Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Leaking water from your refrigerator or no water/ice from dispenser? This water inlet valve controls flow to ice maker and dispenser. DIY repair in 30 min.
I replaced the solenoid valve and trimmed a small amount of the tubing that serves the ice maker and water dispenser. The only problem was there is almost NO slack in that tubing. If you trim more than a half inch off, you won't have enough tubing to connect it on both ends. Read more
Ice maker stopped working or producing misshapen ice? This complete assembly replaces a faulty ice maker. Moderate DIY repair, about 1 hour with basic tools.
This was easier then I made it. Originally took the actual ice maker out without removing the whole system from the door. There are 3 silver screws that do that hold the whole mechanism in place, as opposed to the 5 white screws that hold the ice maker in place. With the entire assembly out it was a matter of routing the ground wire, retaping the wires, and then the whole assembly went back into the door without a problem. Need a phillips and a flat screwdriver, I also found a needle nose... Read more
Fix a stuck or non-working ice/water dispenser with this micro switch. Common cause of dispensers running continuously or not activating. Easy DIY repair.
After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more
Connects French doors on refrigerators. Replace if cracked, broken, or spring-damaged. Installs between doors to maintain proper seal alignment.
Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more
Refrigerator stopped cooling after power outage? The compressor overload protector prevents overheating damage. Easy DIY fix when compressor won't run.
Removed and replaced the compressor start relay. Read more
Refrigerator not cooling or freezer warm? The compressor assembly circulates refrigerant to maintain temperature. Professional installation recommended.
Ordered a new compressor and repaired by 3rd party. Read more
Controls ice dispenser door opening and closing. Replace if door won't open, stays open, or motor makes no sound when dispensing. Mounts behind dispenser trim.
Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more
Fixes refrigerator running warm or compressor area overheating. This fan motor assembly circulates air over the condenser coils to regulate temperature.
Plastic door stop that limits refrigerator door swing range. Replaces broken, cracked, or missing stoppers causing doors to swing too wide or close improperly.
1. Googled "appliance replacement parts" - found two sites to consider 2. Researched parts needed via a exploded diagram - can't fix it if you can't name it. 3. AppliancePartsPros.com had the easiest diagram and after checking, the lowest price. 4. Parts showed up within a couple of days - an in-transit note was helpful. 5. The part screws in but watch out you don't break the tiny black pin holding the part on in addition to the screw. Needed JB Weld to fix that. Read more
Fix no water or ice issues with this water inlet valve. Common when ice maker won't fill or dispenser trickles. Easy 10-minute DIY with video guide.
Replaced icemaker Read more
Keeps refrigerator air fresh by filtering odors and contaminants. Replace every 6 months or when indicator alerts. Confirm fit with your model number.
Just wanted to say how incredibly nice and helpful the gentleman was that helped me on the phone when I called to place the order. Very nice..... Read more
Stores and supplies water to your refrigerator's dispenser and ice maker. Replace if cracked, leaking, or damaged from mineral buildup or freezing.
Replaced tank assembly. Actually I think the supply hose was originally not fully seated in the tank and I think I could have re-seated it deeper through the gray bushing. When I set the line into the new tank, still leaking. Pulled out supply line and reset using a little more force and line went into the tank. Took the bushing clip off the other tank and used it for the supply line bushing. So far, no leaks. The thing to remember is to push the edges of each hose bushing inward to pull... Read more
Hinge assembly for refrigerator doors. Installs at door pivot point to support door weight and enable smooth opening/closing. Replace if cracked or worn.
There is one hinge on top and one at the bottom, but it was none of these it ended up being this hinge that I ordered. Door was having a little hesitation at closing, the door would not pull your hand to close or it would not closed by itself. replaced this part and the refrigerator was fixed. Read more
Clear plastic storage bin that mounts inside refrigerator door. Replace if cracked, broken slide pegs, or loose assembly from temperature changes.
Found right part and it was delivered in three days Read more
Seals the ice bank door to prevent warm air from melting ice and causing clumping. Replace if ice melts, refreezes into clumps, or frost forms around the bin.
We have an LG fridge that is 10 years old that was starting to have sweating problems around all the gaskets. So it was either a new fridge or try replacing the gaskets. I purchased a new ice maker door gasket using the parts catalog on the website. Very easy to order and they offer a short video to show the technique to switch out the old and new gaskets. Also did the same thing with the door gaskets and freezer drawer gasket. Website was very easy to work with and find the correct parts and... Read more
Replacement mounting stud for refrigerator door handles. Installs inside the door to secure handle assembly. Needed when stud is damaged or missing.
Ordered new freezer arm Read more