Parts for Frigidaire CGIF3036TFA: Top / Drawer Parts

This interior refrigerator liner replaces a damaged or worn cabinet surface to restore a clean, smooth interior and support shelves and drawers. It helps maintain a sanitary storage area and a proper fit for accessories. What it does:

• Provides a smooth, easy-to-clean interior surface for the fresh food compartment
• Restores mounting surfaces for shelves, bins and trim pieces
• Prevents drafts and moisture intrusion where cracks or gaps exist
• Addresses symptoms like visible cracks, gouges, or a warped/loose interior liner

• One refrigerator interior liner

• Disconnect power to the appliance before beginning any repair
• Removal typically requires taking out shelves, trim and fasteners to access the liner
• May require adhesive, clips or screws specific to the model—keep original fasteners and hardware

The Panel is an OEM part for Frigidaire ranges. It is the outer panel that covers and protects the bottom storage drawer, giving your range a finished look.

A bad panel can be caused by wear and tear, damage, or improper handling. Signs of a faulty outer panel include cracks, dents, or discoloration, diminishing the aesthetic appeal of your range.

Symptoms of a bad panel can include:

• Cracks, dents, or scratches on the surface
• Discoloration or fading of the panel
• Loose or unstable panel

Replace your damaged or worn-out panel with this genuine OEM part to restore your range. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This mounting bracket secures internal components to maintain proper alignment and reduce movement in compatible Frigidaire appliances. It replaces a worn or broken bracket to help stop rattling and restore stable part positioning. What it does

• Provides a secure mounting point for internal components to prevent shifting or sagging
• Restores alignment that can cause rubbing, vibration, or noise when a bracket fails
• Helps ensure attached parts operate correctly by maintaining correct positioning
• Commonly replaced when a broken or bent bracket causes loose parts or unusual sounds

• Disconnect power (and water if applicable) before attempting repairs
• Basic hand tools required; may need panel removal to access bracket location
• Reuse existing fasteners unless replacements are specified by the OEM
• Do not over-tighten screws; ensure bracket is seated and aligned before final torque

The Rear Drawer Glide is an OEM part for Frigidaire ranges and ovens. This part is mounted on the rear end of the oven drawer, facilitating a smooth glide when the drawer is opened and closed. It ensures the stability and alignment of the drawer, preventing it from tilting or sticking during use.  

Causes of a bad Rear Drawer Glide can include physical wear and tear from regular use, accidental damage, or degradation of the material over time. Regular inspection and maintenance can help identify issues early and extend the life of the glide.

Symptoms of a bad Rear Drawer Glide include:

• The oven drawer sticking or jamming when opened or closed
• The drawer sagging or not closing properly
• Unusual noises coming from the drawer due to misalignment
• Difficulty in smoothly operating the drawer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This bake element is the oven heating element that provides the heat for baking and roasting so food cooks evenly. It replaces a damaged or faulty oven element to restore normal oven heat. What it does:

• Heats the oven cavity during bake cycles to reach and maintain set temperatures
• Commonly used when the oven doesn't heat or takes too long to preheat
• Can cause uneven cooking or undercooked food if damaged or burned out
• Works as the primary lower heating element in electric ranges and wall ovens

• One bake element assembly

• Disconnect power to the appliance before starting any repair to avoid shock
• Allow the oven to cool completely; use gloves to protect hands from sharp edges
• You may need to remove oven racks and the back or lower access panel for installation
• Secure mounting before restoring power and testing the oven

The Element Assembly is an OEM component specifically designed for Frigidaire brand electric ranges. Located beneath the cooktop surface, these resistive elements generate heat for cooking.

Prolonged use causes elements to warp, crack, or lose continuity over time due to normal heating/cooling cycles. Element failure limits cooktop functionality.

Causes of a faulty element relate to typical wear expected of high-temperature filament windings. Accidental damage during cleaning can also impact integrity.

Symptoms involve:

• One or more cooktop zones not heating properly or at all  
• Burned residue indicating heating dysfunction
• Visible cracks or separations in the resistive coils

Replacing with this OEM Frigidaire assembly restores reliable and consistent zoned heating. Compatibility extends to some Kenmore, Gibson, and Electrolux ranges.

This smooth top cooktop glass assembly replaces a cracked or damaged cooktop surface to restore a flat, easy-to-clean cooking area and proper cookware contact. It fits select electric range models and restores appearance and function. What it does:

• Covers and protects the range's heating elements while providing a smooth cooking surface
• Restores even cookware contact for efficient heating when the underlying elements are working
• Helps prevent debris from falling into the range cavity and simplifies cleanup
• Commonly used when the glass is cracked, chipped, or heavily scratched

• Handle with care; glass can be heavy and break if dropped — use gloves and eye protection
• Verify power is disconnected at the breaker before starting any work
• Installation usually requires removing the range top trim and disconnecting wiring to access mounting points; follow OEM instructions
• If underlying heating elements or supports are damaged, replace them as needed for safe operation

A replacement hinge bracket that secures and aligns the refrigerator door, restoring proper pivot and fit for smooth opening and closing. Install this bracket to correct sagging or misaligned doors and improve door seal performance. What it does

• Secures the door hinge to the cabinet and supports door weight — use when the door droops or hangs unevenly.
• Maintains pivot alignment so the door opens and closes smoothly without binding.
• Helps keep the door gasket aligned for a tighter seal; can reduce uneven gaps and cold-air loss.
• Replaces bent, cracked, or worn hinge-mounting points that cause noise or instability.

• One hinge bracket.

• Disconnect power to the appliance before starting work and remove or support the door to prevent injury.
• Support the door while removing and installing the bracket; a second person may be needed for large doors.
• Reuse existing hinge hardware if undamaged; replace fasteners if stripped or missing.
• After installation, check door alignment and adjust hinge position as needed for a proper seal.

This ignition generator creates the high-voltage pulses that light the surface burners on a gas cooktop or range. Replacing a failed module restores fast, consistent spark ignition and stops unreliable or constant clicking. What it does:

• Converts line voltage into rapid high-voltage sparks sent to the burner electrodes
• Coordinates spark output when a burner knob is turned to Lite
• Common symptoms: no spark/click, intermittent or weak spark, only some burners ignite, or continuous clicking after flame is present
• Helps ensure reliable burner lighting and consistent performance

• One spark ignition module assembly

• Disconnect power and shut off gas before servicing
• Label and transfer wires one at a time; route leads away from heat and sharp edges
• Mount securely and ensure a good ground connection for proper sparking
• High voltage hazard—do not touch terminals or test with power applied

This mounting bracket secures internal components and panels so the appliance stays stable and aligned. Replacing a worn or broken bracket restores proper support and reduces rattling or misalignment. What it does:

• Provides structural support for internal panels, assemblies, or trim
• Holds components in correct position to prevent rubbing or vibration
• Stops movement that can cause noise, wear, or improper door/panel alignment
• Helps maintain safe operation by keeping parts securely fastened

• Disconnect power before starting any repair to avoid electrical shock
• Use basic hand tools; keep fasteners and orientation noted for reassembly
• Inspect surrounding clips, screws, and mounting points; replace any damaged hardware

The Handle is an OEM part for Frigidaire ranges. Crafted from durable heat-resistant metal, these handles provide safe, ergonomic access to oven interiors during cooking cycles.  

Prolonged exposure to elevated oven temperatures causes typical discoloration of painted finishes as well as looseness from load stresses reducing tactile control over years. Cooking convenience decreases without gripable surfaces.

Symptoms indicating handle wear include:

• Faded, chipped, or flaking handle finishes  
• Loose, rattling, or awkward movement from placement
• Deteriorating mounting attachments risking accidental falls

Replacing with this OEM Frigidaire handle restores tactile guidance into the cooking cavity. Compatibility also fits some Kenmore, Electrolux, and Gibson ranges renewing secure doorknob function through authorized maintenance. 

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

This factory screw secures components in your appliance, restoring a tight, rattle-free fit. Replace missing or damaged hardware to keep panels, brackets, and trim properly fastened and aligned for safe, reliable operation.

• Secures panels, brackets, trim, or internal components to the chassis
• Replaces lost, rusty, stripped, or cross-threaded screws
• Helps eliminate looseness, gaps, and vibration/rattling
• Common signs: loose/misaligned panels or trim, rattling noises, missing or rounded screw heads

• Disconnect power (and shut off gas if applicable); allow the unit to cool completely
• Match to the original location and replace one at a time to maintain alignment
• Hand-start to prevent cross-threading; tighten snugly—do not overtighten
• Use light torque when threading into plastic or thin sheet metal

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.