Gas Valve Parts

This LP gas conversion kit lets compatible gas ranges be converted from natural gas to LP (propane), supplying the correct orifices and settings so burners run safely and produce expected heat on LP fuel. What it does:

• Replaces factory burner orifices and related fittings to match LP fuel pressure and flow.
• Helps restore proper flame size and burner performance after switching from natural gas to propane.
• Addresses symptoms such as weak or yellow flames, uneven heating, or reduced burner output after fuel change.
• Intended for use only on ranges specified by the manufacturer for this conversion kit.

• Shut off the gas supply and disconnect power before beginning work.
• After installation, perform a leak test and verify correct flame characteristics on all burners.
• Keep original parts and the instructions for future reference and warranty requirements.

This surface burner valve regulates gas flow to a cooktop/range burner. Used in the left front or right rear position, it restores smooth knob control so the burner lights and the flame adjusts properly from simmer to high. What it does:

• Meters and shuts off gas to a single top burner
• Position-specific: intended for the left front or right rear location on the manifold
• Helps resolve issues like a hard-to-turn knob, inconsistent flame height, or a burner that won't adjust as expected
• Can correct no-gas flow to that burner when the original valve is blocked or failed

• 1 gas surface burner valve (LF/RR orientation)

• Shut off gas supply and disconnect power before servicing
• Lift the cooktop/top panel to access the manifold; note hose/tube routing and valve orientation
• Transfer any orifice holder/fittings from the old valve as required; avoid overtightening compression connections
• Use an approved gas-thread sealant if specified and leak-test all joints with a soap-and-water solution before use

This is a replacement gas valve for gas ranges and wall ovens that controls gas flow to the burner assembly, restoring proper ignition and heat control for appliance operation. Use when the burner won't light or won't stay lit. What it does:

• Regulates gas flow to oven/burner assemblies for safe ignition and temperature control
• Helps resolve ignition failures, weak or no burner flames, and intermittent heating
• Works with the appliance's ignition system to open and close gas supply as commanded

• One gas valve with included pipe

• Turn off the appliance's gas supply and electrical power before starting work
• Inspect fittings and gaskets; replace any damaged seals to ensure a gas-tight connection
• After installation, perform a gas leak test and check that burners ignite and operate correctly

This replacement part is a safety valve. This part is found in various types of refrigerators or freezers and is able to ensure that the appliance is running smoothly and safely during use. A new safety valve might be needed if the user notices that the current one is no longer working properly. This may include it having a leak or making unfamiliar sounds. The user should be able to access the back of the appliance to replace or repair this part.This is a genuine OEM replacement part made by Frigidaire, sold individually. The item, made of durable materials, is meant to last a long time.

This replacement coil controls the gas valve's opening and holding action during burner operation. Replacing a weak or failed coil restores reliable ignition and steady heat for consistent drying performance. What it does:

• Powers the valve to open during ignition (booster) and keeps it open while heating (holding)
• Helps resolve: igniter glows but no flame, burner lights then shuts off, no heat, intermittent heat/long dry times
• Restores proper gas flow for consistent temperatures
• Direct-fit electrical connection for the valve solenoid

• 1 booster & holding coil

• Disconnect power and shut off gas supply before servicing
• Allow the burner assembly to cool; access the gas valve compartment
• Label and disconnect wires; replace the coil in the same orientation; secure clips/brackets
• Restore gas, check for leaks with an approved solution, then test burner operation

This secondary gas valve solenoid coil energizes the dryer's gas valve so the burner can ignite and stay lit. Replacing a weak or failed coil restores consistent heat and helps resolve intermittent no-heat or flame drop-out issues. What it does:

• Works with the companion coil to open and hold the gas valve during burner operation
• A weak/open coil can cause tumbling with no heat
• Burner lights then goes out within seconds or heats intermittently
• Repeated clicking or glowing igniter without flame

• 1 secondary gas valve solenoid coil

• Disconnect power and shut off gas supply before servicing
• Access the burner/gas valve assembly; note wire positions and remove the old coil/retainer
• Seat the new coil on the valve stem, secure the retainer, and reconnect wiring firmly
• Restore gas and power; run a test cycle and check for leaks

• If one gas valve coil has failed, the companion coil is often near end-of-life; replacing both together can improve reliability

This safety valve controls and shuts off gas flow to the appliance burner assembly to help prevent unintended gas delivery. It restores safe operation when a failed valve is replaced and the ignition system is working properly. What it does:

• Regulates and stops gas flow to the burner/oven when the valve is closed
• Prevents gas from reaching the burner when ignition is off or unsafe conditions occur
• Common symptom fixes: no heat, continuous clicking with no ignition, or a persistent gas smell when appliance is trying to light
• Works with the appliance's ignition and pressure systems to maintain safe fuel delivery

• Turn off gas and power at the appliance before starting work
• Use appropriate tools and follow the appliance service manual; fittings may require thread sealant rated for gas
• After installation, check all connections for leaks with a non-corrosive leak detector or soapy water; do not use an open flame

This dual-type oven safety valve controls gas flow to the oven burners, restoring safe, reliable delivery of fuel for baking and broiling. Use it when the oven won't heat or gas flow needs proper regulation. What it does:

• Regulates and shuts off gas to the oven bake/broil circuits for safe operation
• Replaces a faulty valve that can cause no heat, intermittent ignition, or gas flow issues
• Works as the control point between the gas supply and oven burners to ensure proper fuel delivery
• Designed for direct replacement in compatible GE ovens

• One oven safety valve (dual type)

• Turn off gas supply and electrical power before starting any work
• Only connect fittings per manufacturer orientation; tighten and test all gas connections for leaks
• After installation, run a full ignition and leak test before normal use

This control valve is an important safety feature found on many gas ranges. It's located inside the back of the range near the area where the buttons and controls are found. The reason the control valve is included in ovens is to prevent gas from moving to the burners if the igniter is not able to ignite the gas or there is no electricity. The control valve could be faulty if there is a smell of gas near the valve, the burner flame flickers, or the flame cannot be turned on high.In any of these situations, the control valve must be replaced. The repair is easy and takes only a few minutes. The bottom of the oven will need to be removed, which may require a screwdriver. After removing it, remove the flame spreader by taking out two screws and sliding it out of the oven. Remove the screw holding the oven burner tube and take it out to access the valve and replace it.This control valve is made to be compatible with RCA, Kenmore, Roper, General Electric, and Hotpoint ranges. It's sold as an individual OEM replacement part that is sourced directly from the manufacturer.

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser, restoring normal ice production and water dispensing when the valve fails. Durable direct-fit replacement for affected GE refrigerators. What it does

• Opens and closes to supply water to the ice maker and dispenser when the dispenser or ice maker calls for water.
• Commonly used to fix no-water or low-water flow to the ice maker or dispenser.
• Stops water flow when the refrigerator is off to prevent leaks or flooding.
• Works with electrically controlled solenoid valves in the water system.

• One water inlet valve

• Disconnect power and shut off the household water supply before starting work.
• Access may require removing interior panels, the back cover, or toe panel depending on the model.
• Replace using the existing mounting and wiring connections; use new water line fittings if old fittings are corroded.

This gas surface burner valve controls the right-rear burner on your cooktop or range, regulating gas flow as you turn the knob. Replacing a worn valve restores consistent ignition and precise flame control at that position.

• Regulates gas flow to the right-rear surface burner for on/off and flame level control
• Common symptoms include no ignition, uneven or weak flame, or poor flame adjustment at that burner
• Stiff, loose, or wobbly knob action at the RR position can indicate internal valve wear
• If a gas odor is detected, shut off gas and have the unit serviced before use

• Disconnect power and shut off the gas supply before servicing
• Remove the knob and front panel to access the manifold; note valve orientation and connections
• Support the manifold with a second wrench while loosening/tightening fittings to avoid damage
• After installation, perform a soap-solution leak test on all connections and verify proper ignition and flame

This precision-drilled burner orifice is sized for Type 4 butane applications. It meters gas to the burner so flames ignite reliably and burn cleanly when the appliance is configured for butane per the manufacturer's specifications. What it does:

• Regulates gas flow to the burner head for proper flame size and shape
• Type 4 drilling intended for butane gas configurations specified by the manufacturer
• Replaces a missing or stripped orifice during service or gas-type conversion

• 1 burner orifice (Type 4, butane)

• Shut off gas supply and power; allow the appliance to cool before service
• Access the orifice at the burner base/manifold; remove the original with the correct wrench or socket
• Start threads by hand; tighten snugly—avoid overtightening or cross-threading
• After reassembly, leak-check with soapy water and verify flame; gas conversions should be performed following OEM instructions and local codes

This water inlet valve controls the flow of water to the refrigerator's dispenser and icemaker, ensuring reliable water delivery for drinking and ice production. Replace a failing valve to restore normal water flow and prevent leaks. What it does:

• Opens and closes to supply water to the dispenser and icemaker when needed
• Stops water flow to help prevent continuous filling or flooding
• Commonly used when dispenser water is weak, icemaker won't fill, or there is leaking near the valve
• Matches OEM function and fit for compatible Frigidaire refrigerators

• One water inlet valve

• Shut off water and power to the appliance before starting any repair
• Handle water lines and electrical connectors carefully; replace worn gaskets or seals as needed

Replacement burner valve that controls gas flow to a surface cooktop burner, restoring reliable flame control for safer, consistent cooking. Use this valve when a burner has low or no flame, uneven flame, or won't respond to knob adjustments. What it does:

• Regulates gas flow to a single surface burner so you can adjust flame size and cooking heat.
• Replaces valves that cause burners to fail to light, produce weak or sputtering flames, or not change flame level.
• Restores normal burner operation when the original valve is worn, leaking, or damaged.
• Compatible with gas cooktops and ranges.

• Turn off the gas supply and unplug the appliance before starting any repairs.
• Use appropriate hand tools; avoid overtightening fittings or damaging gas lines.
• After installation, check all connections for leaks (soap-and-water test) and verify proper burner ignition and flame.

This genuine OEM part is an oven safety valve for gas ovens. The oven safety valve is designed to prevent gas from flowing to the burner assembly if the igniter is not hot enough to ignite the gas, or if no electricity is present. Over time, an oven safety valve can become inoperable due to excessive wear and tear. If the oven is no longer heating properly, not turning on, or no longer working as powerfully as it once did, the oven safety valve will need to be replaced.To replace this part, start by unplugging the oven and shutting off the gas supply. After that, move the range away from the wall. Use a wrench to unthread the nut to remove the gas supply tube from the safety valve. Next, open the oven door to gain access to the interior of the oven. Release the hinge locks that secure the door and pull the door off the oven. Remove the oven racks and proceed to unthread the screws that secure the oven's bottom panel. Once removed, locate the safety valve. Next, unthread the screw that holds the mounting bracket into place. Remove the old safety valve and align the new valve with its mounting bracket. Attach the wires to the safety valve terminals and reinstall the bottom panel and oven door.This replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with General Electric, Hotpoint, and RCA brand ovens.