Thermal Coupler Parts

This factory support stabilizes and positions its mating assembly so it stays secure and aligned during use. Replacing a worn or broken support helps restore proper fit and prevents looseness or shifting that can affect performance. What it does

• Provides structural support and correct positioning for the related assembly
• Helps prevent wobble, sagging, rattling, or misalignment
• Typical failure signs: visible cracks, broken/missing tabs, or a loose fit
• Can help resolve components not staying in place or moving unexpectedly

• 1 support

• Disconnect power to the appliance before servicing
• Access the support location and note the original orientation
• Transfer and reuse any original mounting hardware your model uses
• Seat the new support fully and verify a secure fit before restoring power

The Thermistor Inlet is an OEM part for GE dryers. As a temperature monitoring device, it senses air inlet temperatures entering the dryer drum each cycle. This thermistor provides feedback to regulating components like the control board and heating elements.

Symptoms of a faulty thermistor inlet include:  

• Unexpected fluctuation of inlet air temperatures
• Issues activating or deactivating heating elements as needed  
• Potential safety trips from inaccurate temperature readings
• Improper or inconsistent drying times

Causes of a bad thermistor can be normal wear over repeated uses and heat cycles. Mineral scale buildup may also impact sensor accuracy over time. Electrical faults could potentially disrupt functioning.

This OEM GE replacement ensures proper inlet temperature sensing once installed. Compatible with some Hotpoint, RCA, and Kenmore dryers as well, it maintains safe, consistent performance through accurate temperature feedback to dryer electronics.

Kit contains 2 brackets and 4 screws. Used for granite and corning

Color: gray. Measures about 3 inches in diameter.

This fixed thermostat protects the appliance by opening the circuit when excessive heat is detected. Replacing a failed or weak thermostat restores reliable over-temperature protection and helps prevent heat-related shutdowns.

• Opens the circuit if the protected area overheats to help prevent damage to components
• Helps with symptoms like unexpected shutdowns during operation or no power after overheating
• Can be the cause when the unit only runs again after cooling down
• Helps maintain safe operating temperatures around heat-sensitive parts

• Disconnect power before servicing; some appliances contain high-voltage components
• Access location varies by model; note wire positions before removal and transfer one lead at a time
• Reuse existing mounting hardware; ensure firm terminal connections and correct orientation
• After replacement, confirm proper airflow/venting and normal operation

A replacement high-temperature cut-out that helps protect ovens by interrupting power if internal temperatures rise above safe levels. Restores the appliance's over-temperature protection so heating elements can be safely shut off when needed. What it does:

• Monitors oven temperature and opens the circuit if temperatures exceed a safe threshold to prevent overheating.
• Stops power to heating elements when tripped, preventing further temperature rise.
• Common symptoms of a failing cut-out: oven won't heat, continuous heating or no control over temperature, or oven shuts off unexpectedly.
• Used as a safety device in the oven's temperature-control system.

• Disconnect power at the breaker and allow the appliance to cool completely before servicing.
• Replace with the exact OEM cut-out and secure all wiring connections.

The Microwave Roller Guide Assembly is an essential component for maintaining the smooth operation of your microwave. This genuine OEM part ensures compatibility with a wide range of Samsung microwave models, providing reliable performance and durability. The Roller Guide Assembly is designed to facilitate the effortless movement of trays or turntables, preventing jams and ensuring consistent rotation during use. Its high-quality construction guarantees long-lasting functionality, allowing you to restore your microwave's performance without the need for expensive replacements. Installation is straightforward, making it an ideal choice for DIY repairs and saving you time and money. By replacing a worn or damaged roller guide, you can enhance the efficiency of your microwave, ensuring even heating and a better cooking experience. The Microwave Roller Guide Assembly not only improves the functionality of your appliance but also extends its lifespan, making it a practical and cost-effective solution for keeping your kitchen equipment in top condition.

Guide roller assembly that restores smooth, stable movement for a sliding rack or appliance drawer. Replaces worn or broken rollers to reduce sticking, grinding, or misalignment during use. What it does:

• Guides a sliding rack/drawer so it opens and closes evenly without binding
• Helps stop noisy or jerky movement caused by damaged or worn rollers
• Restores proper alignment to prevent racks from slipping or dropping
• Used where a roller rides along a track or guide to support smooth travel

• Disconnect power (and gas, if applicable) and remove any loose items from the appliance before beginning.
• Remove the affected rack/drawer or access panel to reach the guide; keep mounting hardware for reuse unless damaged.
• Align the guide and reinstall hardware securely; test the rack/drawer movement before completing reassembly.
• If mounting clips or brackets are broken, replace those parts as needed for a secure fit.

Ceramic

This control thermostat regulates the dryer's operating temperature. It senses exhaust air heat and cycles the heater on and off to maintain consistent drying performance and help protect the appliance from overheating. What it does:

• Monitors exhaust temperature and controls the heating element to hold the selected heat level
• Helps prevent overheating by cycling heat off when the target temperature is reached
• Supports even drying and consistent cycle times
• Typical failure symptoms: no heat or not enough heat, long dry times, runs too hot, inconsistent temperatures

• 1 control thermostat

• Disconnect power before servicing; if gas, also shut off the gas supply
• Access location varies by model; typically mounted on the heater housing or exhaust duct
• Transfer wire leads one at a time to the new thermostat and secure with the original screws
• After reassembly, clean the lint path and ensure good airflow to prevent repeat failures

This limit switch is a snap-action safety/position switch used in many cooking appliances. It opens or closes an electrical circuit when a mechanism reaches its limit, enabling safe operation and helping protect components when conditions aren't met.

• Provides snap-action switching to confirm a mechanical limit or interlock within the appliance
• Changes state to allow or interrupt power when the limit is reached
• Common failure symptoms: self-clean won't start or complete, oven won't heat/start, or door lock-related error codes
• May fail a continuity test or lose its distinct "click" when actuated

• Disconnect power before service; allow appliance to cool completely
• Access and mounting vary by model—take photos and transfer wires one at a time
• Mount in the same orientation; ensure the actuator/lever aligns with the mechanism and is not bent
• After installation, verify switch operation with a continuity test while actuating the mechanism

This limit switch interrupts power to a heating circuit when an over-temperature or unsafe condition is detected, helping prevent damage and unsafe operation. It's a direct-replacement safety control for affected appliances. What it does:

• Opens the circuit to stop heating when a temperature limit or fault condition is reached.
• Prevents overheating that can cause component damage or unsafe operation.
• Can cause no-heat, intermittent heating, or cycling behavior when failed.
• Works as a safety shutoff in heating systems and related control circuits.

• Disconnect power (unplug or shut off breaker) before accessing or replacing the switch.
• Access usually requires removing a panel or control housing; keep track of fasteners and wire locations.
• Handle terminals carefully and reconnect exactly as found; confirm secure wire connections.

This microwave thermostat is a temperature-sensitive safety switch that helps protect the unit from overheating. When the preset limit is reached, it interrupts power to the affected circuit to help prevent damage and erratic shutdowns.

• Monitors temperature at its mounting location and opens the circuit if overheating is detected
• Helps protect internal components from excessive heat
• Common symptoms of a failed thermostat include: unit shuts off during cooking, won't start until it cools down, or has no power/no heat due to an open safety
• Replace if the original tests open when it should be closed

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Microwaves contain a high-voltage capacitor that can retain a dangerous charge; only qualified persons should service and discharge the capacitor
• Note wire locations before removal and transfer connections firmly to the new thermostat
• Mount the thermostat securely and in the same position to ensure proper temperature sensing

This dryer inlet thermostat monitors the temperature of incoming air and cycles the heater to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent heat, help prevent overheating, and improve overall drying performance.

• Senses inlet air temperature and opens/closes electrical contacts to control the heat source
• Helps regulate drying temperature and protect against overheating
• Failure may present as long dry times, no or intermittent heat, overheating/shutting off, or erratic temperature swings
• Typically mounted on the air intake/duct or blower housing, depending on model

• Disconnect power before service; if gas, also shut off the gas supply
• Access the thermostat at the front duct or blower housing; note wire positions and transfer one at a time
• Mount flush against the metal surface with existing hardware to ensure proper sensing
• After installation, clear lint from ducting and vents to ensure proper airflow

Replaces the refrigerator temperature control thermostat to restore consistent cooling. This direct-replacement thermostat helps regulate compartment temperature so food stays at the set level and reduces temperature swings. What it does

• Senses compartment temperature and switches the cooling system on and off to maintain the selected temperature range.
• Helps prevent temperature fluctuations that can cause food to spoil or freeze unexpectedly.
• Commonly used when the refrigerator runs continuously, won't reach set temperature, or cycles erratically.
• Works with the existing control knob and wiring—intended as a like-for-like replacement.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Basic hand tools are typically required; take care not to damage the sensor bulb or capillary if present.

Rotating ring assembly supports the drum's rotating interface to maintain smooth, stable rotation. Replacing a worn or damaged ring reduces noise, vibration and scraping for quieter, more reliable operation. What it does:

• Holds and aligns the drum's rotating surface so the drum spins smoothly and evenly.
• Prevents metal-on-metal contact between the drum and cabinet or shaft.
• Worn or damaged rings can cause rubbing, grinding, squealing or excessive vibration.
• Restoring the ring can improve drum tracking and reduce noise during spin cycles.

• Disconnect power (and gas if applicable) before beginning any repair.
• Support the drum during removal to prevent it from shifting; follow the model's service diagram for correct disassembly.
• Inspect neighboring parts (rear drum bearing, glides, seals) for wear and replace as needed.