Skip to Content
  • time delivery images 2 Day Quick Delivery!
  • box-refresh images 365 Day Return Policy!
  • lovely images 15 million satisfied customers
  • boxes images Over 2.1 Million Parts In Stock
  • headphone imagesFree Tech Support!
  • google images Google Trusted Store

Search Results

Range Infinite Switch
Genuine Ge part
By: Ge
Part Number: WB24T10162

Fixes burner stuck on high, won't heat, or uneven heating. This infinite switch regulates surface element power for precise temperature control.

Do-It-Yourself Stories from Customers like You Insufficient heat from second and third sections of element   Matt L. • Oviedo , FL • November 27, 2020

Replaced controller. Read more

More
$120.31
Compare At:
$144.37
You Save:
$24.06

IN STOCK
Ships Today Guaranteed
Add to Cart
Cooktop Infinite Switch
Genuine Ge part
By: Ge
Part Number: WB24X10176

Burner stuck on high or won't heat? This infinite switch controls surface element temperature from low to high. Straightforward repair restores heat control.

Do-It-Yourself Stories from Customers like You Surface burner would only heat on high. Broken infinite switch.   Philip J. • University Place , WA • March 17, 2023

We replaced the Infinite Switch. Read more

More
$136.69
Compare At:
$162.12
You Save:
$25.43

IN STOCK
Ships Today Guaranteed
Add to Cart
Refrigerator Door Light Switch
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387911

Fix a refrigerator light that won't turn on or off when you open the door. This push-button switch senses door position. DIY repair in 30 minutes.

This part fixes the following symptoms
  • Light not working
See more...
Do-It-Yourself Stories from Customers like You A failed freezer door switch was causing the fridge to display that the door was open when it was not this caused it to beep at random   Kara H. • Charleston , SC • March 08, 2016

We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND... Read more

More
$27.37
Compare At:
$32.30
You Save:
$4.93

IN STOCK
Ships Today Guaranteed
Add to Cart
Switch
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304511344

The Switch is an OEM component specifically designed for Frigidaire washing machines. It controls various cycle options like water temperature levels, spin speeds, and additional settings like stain removal cycles.

Causes of a bad switch can include water or chemical damage leading to component failure over time, or loose wiring connections causing intermittent issues.  

Symptoms of a bad switch include: 

  • Inability to select wash cycles or adjust settings  
  • Unresponsive or inaccurate temperature levels
  • Lights/displays not functioning as normal
  • Error codes indicating switch problems

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today to avoid expensive repairs down the road.
 

More
$61.56
Compare At:
$73.26
You Save:
$11.70

IN STOCK
Ships Today Guaranteed
Add to Cart
Trash Compactor Drawer Tilt Switch
Genuine Whirlpool part
By: Whirlpool
Part Number: 9871829

Fix a compactor that won't start, stops mid-cycle, or requires holding the pedal down. This drawer tilt switch is a quick 15-second replacement.

Do-It-Yourself Stories from Customers like You Compactor would start sometimes by just closing the door when you start it by normally lifting the pedal it would not stop at the end of it's cycle   Bruce H. • Hewitt , NJ • January 19, 2015

I replaced the upper switch that contacts the door in a closed position and more important the start switch contacted by lifting the start pedal. Read more

More
$50.57
Compare At:
$60.18
You Save:
$9.61

IN STOCK
Ships Today Guaranteed
Add to Cart
Compressor Start Relay
Genuine Frigidaire part
By: Frigidaire
Part Number: 216594300

The Starter is an OEM replacement part for Frigidaire refrigerators. This component is crucial for initiating the compressor, which is responsible for cooling the refrigerator. The starter works by providing the necessary electrical power to get the compressor running, ensuring that the refrigerator maintains the correct temperature.

Causes of a bad starter can include electrical malfunctions, wear and tear over time, or damage from power surges. A faulty starter can prevent the compressor from starting, leading to cooling issues.

Symptoms of a bad Starter include:

  • The refrigerator not cooling properly
  • The compressor not running or frequently cycling on and off
  • Unusual clicking or buzzing noises from the compressor area
  • The refrigerator being warmer than usual or food spoiling quickly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Do-It-Yourself Stories from Customers like You Overload protector done its job we had not defrosted the freezer for a long time causing the compressor to run more than it should it got overloaded found it defrosting   Wanda L. • Belle Rose , LA • December 09, 2014

First checked the power then took off the compresser connections cover looked for burnt wires or loose or disconnected wires they were none of those I then removed the wires from the starter an overload protector removed them checked both for contunuaty overload protector no contunuaty then I checked the 3 poles on the comp. for contunuaty they were ok then I checked each pole to ground on the com. to final check that the comp. was still good Read more

More
$48.95
Compare At:
$58.25
You Save:
$9.30

IN STOCK
Ships Today Guaranteed
Add to Cart
Refrigerator Dispenser Control Switch Assembly
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304525097

Fix water or ice dispenser not working with this 4-button control switch assembly. Common fix when buttons fail to respond or dispense incorrectly.

Do-It-Yourself Stories from Customers like You No water from dispenser.   Steve N. • Malverne , NY • April 10, 2021

Replaced the four-button switch assembly. Read more

More
$77.76
Compare At:
$91.76
You Save:
$14.00

IN STOCK
Ships Today Guaranteed
Add to Cart
Limit Switch
Genuine Whirlpool part
By: Whirlpool
Part Number: WP12575501

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

  • Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
  • Changes state at a defined threshold to protect components and wiring
  • Interrupts power to heat or motor circuits, or signals a control to respond
  • Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation
What's included:
  • 1 limit switch
Install notes:
  • Disconnect power to the appliance before servicing
  • Note wire positions; transfer connectors one at a time or take a photo for reference
  • Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
  • Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

This part fixes the following symptoms
  • Not dispensing water
See more...
Do-It-Yourself Stories from Customers like You Water dispenser quit working   Frank K. • Pass Christian , MS • February 20, 2017

I replaced the switch which was bad and also replaced the water inlet valve. Read more

More
$49.51
Compare At:
$58.92
You Save:
$9.41

IN STOCK
Ships Today Guaranteed
Add to Cart
Resistor
Genuine Whirlpool part
By: Whirlpool
Part Number: 279872

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

  • Provides precise resistance to reduce voltage/current in the designated dryer circuit
  • Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
  • Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
  • Replace if visibly burned/damaged or if testing shows an open or shorted condition
What's included: One resistor Install notes:
  • Disconnect power to the appliance before servicing
  • Access the console/wiring harness and note original wire routing
  • Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
  • After installation, run a test cycle to ensure proper operation of the affected function

Do-It-Yourself Stories from Customers like You Timer wouldn't advance on my dryer   John L. • Oblong , IL • March 22, 2016

I ordered a new timer and installed it with the help of the videos provided and this did not solve my problem so I chated with the pros @ Appliance Parts Pros and told them my problem and they told me the problem and recommended the part I needed and With the incredibly fast shipping I had the part the next day. I installed it and now my dryer timer works great.Thanks to APPs for their help and ease of ordering and fast shipping. I highly recommend AppliancePartPros and will definitely use... Read more

More
$46.35
Compare At:
$55.16
You Save:
$8.81

IN STOCK
Ships Today Guaranteed
Add to Cart
Switch (Control Panel)
Genuine Frigidaire part
By: Frigidaire
Part Number: 316445501

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

  • Directs power to the associated circuit when switched on or off
  • Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
  • Helps restore positive, consistent control from the backguard/control panel
What's included: One switch Install notes:
  • Disconnect power at the breaker before servicing
  • Access the switch from the control panel/backguard; retain screws/clips
  • Label/photograph wire positions and transfer leads one at a time to the new switch
  • Ensure firm terminal connections, reassemble, restore power, and test operation

Do-It-Yourself Stories from Customers like You Oven light would not turn off   Stanley W. • Beaver Creek , OH • December 23, 2016

Replaced the switch Since I was not familiar with this type of socket it would have helped to know the oven had to be pulled out of the cabinet a few inches Read more

More
$73.95
Compare At:
$87.26
You Save:
$13.31

IN STOCK
Ships Today Guaranteed
Add to Cart
Range Surface Burner Infinite Switch
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9763761

If your range burner won't heat, cycles incorrectly, or buzzes when turned on, a faulty infinite switch is likely the cause. Moderately easy DIY repair.

Do-It-Yourself Stories from Customers like You Stems were broken on handles. Knobs didn't work correctly.   Dan R. • Glendale , CA • May 06, 2020

Had to replace both switches. The hard part was getting the control panel off to get access. Only a few screws but even after getting them out, really struggled getting it off. After getting off, discovered that you need to get it lifted up before pulling it off. Read more

More
$142.95
Compare At:
$170.11
You Save:
$27.16

IN STOCK
Ships Today Guaranteed
Add to Cart
Cooktop Igniter Switch
Genuine Ge part
By: Ge
Part Number: WB24K5083

Fix burners that won't spark or click constantly with this igniter switch. Mounts on the gas valve stem to activate spark ignition. Easy 15-minute repair.

This part fixes the following symptoms
  • Won't start
See more...
Do-It-Yourself Stories from Customers like You Clicking from ignitor mode would not stop after burner lit   Jeffrey Maclachlan V. • Nederland , CO • September 03, 2017

Turned out the little switches on the knob shaft had corroded and were staying on. There was constant continuity showing with an ohm meter. Replacing the switches was very easy (always disconnect power to the unit before servicing). Bought a new ignitor module as a backup as they do go out of production after 10 years or so- another cheap and easy fix if needed in the future. Read more

More
$25.61
Compare At:
$30.48
You Save:
$4.87

IN STOCK
Ships Today Guaranteed
Add to Cart
Range Hood Motor And Lamp Switch
Genuine Ge part
By: Ge
Part Number: WB24X10110

Fix a range hood fan that won't turn on or off, or lights that don't respond to controls. This motor/lamp switch restores on/off control. Moderate DIY.

Do-It-Yourself Stories from Customers like You Broken fan switch   William S. • Marco Island , FL • October 02, 2015

Biggest problem was trying to get at the switch to replace it. Had to remove two allen head screws to gain access on the back panel of the range hood. The allen heads were very small fortunately I had a number bits from my old electric screw driver that allowed me to remove them. Even then I had to snake my way cutting my hand to get to the switch to replace it. The positive part the switch was over $25 less the if purchased directly from GE through Appliance Pros. Read more

More
$102.41
Compare At:
$123.54
You Save:
$21.13

IN STOCK
Ships Today Guaranteed
Add to Cart
Gas Cooktop Switch Harness
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4456901

Fix sparking or non-working igniter switches with a new switch harness. Connects control switches to cooktop wiring. Moderate DIY repair, 1-2 hours.

Do-It-Yourself Stories from Customers like You Igniter not working.   Adrian H. • Totowa , NJ • January 18, 2022

Replaced the Spark Module and the Wire Harness. Works like new. Read more

More
$117.54
Compare At:
$141.05
You Save:
$23.51

IN STOCK
Ships Today Guaranteed
Add to Cart
Dishwasher Door Interlock Switch
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10274880

Fix a dishwasher that stops mid-cycle with a blinking start light. This door interlock switch restores reliable operation. 20-minute DIY repair.

Do-It-Yourself Stories from Customers like You Kenmore ultra wash dishwasher worked great for 18 months; then would not run start button blinked 3 times and nothing happened   Nick C. • Safety Harbor , FL • November 12, 2015

Looked online, appeared to be door switch or control panel. Tried door switch first, a $30 part. Installed new door switch and washer started right up and appears to be fixed. Have not tried full wash cycle yet, but problem appears to be fixed. I decided to buy part from AppliancePartsPros.com because I could return the part if it did not correct the problem, no one else offered such a deal. I will only deal with AppliancePartsPros in the future, they were extremely helpful on the phone! Read more

More
$50.57
Compare At:
$60.18
You Save:
$9.61

IN STOCK
Ships Today Guaranteed
Add to Cart
Laundry Center Cycle Selector Switch
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10285512

Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.

Do-It-Yourself Stories from Customers like You Temperature control switch failed to cold only.   Marilyn M. • Summerfield , FL • September 30, 2017

Replaced with a new one. Read more

More
$83.44
Compare At:
$99.29
You Save:
$15.85

IN STOCK
Ships Today Guaranteed
Add to Cart
  • boxes images Over 2.1 Million Parts In Stock
  • time delivery images 2 Day Quick Delivery!
  • box-refresh images 365 Day Return Policy!
  • headphone imagesFree Tech Support!
  • google images Google Trusted Store