Zgu36n6hss Parts

This is the surface burner igniter switch that mounts on the valve stem and closes the circuit to spark the burners when you turn the knob. Replacing a faulty switch restores consistent, reliable ignition on your gas cooktop or range.

• Closes when the knob is turned to send power to the spark module
• Helps resolve intermittent or no spark at one or more burners
• 12 o'clock orientation matches the valve shaft's flat position for proper fit

• Disconnect power and shut off gas before servicing
• Pull off the knob and access the switch from the control panel
• Note wire positions before transfer; replace one switch at a time
• Verify correct shaft orientation (12 o'clock) to match your valve style

This formed gas tube routes fuel to the front surface-burner section on select gas ranges and cooktops. Replacing a damaged or clogged tube restores proper gas flow and reliable ignition to the front burners.

• Distributes gas from the supply/manifold to the front row of surface burners
• Helps address front burners not lighting, weak/uneven flame, or gas odor when the original tube is damaged or obstructed
• Maintains factory routing and clearances under the cooktop
• Direct-fit shape to match the original path and connections

• Shut off gas supply and power; allow the appliance to cool before servicing.
• Access tubing under the cooktop/rangetop; note routing and orientation before removal.
• Support fittings with two wrenches; avoid kinking or over-bending the new tube.
• After installation, perform a thorough leak check with an approved leak-detection solution before restoring gas and power.

This igniter assembly creates the spark that lights a gas burner, helping restore quick, reliable ignition. Replacing a damaged or shorted igniter can address burners that won't light, intermittent ignition, or repeated clicking without flame.

• Generates a high-voltage spark at the burner to ignite gas
• Ceramic-insulated electrode focuses the spark for consistent lighting
• Failure can cause no spark at a specific burner, delayed ignition, or constant clicking
• Visible cracks, carbon tracking, or damaged lead are common replacement indicators

• Disconnect power and shut off gas before servicing
• Allow the appliance to cool; handle the ceramic insulator carefully to avoid breakage
• Route the lead away from heat and moisture; secure connections firmly
• Align the electrode tip correctly with the burner for reliable ignition

This chamfered nut is a genuine fastener used to secure mating parts inside your appliance. It replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and proper alignment.

• Provides threaded clamping force to fasten components
• Helps maintain alignment and resist loosening from vibration and heat cycles
• Replaces rounded, stripped, corroded, or missing nut
• Typical symptoms: loose panels/brackets, rattling noises, or parts shifting out of place

• Disconnect electrical power; turn off gas supply before servicing
• Allow the appliance to cool completely; wear gloves and eye protection
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Match orientation/position to the original

This six-point spark ignition module for gas cooktops/ranges converts line voltage into high-voltage pulses that fire the burner igniters. It restores consistent, reliable lighting across multiple burners when you turn a knob.

• Distributes high-voltage pulses to up to six surface-burner igniters when a burner switch is turned on
• Helps resolve no spark/click on all burners, no spark on some burners, intermittent ignition, or continuous clicking
• Replaces a module that produces weak, erratic, or no spark
• Ignition control only; it does not regulate gas flow or flame size

• Disconnect power and shut off gas before servicing
• Photograph and label all wires; transfer them one at a time to the matching terminals (six HV outputs plus power/ground)
• Mount securely in the original location and keep connections dry; after installation, ensure burner caps are seated and igniters are clean

Ranges and ovens have grate feet installed on the underside of their cooktop grates. This rubber piece keeps the stovetop from getting scratched by the grate when there is pressure applied. With use, misplacement, or other damages, there is a requirement for one more replacement grate foot pieces.A stovetop with scratches on the surface indicates a missing grate foot. There are four grate foot parts on each grate. The replacement of a grate foot is a simple process. Remove the grate covering the area where a visual inspection has determined there is a missing foot grate. Clean the area thoroughly. Apply the new foot grate. Reposition the grate on the stovetop. Wear gloves for safety. It's recommended to unplug the appliance while doing the replacement to prevent accidental activation of the cooktop.This grate foot is an authentic OEM replacement part. It is sold as an individual unit. It is made of high-quality, durable rubber. The piece is sourced directly from the manufacturer. It is compatible with several models of ranges and cooktops. The grate foot fits in appliances produced by General Electric, RCA, and Hotpoint.

A left-side double burner pan that supports two cooktop burners and helps contain spills and drips for easier cleanup. Durable replacement to restore proper burner support and alignment on compatible gas ranges. What it does

• Holds and centers two adjacent burners so pots and pans sit flat and stable.
• Helps catch food, grease and liquids to prevent spills from reaching the cooktop cavity.
• Fits into the left-side pan location and works with the cooktop's burner assembly.

• Allow the cooktop to cool and shut off power/gas to the appliance before starting.
• Remove grates and existing pans carefully; align the replacement pan to the burner openings and set into place.
• Use non-abrasive cleaners to avoid damaging the finish; avoid bending or flexing the pan during install.

This D simmer ring fits the cooktop burner to help control and focus the gas flame for low-heat cooking and simmering. It restores proper burner alignment and helps prevent uneven heating on compatible gas ranges. What it does:

• Centers and supports the burner cap so the flame burns evenly
• Narrows the flame for low-heat/simmer settings and gentler cooking
• Helps reduce hot spots and improves stove-to-pot heat transfer
• Resolves uneven or wandering flames when the original ring is warped or damaged

• Turn off all controls and ensure the range is completely cool before servicing
• Remove grate and burner cap, seat the simmer ring over the burner base, then replace cap and grate
• Inspect for cracks, warping, or heavy corrosion; replace if damaged
• If you smell gas or the flame remains abnormal after installation, stop use.

This high-voltage transformer steps line voltage up to power the magnetron, producing microwave energy. Replacing a failed transformer can restore heating when the oven runs but doesn't heat or hums without cooking.

• Supplies the high voltage the magnetron needs to generate microwave energy
• Failure may present as the microwave running but not heating
• May cause a loud hum or buzz with no heat
• Can blow an internal fuse or trip a breaker immediately after pressing Start

• Disconnect power before service; the high-voltage capacitor can retain a dangerous charge even when unplugged
• Support the heavy transformer during removal/installation and reuse original mounting hardware and wire positions
• After installation, verify secure connections in the high-voltage circuit (capacitor and diode) before testing

A replacement D port trim ring that restores the finished opening and secures a vent/port on the appliance. Replaces a cracked, broken or missing trim piece to stop drafts and eliminate rattling. What it does:

• Provides a finished, stable edge around a D-shaped port or vent opening
• Helps hold a hose or duct in position and reduces movement
• Reduces air leaks and vibration-related noise when damaged or loose
• Commonly replaced when the trim is cracked, warped or missing

• Disconnect power and follow the appliance manufacturer's safety instructions before starting
• Small screws or clips may secure the ring; keep hardware organized for reassembly
• Expect simple, moderate-level access; removing a panel may be required
• Wear gloves to protect against sharp sheet-metal edges

This LP/NAT conversion kit contains the orifice spuds and instructions needed to convert a compatible gas range or oven between liquid propane (LP) and natural gas so burners operate with the correct fuel flow and combustion. What it does:

• Replaces factory orifice spuds to match the appliance to LP or natural gas
• Restores proper burner flame size and performance after conversion
• Helps prevent incomplete combustion caused by incorrect orifice sizing
• Use when appliance was shipped for a different fuel type or after regulator changes

• Turn off gas supply and electricity before servicing; leak-test all connections after installation
• Follow the appliance's service manual and conversion instructions exactly
• Use the correct orifice(s) for your fuel type
• Retain removed parts and documentation for warranty and service records

This grate support is the cooktop bracket that holds and stabilizes a single burner grate so cookware sits level while you cook. It restores proper support and reduces grate wobble for safer, more even cooking. What it does:

• Supports and secures a cooktop burner grate in its correct position
• Prevents grate rocking or shifting while placing or moving cookware
• Helps maintain even heat contact by keeping grates properly aligned
• Commonly used when a support is cracked, worn, or broken

• Inspect surrounding cooktop area for damage before installing; replace any additional worn supports
• Disconnect power to the appliance (or shut off gas and ensure burners are cool) before working on the cooktop
• Install with original fasteners or OEM replacements; tighten securely but avoid overtightening

This landing edge kit replaces the worn or damaged landing edge on compatible GE appliances to restore a secure, even door or panel fit and reduce drafts or rubbing. Designed as a direct-fit service part for affected models. What it does

• Replaces the landing edge strip that provides a finished, cushioned contact surface for a door or panel.
• Helps stop scraping, rattling, or uneven closing caused by a worn or torn landing edge.
• Restores the proper seal/contact area to reduce air leaks and improve door alignment.
• Keeps surrounding trim from wearing prematurely by providing a consistent contact surface.

• One landing edge kit (ZDP) as shown.

• Verify accessibility and remove power from the appliance before starting.
• Clean the mounting area and remove old adhesive or remnants to ensure good fit and adhesion.
• Use appropriate hand tools; avoid sharp tools that could damage adjacent trim or seal surfaces.
• Follow any model-specific instructions in the service manual for proper positioning and attachment.