Parts for Whirlpool WHD560CHW2: Top And Console Parts

This top panel is the upper cover of your dryer's cabinet. Replace a dented, rusted, or warped panel to restore a secure, flush fit and the clean, finished look of your machine.

• Forms the dryer's upper cabinet surface and covers internal components
• Provides proper mounting/alignment for the control console and top hardware
• Helps maintain cabinet rigidity and a solid, secure fit
• Common signs it's needed: visible dents/bends or rust, top won't sit flush or stay secured, gaps or misalignment near the console

• Disconnect power; shut off gas supply for gas models
• Wear cut-resistant gloves—cabinet edges can be sharp
• Remove fasteners securing the top, lift off, and transfer any clips/insulation from the original panel
• Align the new panel and tighten fasteners evenly to ensure a flush, secure fit

This bracket is a small mounting support that secures appliance panels or components in place to restore stable alignment and reduce rattling. It's a direct-fit replacement that helps keep parts properly positioned for reliable operation. What it does:

• Provides a secure mounting point for a panel or internal component to prevent shifting or vibration
• Restores correct alignment for doors, panels, or assemblies that have become loose
• Helps eliminate rattling, buzzing, or scraping noises caused by a loose support
• Maintains proper spacing so attached components operate smoothly

• Verify appliance is unplugged or power is disconnected before starting work
• Inspect mounting area and fasteners; replace any damaged screws or clips as needed
• Use basic hand tools to remove and reinstall the bracket; avoid overtightening

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

This wire harness routes power and signals between the appliance's controls and components, restoring proper electrical connections for reliable operation. Replace a damaged or burned harness to fix intermittent or lost power and unresponsive controls. What it does

• Connects control board, switches and sensors so components receive power and signals
• Replaces frayed, melted or damaged wiring that can cause intermittent faults
• Helps resolve symptoms like controls not responding, lights or motors failing to start, or erratic operation
• Maintains correct wire routing and connector fit to prevent electrical shorts

• Disconnect power and, for gas models, turn off gas supply before starting any repair
• Handle connectors carefully; match connector shapes and pin count when reinstalling
• Route the harness along original clips and channels to avoid heat or pinch points

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Control Panel is an OEM part for Whirlpool dryers. It features a display screen, buttons, and controls that allow you to select different drying cycles, adjust temperature settings, and customize options such as timed drying or sensor drying.

A bad control panel can occur due to wear and tear, electrical malfunctions, or damage from accidental impact. If you notice symptoms such as unresponsive buttons, error messages on the display, or the control panel not functioning correctly, it may be time to replace this part.

Symptoms of a bad user interface control panel include:

• Unresponsive buttons
• Error messages on the display
• Control panel not functioning correctly

Restore your Whirlpool dryer by replacing the faulty or damaged control panel with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This name plate is the appliance identification label that displays model, serial and rating information and restores the unit's factory appearance. It helps ensure readable identification for service or resale. What it does

• Replaces a missing, faded or damaged identification label so model and serial info are visible.
• Provides required equipment ratings and manufacturer markings used during diagnostics and parts replacement.
• Restores exterior appearance where the original name plate is worn or peeling.
• Helps technicians and homeowners quickly confirm appliance identity during repairs.

• Name plate (single label)

• Disconnect power to the appliance before attempting installation or working near electrical connections.
• Clean and dry the mounting area; some name plates attach with adhesive while others fasten with screws—use the original hardware if present.
• Avoid bending or creasing the label when aligning it; press firmly to ensure full contact for adhesive-mounted plates.

This wire harness connects the appliance's control components to its power and internal modules, restoring electrical pathways for reliable operation. Designed as a direct-fit replacement to restore proper control and sensor communication. What it does:

• Routes power and signal connections between the main control board and console/components
• Replaces damaged, frayed, or corroded wiring that can cause intermittent operation or failures
• Helps resolve symptoms like no power to controls, unresponsive console, or intermittent cycles
• Maintains factory routing and connector fit for correct electrical continuity

• One wire harness assembly

• Always disconnect power (unplug or shut off breaker) before starting repairs
• Verify connectors align and seat fully; do not force mismatched plugs
• Inspect mounting clips and routing to avoid pinching or chafing when reassembling

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed