362-72286890 Parts

• Little to no heat when broiling
• Little to no heat when baking
• Gas igniter glows, but will not light
• Won't start

If the oven burner would not light but the broiler would this indicated that the safety valve is OK. Problem had to be with the igniter. Removed the bottom panel in the oven and restarted the oven. The igniter would not glow at all. It should be brilliant red. This is where the problem came in. I could not find the location of the model on the Kenmore range anywhere you would normally look - the back, the wiring envelope, the oven door jamb etc. Also the igniter cannot be removed from... Read more

Ordered New Gasket and installed in about 3-4 Minutes. Only need small pliers to remove some of old clips from holes. New Gasket clipped in easily by hand. Read more

Orded rack by stove model number. fit perfect Read more

• Won't start

Took off old, replaced with new. Cross reference worked well, all GE parts. Saved a lot of money compared to local supplier. Read more

Replaced the oven burner, ignitor, and the safety valve. Read more

It was a Friday afternoon, of course, I went to my local supply house for the part. I did look it up on your site first to see what I needed and how much I was looking to pay. I got there and "They don't stock those!" I said thank you and went to do more hunting. I ended up at what I found to be the only other parts place in town, and they could've ordered it, for much more than you, I don't mind paying more to get it now but am not going to wait a week to pay more. I said no and came home,... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start

The repair was relatively simple and quick. The only part required was a new oven thermostat assembly and the tools I used for my model was a flathead screwdriver, cross-point screwdriver, torque bit and 1/4 inch socket using a bit driver. To complete the repair, I did the following: 1. Remove all top stove burner pieces and place to the side. Remove the 3 three screws (torque bit) in each of the 4 burner locations. That will allow the top lid to separate from the main unit later. 2. Pull... Read more

It was a Friday afternoon, of course, I went to my local supply house for the part. I did look it up on your site first to see what I needed and how much I was looking to pay. I got there and "They don't stock those!" I said thank you and went to do more hunting. I ended up at what I found to be the only other parts place in town, and they could've ordered it, for much more than you, I don't mind paying more to get it now but am not going to wait a week to pay more. I said no and came home,... Read more

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more

Replaced the oven burner, ignitor, and the safety valve. Read more

Called Appliance Parts - service agent was extremely helpful. Tried to find an assembled piece was unable to do so. Send me the individual parts which were very easy to assemble. Was able to replace entire light assembly, reconnect wire with new terminal end. Light works find just now. Would definitely call again if I needed assistance. Read more

Looked for the parts at this site and ordered those need plus spares Read more

Removed the front off the back panel, unplugged the old unit. Then using a blow dryer heated the old timer to peel the face /cover off and applied to the new clock. Plugged in the replacement clock. Replaced the front of the range. The only complaint I have is we were not informed that a new face would not be included and the old one would have to be removed and applied to the replacement clock. The face that was on the orginal clock has the buttons to set the clock and timer reversed from... Read more

Replaced spark module and all electrodes/igniters. Read more

AppliancePartsPros identified problem and needed parts. Repairman installed new spuds. Read more