Loose Band Wire Connection Parts

This is the appliance's main power cord. It delivers household electricity to the unit so it can operate safely and reliably.

• Supplies AC power from the wall outlet to the appliance's internal wiring
• A damaged or failed cord can cause no power, intermittent power, or tripped breakers
• Replacing a worn cord can restore consistent power and improve safety

• Unplug the appliance and turn off power at the breaker before service
• Route and secure the cord to prevent pinching or abrasion

This burner wire harness connects the range/oven ignition system components so the burner safely receives the correct spark or hot-surface signal. It replaces a damaged or worn harness to restore reliable ignition performance. What it does:

• Routes electrical connections from the igniter/spark module to the burner assembly
• Enables ignition sparks or hot-surface signals to reach the burner for reliable lighting
• Can stop symptoms such as burners failing to light, erratic or intermittent ignition, or continuous clicking
• Helps prevent loose or shorted wiring that can cause ignition faults

• Disconnect electrical power and shut off gas supply before starting any repair
• Label or photograph original wiring locations to ensure correct reconnection
• Route the harness clear of direct heat and moving parts; secure with original clips or ties

This dishwasher hose clamp secures a hose to its fitting to help prevent leaks. Replace a corroded or loose clamp to restore a tight, reliable seal at a hose connection point. What it does:

• Tightens around a dishwasher hose and fitting to maintain a watertight seal
• Helps resolve leaks at hose joints or beneath the unit
• Replaces clamps that are corroded, bent, stripped, or won't hold tension
• Symptoms include moisture at the connection, hose slipping off, or recurring leaks

• Includes 1 hose clamp

• Disconnect power at the breaker and shut off the water supply before servicing
• Access the affected hose connection and place a towel or pan to catch residual water
• Release and remove the old clamp; fully seat the hose, position the new clamp just behind the fitting's barb, and tighten/secure
• Run a short cycle and check for leaks at the connection

This locking clip secures a mating component inside the washer, keeping it firmly attached to its mounting point. Replacing a worn or missing clip restores a snug fit and helps prevent movement, intermittent connections, and noise during operation.

• Retains the designated component securely to its bracket or panel
• Helps prevent vibration-related movement, rattling, or disconnection
• Maintains proper alignment for consistent operation
• Typical signs of failure: cracked or missing clip, part won't stay seated, new looseness around the mount

• Disconnect power and turn off water before servicing
• Access the clip location per your model's service information
• Release and remove the old clip; inspect the mating part for damage or wear
• Seat the new clip fully until it locks; verify the component is secure before reassembly

This clip secures the evaporator thermistor to the evaporator tubing so the control can read coil temperature accurately. Replacing a damaged or missing clip helps restore correct cooling and defrost performance by keeping the sensor firmly in place. What it does:

• Holds the evaporator thermistor tightly against the evaporator coil/tubing for accurate temperature sensing
• Supports proper cooling regulation and defrost cycle timing
• A loose or misplaced sensor may show temperature swings, long run times, or frost buildup on the evaporator
• Restores correct sensor placement after repairs or when the original clip is lost or broken

• 1 evaporator thermistor clip

• Unplug the refrigerator; interior metal edges and fins are sharp—wear cut-resistant gloves
• Remove the evaporator cover to access the sensor; note the original sensor location and orientation
• Transfer the thermistor into the new clip and attach it at the same spot so the sensor makes firm contact; do not pinch wires
• Reinstall panels, keep wiring clear of the fan, and restore power

This clip is a hose clamp used in select laundry appliances. It secures a hose connection to prevent leaks and keep water or air moving where it should, helping maintain reliable washer or dryer performance.

• Secures hose to its fitting to prevent leaks or disconnections
• Helps resolve issues like leaking at a hose joint, loose hose, or poor draining/airflow related to a slipped hose
• Durable spring-style clamp designed for repeatable tension
• Commonly used on internal washer or dryer hose connections

• Unplug the appliance and turn off water supply before service
• Have a towel or pan ready for residual water when removing hoses
• Use pliers to compress and slide the clamp; note original clamp position for reassembly
• Inspect hose ends for cracks; replace the hose if damaged before reinstalling the clamp

This door spring restores the proper counterbalance of the oven door so it opens smoothly and closes with controlled tension. Replacing a worn or broken spring helps prevent the door from dropping, slamming, or sitting unevenly.

• Provides counterbalance tension for the oven door through the hinge mechanism
• Helps the door open smoothly and hold at a partially open position
• Maintains even alignment and consistent gasket contact
• Common symptoms of failure: door feels heavy, drops open or slams, uneven door height, squeaks during movement

• Disconnect power at the breaker and allow the oven to cool completely
• Springs are under tension—support the door and use caution to avoid injury
• Note the spring's routing and anchor points before removal; reinstall in the same positions
• For even tension, consider replacing both door springs when the design uses one per side

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power

This replacement power cord provides the appliance's main AC connection so it can receive power and operate reliably. It restores a safe, factory-style power connection when the original cord is damaged or worn. What it does

• Supplies mains power to the appliance through the cabinet connection
• Replaces frayed, cut, melted, or damaged cords that cause intermittent power or no power
• Helps eliminate burning smells, arcing, or visible insulation damage at the cord
• Matches OEM electrical connection style for proper fit and secure contact

• One power cord assembly

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the cord
• Verify cord routing and strain relief position to prevent pinch points or abrasion
• Use proper tools and fasteners; tighten connections securely but do not overtighten

This replacement defrost heater warms the freezer's evaporator area during the automatic defrost cycle. It melts accumulated frost so air can circulate, helping maintain stable temperatures and preventing ice buildup on the back wall.

• Heats the evaporator to clear frost and ice during defrost
• Helps keep airflow passages and the defrost drain path open
• Common symptoms of a failed heater: heavy frost on the back panel/coils, poor cooling or warm sections, fan noise from ice contact, cooling returns temporarily after a manual defrost
• Typically located behind the rear freezer panel

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator by removing the freezer's rear panel; thaw heavy ice before removal
• Transfer any clips/brackets and route wires exactly as original, keeping them away from plastic parts
• After installation, ensure wiring connections are secure and the heater is not contacting plastic surfaces

This wiring harness connects and routes power between key refrigerator components, restoring proper electrical signals so fans, lights, compressor and ice/water functions can operate correctly when the original harness is damaged. What it does:

• Provides the factory routing and connectors to link controls, motors and sensors
• Replaces frayed, burnt or broken wires that can cause intermittent power or no-power to components
• Helps resolve symptoms such as lights or dispenser not working, fans not running, or ice maker/pump failures when wiring is the cause
• Maintains factory-style connector fit and wire lengths for correct component connections

• Disconnect power to the appliance before inspecting or replacing the harness
• Match the part number and connector shapes to the original; route and secure wires per factory clips to avoid heat or pinching
• If connectors are corroded or terminals are damaged, replace the harness rather than attempting temporary repairs

Wire harness with LED assembly that connects an appliance's control circuitry to an LED indicator or lighting module, restoring proper indicator illumination and signal routing when the original harness is damaged or intermittent. What it does:

• Provides the electrical connection and mounted LED used for control/indicator or internal lighting circuits
• Transfers power and signal between the control board and the LED/indicator
• Can correct symptoms such as a dim, flickering, or non-lighting indicator or intermittent LED function
• Replaces a damaged or corroded connector that causes loss of indicator/lighting

• Disconnect power to the appliance before attempting replacement to avoid shock or damage
• Handle connectors and the LED assembly carefully to avoid bending pins or damaging wiring
• Route and secure the harness to match original routing and avoid pinch points or heat sources
• Test operation after installation; for wiring diagrams and connector locations

This small clip secures a component, panel, or cover so it stays firmly in place during appliance operation. Replacing a bent or missing clip restores a tight fit and helps eliminate unwanted movement or vibration.

• Retains a panel, cover, bracket, or harness at its mounting point
• Helps prevent shifting, rattling, or parts coming loose
• Direct replacement for a broken, bent, or missing clip
• Common symptoms: loose or sagging panel/cover, buzzing or rattling noises, part that will not stay attached

• Disconnect power and, if applicable, shut off gas/water supplies before servicing
• Note the original clip's orientation; take a photo for reference
• Use needle-nose pliers for removal/installation; avoid over-bending the clip
• After installation, ensure the clip is fully seated and clears any moving parts

A wiring harness that routes power and signals between a refrigerator's internal electrical components, helping lights, controls, fans and motors operate correctly. Replacing a damaged harness restores reliable electrical connectivity and reduces risk of intermittent faults. What it does:

• Routes power and signal connections between the control board, lights, motors, sensors and other internal components.
• Common visible issues include frayed insulation, broken or loose connectors, or heat damage at terminals.
• Replacing a faulty harness helps eliminate wiring-related faults that can cause component failures or safety concerns.

• Always disconnect power (unplug appliance or shut off circuit breaker) before inspecting or replacing the harness.
• Match connector shapes and pin counts; route the harness along the original path and avoid tight bends or pinch points.
• Secure with the existing clips or ties; replace damaged clips or protective insulation as needed.

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

This ignitor harness connects the oven ignitor to the range's wiring, restoring a secure electrical path for reliable ignition. Replacing a damaged harness can help get your gas oven lighting and heating properly again. What it does:

• Transfers power from the oven wiring to the ignitor so the burner can light.
• Replaces frayed, burned or broken wires that can cause intermittent ignition or no ignition at all.
• Improves connection integrity to reduce sparking or loose-contact symptoms.
• Common symptoms this part can address: oven won't light, bake/broil doesn't heat, or ignitor fails to glow.

• Turn off electrical power and gas supply before starting any work; ensure the appliance is cool.
• Remove access panels and disconnect old harness at terminals; compare connectors before installing the new harness.
• Make secure, tight connections and route the harness away from sharp edges and high-heat surfaces.