Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer won't start when you press the button? This rotary start switch activates your dryer cycle. Simple DIY fix in minutes with basic tools.
Looked at the diagnostic help on Appliance Parts Pros.com and the start switch was the problem, but only 25% of the time, so I was a little concerned it may be a different problem. The switch was reasonably priced, so I ordered it and it arrived in two days! It was very easy to follow the repair video, however, my GE Gas dryer had a lot of screws rather than 2 screws and tabs on the model in the video, so it took a little more time to open up. After turning off the gas and unplugging the... Read more
Dryer not heating or producing no heat? A faulty igniter prevents gas ignition. Moderately difficult repair with basic tools. Video guide available.
Changed ignitor. Ordered new ignitor by just putting dryer model number in the search box. When I opened the dryer up and took the old one out I was originally upset. The meter read 73 ohms. I was expecting OL (open line). The new one read 273 ohms so I put it in. Dryer works now. The install video’s are old. It was much easier than the video’s showed. Opening the control panel was a little trickier than the video. You do NOT need to take screws off the back of the dryer. There are 2 screws... Read more
Dryer drum belt wraps around drum and motor pulley to spin the drum. Replace if dryer won't start, makes squealing noise, or drum doesn't turn. Verify fit.
Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more
Supports and stabilizes the dryer drum for smooth rotation. Replace if you hear squealing, grinding, or the drum moves excessively. Confirm fit with your model.
Dryer won't heat or overheats? A faulty safety thermostat fails to regulate temperature. Test for continuity with a multimeter; moderate DIY repair.
Removed lid. Removed switch panel. Suspected open circuit in thermal fuse. Tested it with a multimeter first to confirm it had an open circuit. This part is obsolete. Contacted manufacturer and found part supercedes to a different part number Ordered part. (This website is very efficient. The part arrived with the 1.7 day promise time.) new fuse bracket is slightly larger due to supercession. Marked bolt hole locations and drilled new. Installed fuse. Re-assembled dryer in reverse order.... Read more
Drum glide supports the front of your dryer drum for smooth rotation. Replace when you hear scraping or squeaking sounds. Confirm fit with your model.
Replaced all wear parts (belt, idler pulley, drum support, glides). Read more
Dryer overheating or shutting down unexpectedly? The high-limit thermostat monitors temperature and cuts power to prevent damage. DIY repair in 30 minutes.
REPLACED BELT AND IDLER. TESTED AND FOUND THERMAL LIMITER BLOWN SO REPLACED IT. DRYER WORKS GOOD Read more
Dryer not heating? This gas igniter lights the burner to produce heat. Replaces worn or non-glowing igniters. Basic repair, about 10 minutes for most DIYers.
Gas valve coils were bad Read more
Dryer overheating or not heating properly? This cycling thermostat regulates temperature by turning the heating element on and off during the cycle.
Dryer drum shaft support with shaft assembly. Replace if drum drops, shaft breaks, or squealing occurs from worn bearings. Verify fit with your model.
Fix a dryer that won't start, advance, or complete cycles with this electromechanical timer. Controls cycle selection and timing. Moderate DIY repair.
Secures the rear drum bearing to keep your dryer drum aligned and rotating smoothly. Replace if bracket is cracked, bent, or worn to restore proper support.
Terminal block mounting screw for dryers and washer dryer combos. Secures the terminal block to the dryer frame. Replace if stripped, missing, or damaged.
Secures the front panel on dryers. Replace if the panel is loose, rattling, or won't stay in place. Confirm fit with your model number before ordering.
Replace missing or stripped pan head screws that fasten dryer panels, brackets, and trim. Standard #8 coarse thread, 3/8-inch length for secure assembly.
Gas supply pipe for dryers. Connects the gas valve to the burner assembly. Replace if cracked, corroded, or leaking to restore safe gas flow to your dryer.