Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Transfers power from motor to drum in your dryer. Replace if squeaking, not spinning, or visibly worn. Confirm fit with your model number before ordering.
First, I did a search based on the problem I had with my model of dryer. The model number was on the door frame and was visible when I opened the dryer door. The problem was, when I pressed the button to start a dryer cycle, I heard a clicking noise and the indicator text changed to "Drying", but I could not hear or see the dryer drum turning. The search led me to a page that indicated my problem was usually one of 3 common causes. 1. Faulty door switch 2. Broken Drum drive belt 3. burned out... Read more
The Dryer Front Bearing Drum Slide (White, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The white slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.
Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more
The Dryer Front Bearing Drum Slide (Green, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The green slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.
Rear drum bearing kit supports and smoothly rotates your dryer drum. Replace when you hear squealing, screeching, or grinding noises. Verify fit with your model.
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more
Seals the gap between the drum and front panel to prevent air leaks and noise. Replace if worn, damaged, or causing squeaking sounds. Verify fit with your model.
Found the entire top bearing support plastic piece was completely worn through, the bearing slides had all disappeared some time ago. So it was obviously the problem. The felt trap duct (which is actually a drum seal along bottom front of drum so I don't know why they call it felt trap duct) had also disappeared, so a lot of lint was getting inside the front panel too. It's a very easy repair to change the bearing support; everything just pops out just like the video shows. Make sure you... Read more
Maintains tension on your dryer's drive belt. Replace if pulley is cracked, worn, or making noise. Installs inside drum assembly for smooth operation.
Illuminates your dryer drum for better visibility when loading and unloading clothes. Replace when burned out or flickering. Verify fit with your model.
It was an easy repair just screwed in. The ordering process and simple no hassle and got here fast! I will definitely order from you again Read more
Supports the rear dryer drum for smooth, quiet rotation. Replace if you hear squeaking, screeching, or thumping during cycles. Verify fit with your model.
First symptoms were squeaking drum. This is probably when new glide strips might have been all that we needed. But I put off fixing it... and I put it off some more. Noises got louder, squeaking became screeching, then it started to vibrate loudly. The front drum bearing (really just a plastic arch that the drum rides on) had broken, and with the drum in a canted position, the rear bearing sleeve got messed up too. I ordered the front drum support bearing, and also a rear drum bearing... Read more
Dishwasher won't start or runs intermittently? A faulty door interlock switch prevents operation when the door latch fails. DIY repair in 20 minutes.
The full story: Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the... Read more
Dryer not heating or stops mid-cycle? A faulty inlet thermistor may prevent proper temperature regulation. This sensor monitors incoming air temperature.
Replaced the inlet control thermis (thermostat) . Now it completes the cycle but clothes are not 100 % dry. I would add 15 minutes more and that helps. FYI: you don't need to remove the drum, just remove the top cover and that will give you enough space to replace the sensor Thank you Appliance Parts for your fast speed of delivery. Read more
Dryer won't start or humming when you press start? The door switch signals when the door is closed. Easy 15-minute DIY repair with basic tools.
I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more
Supports the rear drum for smooth rotation. Replace when you hear squealing or screeching noises during the drying cycle. Confirm fit with your model number.
Dryer shuts off too soon or won't heat? A faulty high limit thermostat often causes premature shutoff. Simple DIY fix—usually takes 15 minutes or less.
Changed out high limit thernasstat Read more
Dryer not heating or producing no heat? A faulty igniter prevents gas ignition. Moderately difficult repair with basic tools. Video guide available.
Changed ignitor. Ordered new ignitor by just putting dryer model number in the search box. When I opened the dryer up and took the old one out I was originally upset. The meter read 73 ohms. I was expecting OL (open line). The new one read 273 ohms so I put it in. Dryer works now. The install video’s are old. It was much easier than the video’s showed. Opening the control panel was a little trickier than the video. You do NOT need to take screws off the back of the dryer. There are 2 screws... Read more
Dryer door won't stay closed? A worn or broken door strike prevents proper latching. Easy 5-minute DIY fix with basic tools. Video guide included.
Replaced door strike and door latch Read more
Seals the drum bearing assembly to prevent air leaks and maintain drying efficiency. Replace when worn, cracked, or if dryer is noisy. Confirm fit with model.
Went ahead and replaced the pulley as well the drum bearing sleeve and O ring, drum belt and the front drum bearing slides. Put the unit back together and she ran like a top! Read more