common symptom: fridge cycles frequently or doesn't maintain temperature due to compressor protection tripping
• Works with the start device to help ensure reliable compressor startup

• Disconnect power before servicing; work only with the appliance unplugged
• Access typically requires removing the rear access panel to reach the compressor area
• Replace using the same mounting and terminal connections; ensure secure electrical connections

This selector switch is the console control that lets you choose washer options. It routes power to the appropriate circuit so the setting you pick—such as temperature or speed—engages reliably during the cycle.

• Interfaces with the control knob to communicate user-selected options to the washer's control
• Common fix when options won't change or only one setting works
• Helps resolve intermittent response or dead spots when turning the selector
• Restores consistent operation of user-selected wash features

• Disconnect power to the appliance before servicing
• Access the control console; remove the rear cover or screws as required
• Note wire positions and transfer connectors to the new switch one at a time
• Secure the switch, reinstall the knob/panel, and test each selection

This Smart ATC temperature switch senses and helps regulate oven temperature for more consistent cooking. It replaces a failed switch to restore correct temperature feedback to the range control for accurate heating. What it does:

• Detects oven temperature and sends a signal to the control so heating elements cycle appropriately
• Helps correct issues where the oven runs too hot, too cold, or cycles erratically
• Works as part of the temperature control system—does not include the main control board
• Replaces a worn or failed temperature/A.T.C. sensor switch to restore proper temperature sensing

• One temperature switch (Smart ATC)

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access typically requires removing the oven control panel or back panel; keep track of screws and wire connections
• Handle the switch and connector gently to avoid damage; verify wiring matches original before reconnecting

This pressure switch senses pressure changes and signals the appliance control to start or stop functions, helping restore proper operation when pressure-based controls fail. It's a direct-replacement style switch used in compatible Frigidaire appliances. What it does:

• Detects and closes or opens an electrical circuit based on air or water pressure changes
• Signals the control board to advance cycles or enable components (pump, valve, blower)
• Common symptom indicator: appliance won't complete cycles or responds inconsistently when pressure-controlled
• Helps stop operation when pressure limits are reached to protect system components

• One pressure switch

• Disconnect power (and water, if applicable) before starting work
• Handle the switch and its terminals with care; avoid bending pins or cracking the housing
• Inspect and replace any associated tubing or fittings that are cracked or clogged

This 120V replacement power cord restores household current to gas ranges and ovens that use a corded connection for clocks, lights, igniters and controls. It provides a straightforward way to replace a damaged or worn cord and regain safe power to the appliance. What it does

• Supplies 120-volt power from the wall outlet to the range/oven's control system, clock and lights.
• Restores ignition and control functions when a frayed or broken cord prevents the appliance from receiving power.
• Replaces cords that show signs of burning, cracking, loose connections, or exposed wiring.
• Reduces risk of electrical faults caused by damaged insulation or terminals.

• One 120V power cord

• Disconnect power at the circuit breaker or unplug the appliance before starting; ensure the appliance is de-energized.
• Route and secure the cord to avoid pinching; tighten terminal screws to manufacturer torque recommendations.

This starter relay helps start the refrigerator compressor so the unit can cool properly. It replaces a worn or failed relay to restore reliable compressor start-up and reduce repeated clicking or humming. What it does:

• Provides the initial kick to start the compressor motor
• Stops the compressor from stalling during startup
• Commonly used when the fridge hums but doesn't cool or the compressor only clicks on and off
• Helps prevent extended run attempts that can overload the compressor

• One starter relay

• Disconnect power to the appliance before servicing
• Replace only when unit is fully powered down and components are cool to the touch
• Inspect the compressor terminal area for damage or corrosion and clean before installing

This PTC starter helps the compressor start by briefly supplying the correct current at startup, restoring reliable cooling when the compressor struggles to kick on. Compact replacement for failed or weak start devices. What it does

• Provides a timed boost to the compressor start winding so the compressor can start reliably
• Commonly used when a refrigerator or freezer won't start or hums without running
• Helps prevent frequent hard starts that can overheat the compressor
• Passive solid-state design with no moving parts for simple, maintenance-free operation

• Disconnect power to the appliance before inspecting or replacing the starter
• Handle electrical connections carefully; install the starter in the same orientation and wiring position as the original
• If the compressor or start relay shows additional damage, replace those components.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This start device helps the appliance motor get up to speed so the unit starts and runs reliably. It's a direct-fit replacement that restores proper starting operation when the motor hesitates or won't start. What it does:

• Provides the initial boost or timing signal the motor needs to start turning
• Commonly replaces a failed start component when the motor hums but won't begin running
• Helps stop repeated start attempts that can overload the motor or trip protection
• Works as part of the motor starting circuit to ensure smooth startup

• Disconnect power to the appliance before attempting any repair to avoid shock or injury
• Handle the part carefully and match connectors/terminals to the original during replacement
• Basic hand tools are typically required; keep track of screws and wire routing