Parts for Whirlpool WED6620HW0: Top And Console Parts

This top panel is the upper cover of your dryer's cabinet. Replace a dented, rusted, or warped panel to restore a secure, flush fit and the clean, finished look of your machine.

• Forms the dryer's upper cabinet surface and covers internal components
• Provides proper mounting/alignment for the control console and top hardware
• Helps maintain cabinet rigidity and a solid, secure fit
• Common signs it's needed: visible dents/bends or rust, top won't sit flush or stay secured, gaps or misalignment near the console

• Disconnect power; shut off gas supply for gas models
• Wear cut-resistant gloves—cabinet edges can be sharp
• Remove fasteners securing the top, lift off, and transfer any clips/insulation from the original panel
• Align the new panel and tighten fasteners evenly to ensure a flush, secure fit

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

This bracket is a small mounting support that secures appliance panels or components in place to restore stable alignment and reduce rattling. It's a direct-fit replacement that helps keep parts properly positioned for reliable operation. What it does:

• Provides a secure mounting point for a panel or internal component to prevent shifting or vibration
• Restores correct alignment for doors, panels, or assemblies that have become loose
• Helps eliminate rattling, buzzing, or scraping noises caused by a loose support
• Maintains proper spacing so attached components operate smoothly

• Verify appliance is unplugged or power is disconnected before starting work
• Inspect mounting area and fasteners; replace any damaged screws or clips as needed
• Use basic hand tools to remove and reinstall the bracket; avoid overtightening

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Console is an OEM replacement part for Whirlpool electric dryers. It is the plastic enclosure that houses the digital cycle and temperature interface.

Causes of a faulty console can include moisture damage and compromising internal electronics. Standard usage stress from opening and closing the dryer door over time can also weaken plastic integrity. 

Symptoms of a failing console include:

• Erratic button responses or uncalibrated display readings  
• Visibility issues like fading or ghosting on the screen
• Inability to activate heat settings or drying cycles
• Loose attachment points causing misalignment

This genuine OEM Whirlpool console is also compatible with electric dryer models from Maytag, KitchenAid, Jenn-Air, and Kenmore.

This wire harness routes power and signals between the appliance's controls and components, restoring proper electrical connections for reliable operation. Replace a damaged or burned harness to fix intermittent or lost power and unresponsive controls. What it does

• Connects control board, switches and sensors so components receive power and signals
• Replaces frayed, melted or damaged wiring that can cause intermittent faults
• Helps resolve symptoms like controls not responding, lights or motors failing to start, or erratic operation
• Maintains correct wire routing and connector fit to prevent electrical shorts

• Disconnect power and, for gas models, turn off gas supply before starting any repair
• Handle connectors carefully; match connector shapes and pin count when reinstalling
• Route the harness along original clips and channels to avoid heat or pinch points

This name plate is the appliance identification label that displays model, serial and rating information and restores the unit's factory appearance. It helps ensure readable identification for service or resale. What it does

• Replaces a missing, faded or damaged identification label so model and serial info are visible.
• Provides required equipment ratings and manufacturer markings used during diagnostics and parts replacement.
• Restores exterior appearance where the original name plate is worn or peeling.
• Helps technicians and homeowners quickly confirm appliance identity during repairs.

• Name plate (single label)

• Disconnect power to the appliance before attempting installation or working near electrical connections.
• Clean and dry the mounting area; some name plates attach with adhesive while others fasten with screws—use the original hardware if present.
• Avoid bending or creasing the label when aligning it; press firmly to ensure full contact for adhesive-mounted plates.