Parts for Amana YNED5800DW0: Top And Console Parts

This top panel is the upper cover of your dryer's cabinet. Replace a dented, rusted, or warped panel to restore a secure, flush fit and the clean, finished look of your machine.

• Forms the dryer's upper cabinet surface and covers internal components
• Provides proper mounting/alignment for the control console and top hardware
• Helps maintain cabinet rigidity and a solid, secure fit
• Common signs it's needed: visible dents/bends or rust, top won't sit flush or stay secured, gaps or misalignment near the console

• Disconnect power; shut off gas supply for gas models
• Wear cut-resistant gloves—cabinet edges can be sharp
• Remove fasteners securing the top, lift off, and transfer any clips/insulation from the original panel
• Align the new panel and tighten fasteners evenly to ensure a flush, secure fit

Console shell replaces the dryer's outer control housing to restore a clean, secure surface for the control assembly and controls. It repairs cosmetic damage while providing the proper mounting surface for the control components. What it does:

• Covers and protects the control assembly from impact, dust, and debris.
• Provides the structural mounting surface for knobs, switches and the control interface.
• Common symptoms it addresses: cracked, dented, warped or split console and loose or misaligned controls.
• Restores the dryer's appearance and helps prevent further damage to internal control components.

• Disconnect power (unplug the dryer or shut off the circuit breaker) before beginning any work.
• Removal/installation typically requires removing the dryer top or front panel; basic hand tools (screwdriver, nut driver) are commonly used.
• Handle any sharp sheet-metal edges with care and wear gloves and eye protection.

This round control knob replaces a worn or broken stove/oven control knob to restore precise user control and a finished look. It fits on standard splined valve stems and provides an easy, tactile dial for adjusting settings. What it does

• Turns smoothly to operate temperature or burner valves for ranges and ovens
• Replaces cracked, stripped, or missing knobs that prevent proper control
• Helps stop slip or poor grip when selecting heat levels
• Restores clear pointer alignment for accurate setting selection

• Remove power to the appliance or ensure controls are off before replacing
• Pull the old knob straight off the control shaft; align and push the new knob onto the splined stem until fully seated
• Use moderate force only; do not hammer or modify the shaft or knob
• If the knob does not fit, double-check the appliance model and shaft type

The Wire Harness is an OEM part for Whirlpool dryers. This wire harness is responsible for delivering power and electricity throughout the dryer and to its individual components. 

Causes of a bad wire harness can include fraying or exposed wires due to wear and tear over time, cracking or damage of protective casings that expose internal wirings, or malfunctioning connections that disrupt power flow.

Symptoms of a bad wire harness include:

• The dryer not starting or powering on
• Components like the drum or heating elements not working
• Buzzing or humming noises coming from inside the dryer
• Tripped or blown fuses
• Error codes or failure to progress through cycles properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.