Parts for Ge WCVH4815K0MS: 04 - Tub & Motor Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

Damper shock (60N) for washers. This shock absorber steadies the outer tub during spin to reduce vibration and noise. Replacing a weak damper restores smoother operation and helps prevent the basket from banging the cabinet. What it does:

• Mounts between the outer tub and base to absorb movement
• Controls vibration for a stable spin cycle
• Worn or broken dampers can cause loud banging/thumping, excessive shaking, or the washer "walking"
• Visual clues of failure may include cracked ends, loose mounts, or oil residue on the shock body

• Disconnect power and shut off water before servicing
• Remove the appropriate access panel(s) and support the tub to relieve tension on the shock
• Match the original orientation and transfer any brackets or hardware as needed
• After installation, hand-move the tub to verify smooth travel; consider replacing all shocks together for balanced damping

A right-side counter weight that restores proper door balance and alignment for compatible refrigeration units. Replaces a worn or missing weight to help doors open, close and stay aligned as designed. What it does:

• Balances the door to prevent sagging or uneven gaps
• Helps the door close fully and maintain a consistent seal
• Restores smooth, predictable door movement after weight loss or damage
• Works with the factory mounting locations and fastening method

• Install with power off and empty door storage to reduce strain and risk
• Use the factory mounting hardware and torque to manufacturer guidance
• Check door alignment and seal after install; adjust hinges if needed
• If the weight or hardware is damaged, replace both for best alignment

The Door Gasket is an OEM part for GE washing machines. Located around the washer door opening, it creates a tight seal during cycles to prevent water leaks.   

Symptoms of a bad door gasket include:

• Water leaks from the washer door opening  
• Excess moisture buildup or puddling near the door
• Inability to achieve proper seal for optimal washing

Causes for failure can be cracks, perforations, or deteriorated material from repeated use and mechanical stresses over time. Mineral or soap deposits may also degrade sealing properties.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This tub front is the front bulkhead that supports the dryer drum and front drum seal, restoring proper drum alignment and helping reduce rubbing, squeaks, and wear on rotating components. What it does:

• Supports the dryer drum at the front and provides a mounting surface for the front drum seal.
• Keeps the drum centered to allow smooth, even tumbling.
• Prevents clothes from catching or rubbing on the cabinet by maintaining correct drum clearance.
• Commonly replaced when the front surface is cracked, warped, or the seal area is damaged, causing noise or rubbing.

• One tub front (front bulkhead) as shown.

• Disconnect power to the appliance before starting any repair.
• Replacement typically requires removing the dryer front panel and drum; keep fasteners and note seal orientation.
• Use basic hand tools; some models may require lifting the drum slightly to set the tub front.
• If seals, bearings, or felt guides are worn, replace them at the same time for best results.

This tub seal fits between the dryer drum and bulkhead to help keep warm air in the drum and prevent lint and moisture from entering the cabinet. Restores a proper drum-to-bulkhead seal for more consistent drying. What it does:

• Seals the gap between the drum and tub/bulkhead to maintain airflow and drying efficiency
• Helps prevent lint buildup and moisture from entering the dryer cabinet
• Reduces rubbing and wear on the drum edge and adjacent components
• Addresses common symptoms like excessive noise, rubbing sounds, or poor drying due to air loss

• One tub seal (single seal as shown)

• Only install on compatible models and with the dryer disconnected from power; unplug or switch off breaker before starting
• Replace any damaged clips or fasteners and inspect the drum and bulkhead for wear during installation
• Use basic hand tools; avoid forcing the seal—ensure proper seating around the drum for an even fit

This tub rear assembly replaces the dryer drum's rear support and seal to restore proper drum alignment and airflow. It helps reduce rubbing noises and prevents air leaks that can affect drying performance. What it does

• Supports the drum's rear edge and maintains correct drum rotation alignment
• Houses the rear drum seal and helps direct airflow through the drum
• Reduces metal-on-metal rubbing, squeaks, and unusual rear-drum noises
• Helps prevent exhaust air leaks that can lengthen dry times or lead to hot spots

• One tub rear assembly as shown

• Recommended for installers or experienced DIYers; follow your appliance's service manual
• Disconnect power before beginning any repair
• Inspect adjoining seals, rollers, and fasteners while the unit is open and replace if worn
• Reassemble panels and verify proper drum rotation and spin before returning the dryer to service

This basket assembly is a genuine OEM replacement part sourced directly from the manufacturer for use in front-load washing machines. This assembly is part of the washer's drive system. It is on top of the clutch and transmission system. It contains the spin tube shaft and brake system for the spin basket. If the washing machine is making loud noises during the spin cycle or won't spin at all, the basket assembly should be replaced. A screwdriver, socket wrench set and ratchet, hammer, and spanner wrench are needed to make this repair. Disconnect the water and power to the washing machine. Wear work gloves when making these repairs. Make sure the machine is pulled away from the wall, and there is plenty of room to work while disassembling the machine. Remove the top console and then the washing machine cabinet. Take the tub ring and agitator off the machine. Remove the spin basket and drive block and release the drive block. Remove and replace the basket drive. Reverse the order and reassemble the washing machine. Reconnect the power and water. This basket assembly is sold individually. It is designed for washing machines manufactured by General Electric.

This is a replacement M6.5 × 25 mm machine screw used to secure panels and components on compatible appliances. It restores proper fastening where a missing or damaged screw causes loose parts or poor alignment. What it does:

• Secures panels, brackets, or assemblies that use an M6.5 × 25 mm fastener
• Stops rattling or vibration caused by a missing or stripped screw
• Restores proper component alignment for doors, panels, or internal mounts
• Matches OEM thread size and length for a direct-fit replacement when specified

• Disconnect power and, if applicable, water before servicing the appliance
• Use the correct driver or socket to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not over-torque
• If the original mounting hole or threads are damaged, repair or replace the mating part before installing

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This heater thermistor is a temperature-sensing replacement part that helps the appliance monitor and regulate heating. Replacing a failed thermistor restores accurate temperature feedback for safer, more consistent operation. What it does

• Measures temperature near the heater and sends a signal to the control board.
• Helps the unit cycle heating on and off to maintain proper operating temperature.
• Common symptom: appliance won't heat or heats intermittently.
• Common symptom: cycles too frequently or shows error codes related to temperature sensing.

• One heater thermistor.

• Disconnect power before accessing or replacing the thermistor.
• Handle the sensor and connector carefully to avoid damage to the lead or plug.
• Verify connector orientation and secure wiring; do not force connectors.

A small retaining clamp used to secure hoses, tubing, or small assemblies so they stay in place and maintain proper routing. Keeps connections snug to reduce movement and noise for reliable appliance operation. What it does

• Secures hoses, tubes or wiring looms to prevent slipping or chafing
• Helps maintain proper routing and alignment of components
• Reduces vibration-related noise from loose parts
• Can prevent intermittent connection issues caused by loose fittings

• One clamp

• Turn power off and disconnect the appliance before servicing
• Access the clamp location
• Use appropriate pliers or screwdriver for removal and installation to avoid damaging nearby parts
• Replace with the correct OEM clamp size and orientation; do not overtighten

This packing thermistor is a temperature sensor that mounts in the refrigerator/freezer door gasket to help the appliance monitor temperatures near the door seal for more accurate temperature control and efficient cooling. What it does:

• Senses temperature at the door gasket so the control board can adjust cooling and defrost cycles
• Helps prevent false warm readings caused by door-area drafts or melting frost
• Common symptoms when failing: inconsistent fridge/freezer temperatures, longer run cycles, or temperature-related error codes
• Works as the sensor input for system diagnostics and control logic

• One packing thermistor sensor

• Disconnect power to the appliance before replacing any parts
• Handle the sensor and its wiring gently to avoid damaging the lead or connector
• Route and secure the lead so it isn't pinched by the gasket when reinstalling the door

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.