Solenoid Parts

This is a replacement gas valve for gas ranges and wall ovens that controls gas flow to the burner assembly, restoring proper ignition and heat control for appliance operation. Use when the burner won't light or won't stay lit. What it does:

• Regulates gas flow to oven/burner assemblies for safe ignition and temperature control
• Helps resolve ignition failures, weak or no burner flames, and intermittent heating
• Works with the appliance's ignition system to open and close gas supply as commanded

• One gas valve with included pipe

• Turn off the appliance's gas supply and electrical power before starting work
• Inspect fittings and gaskets; replace any damaged seals to ensure a gas-tight connection
• After installation, perform a gas leak test and check that burners ignite and operate correctly

Made by Whirlpool. Fits most Whirlpool, Kenmore, Estate and Roper belt driven washing machines.

This replacement coil controls the gas valve's opening and holding action during burner operation. Replacing a weak or failed coil restores reliable ignition and steady heat for consistent drying performance. What it does:

• Powers the valve to open during ignition (booster) and keeps it open while heating (holding)
• Helps resolve: igniter glows but no flame, burner lights then shuts off, no heat, intermittent heat/long dry times
• Restores proper gas flow for consistent temperatures
• Direct-fit electrical connection for the valve solenoid

• 1 booster & holding coil

• Disconnect power and shut off gas supply before servicing
• Allow the burner assembly to cool; access the gas valve compartment
• Label and disconnect wires; replace the coil in the same orientation; secure clips/brackets
• Restore gas, check for leaks with an approved solution, then test burner operation

This secondary gas valve solenoid coil energizes the dryer's gas valve so the burner can ignite and stay lit. Replacing a weak or failed coil restores consistent heat and helps resolve intermittent no-heat or flame drop-out issues. What it does:

• Works with the companion coil to open and hold the gas valve during burner operation
• A weak/open coil can cause tumbling with no heat
• Burner lights then goes out within seconds or heats intermittently
• Repeated clicking or glowing igniter without flame

• 1 secondary gas valve solenoid coil

• Disconnect power and shut off gas supply before servicing
• Access the burner/gas valve assembly; note wire positions and remove the old coil/retainer
• Seat the new coil on the valve stem, secure the retainer, and reconnect wiring firmly
• Restore gas and power; run a test cycle and check for leaks

• If one gas valve coil has failed, the companion coil is often near end-of-life; replacing both together can improve reliability

Replacement water inlet valve that controls water flow into the refrigerator's dispenser and ice maker, restoring proper filling and preventing overflows. Direct-fit design replaces the original valve on compatible Whirlpool refrigerators. What it does:

• Regulates water flow from the household supply to the refrigerator dispenser and ice maker.
• Opens when the dispenser or ice maker calls for water and closes to stop flow and prevent overfilling.
• Common symptoms: no water from the dispenser, slow/weak fill, ice maker not filling, or water leaking at the valve.
• Designed to match the original valve's function and plumbing connections for straightforward replacement.

• Disconnect power to the appliance and shut off the water supply before starting any work.
• Use basic hand tools to remove and reinstall mounting screws and water line fittings; support lines to avoid stress on fittings.
• Inspect and replace any damaged O-rings or supply tubing; tighten fittings securely but avoid overtightening.
• After installation, turn water on slowly, check all connections for leaks, then restore power and verify dispenser/ice maker operation.

This water inlet valve controls water flow into the appliance, allowing the correct amount of water to enter during fill cycles so the machine can wash properly and drain when commanded. Reliable operation helps prevent no-fill or overfill symptoms. What it does:

• Opens and closes to allow water into the washer during fill cycles.
• Enables correct water level and filling timing when signaled by the control board.
• Commonly replaces failing valves that cause no-fill, slow-fill, continuous filling, or leaking at the valve.
• Works with standard inlet hoses and connector fittings used on compatible washers.

• Disconnect power and shut off the water supply before servicing.
• Note hose and electrical connector locations before removal to ensure correct reinstallation.
• Tighten water connections securely and check for leaks after restoring water and power.

This switch/fuse kit replaces a worn or failed control switch and associated fuse to restore reliable power control. It provides the exact components needed to address common start and power interruptions. What it does:

• Replaces a faulty control switch to restore on/off or cycle control
• Replaces the protective fuse to stop power loss from a blown fuse
• Helps resolve no-start, intermittent power, or control failures
• Restores proper electrical continuity for safe operation

• Disconnect power to the appliance before starting any work
• Handle electrical components carefully and avoid metal contact with terminals
• Verify correct part orientation and secure all connections per OEM guidance

This replacement latch assembly secures the refrigerator or freezer door to ensure proper closure and reliable operation. It restores the door catch so the appliance can maintain an effective seal and help prevent cooling loss. What it does:

• Secures the door to keep it closed and aligned
• Replaces a broken, bent, or worn latch that prevents proper latching
• Helps reduce warm air entry caused by a door that won't stay shut
• Works as the mechanical catch that engages the door striker

• Disconnect power (unplug appliance) before servicing to avoid shock or injury.
• Remove the inner door panel or access trim as needed to reach the latch; keep screws and fasteners organized.
• Align the latch with the door striker and tighten screws securely without over-torquing.
• Test door operation several times after installation to ensure proper engagement and seal.

The Valve is an OEM part for Whirlpool refrigerators. As a critical ice maker component, the valve controls the flow of water to fill the mold and release ice cubes. 

Causes of a bad valve can include mineral buildup disrupting water passages over time, worn internal seals, or damage from freezing.

Symptoms of a bad valve are:  

• Irregular or incomplete ice filling in the mold
• Ice cubes sticking or failing to eject properly
• Water leaks inside or outside the ice maker
• Pressure issues preventing the ice maker from operating

This OEM Whirlpool part is also compatible with Maytag, Jenn-Air, KitchenAid, and some Kenmore models.

This maintop strike is the small latch plate the cooktop engages with to stay secured and aligned. Replacing a bent or missing strike restores a snug-fitting main top and proper engagement with the latch mechanism.

• Provides the engagement point for the main top's latch mechanism
• Helps keep the cooktop seated and aligned to reduce movement and rattling
• Can correct issues like the top not staying down or visible gaps at the front edge
• Supports proper actuation of any associated latch/safety switch, when applicable

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Open/raise the cooktop per the unit's design and support it safely
• Remove the old strike and align the new strike in the same position; reuse existing mounting hardware if applicable
• Tighten fasteners securely and test latch engagement before restoring power

This micro switch is a small electromechanical door/control switch that restores reliable on/off signaling for your appliance. Replacing a failed switch helps restore normal operation and safety interlocks. What it does:

• Opens or closes an electrical circuit when actuated, enabling controls or motors to run
• Commonly used in door and safety interlock applications to prevent operation when open
• Can stop intermittent power or control-response problems caused by a worn switch
• Helps resolve symptoms like appliance not starting, controls not responding, or cycling unexpectedly

• One micro switch

• Disconnect power (unplug appliance or flip the breaker) before servicing
• Observe sharp edges and wear protective gloves; remove access panels as needed
• Verify correct switch orientation and actuator engagement before reassembly
• Test continuity with a multimeter after installation to ensure proper operation

Replacement latch keeper for the dryer door latch assembly that secures the latch and keeps the door closed during operation. Restores reliable door engagement to help the appliance start and complete cycles. What it does:

• Secures the door latch so the dryer door stays closed during operation.
• Aligns with the latch mechanism to maintain proper door engagement.
• Common symptom: dryer door won't latch or feels loose, causing the cycle to not start or stop unexpectedly.
• Replaces worn or broken keeper pieces that allow rattling or misalignment.

• Disconnect power (unplug electric or shut off gas and breaker) before servicing.
• Access with basic hand tools; remove the door or front panel as needed to reach the keeper.
• Install carefully to avoid cracking surrounding plastic; do not force parts into place.
• After installation, verify the door closes securely and the dryer starts through a test cycle.

This precision-drilled burner orifice is sized for Type 4 butane applications. It meters gas to the burner so flames ignite reliably and burn cleanly when the appliance is configured for butane per the manufacturer's specifications. What it does:

• Regulates gas flow to the burner head for proper flame size and shape
• Type 4 drilling intended for butane gas configurations specified by the manufacturer
• Replaces a missing or stripped orifice during service or gas-type conversion

• 1 burner orifice (Type 4, butane)

• Shut off gas supply and power; allow the appliance to cool before service
• Access the orifice at the burner base/manifold; remove the original with the correct wrench or socket
• Start threads by hand; tighten snugly—avoid overtightening or cross-threading
• After reassembly, leak-check with soapy water and verify flame; gas conversions should be performed following OEM instructions and local codes

Float that detects and communicates water level to the appliance control so the washer or dishwasher can fill and drain properly. Replaces a cracked, stuck, or worn float to restore reliable water sensing. What it does:

• Senses water level and relays position to the machine's control system.
• Helps prevent overfilling or unintended continuous filling when working correctly.
• Can resolve symptoms such as flooding, constant filling, no fill, or improper drain cycles.
• Works with the appliance's existing valve and switch components to re-establish normal fill/drain operation.

• Disconnect power (and water supply where applicable) before beginning service.
• Remove outer panels or tub shroud to access the float; use basic hand tools.
• Handle clips and fittings gently; do not force plastic tabs or connectors during removal/installation.
• After installation, restore power and run a test cycle to ensure correct fill and drain behavior.

A replacement motor latch that secures the motor assembly to the appliance chassis, helping keep the motor stable during operation for smoother performance and reduced vibration. Fits specific Frigidaire/WCI motor assemblies. What it does:

• Secures and positions the motor assembly to prevent excessive movement
• Helps reduce vibration and rattling caused by a loose motor mount
• Restores proper alignment between motor and drive components
• Can eliminate intermittent contact-related noise from a shifting motor

• Disconnect power (unplug or switch off breaker) before starting any repair
• Installation typically requires accessing the motor area—expect to remove panels or the cabinet
• Keep track of mounting hardware; replace any damaged fasteners
• Test operation after reassembly; stop and recheck if noises or vibration persist