Parts for Kitchenaid KUDF204KSB00: Upper Drawer Parts

This replacement drawer front restores the visible face and fit of a damaged or worn refrigerator/freezer drawer, improving appearance and allowing the drawer to open and close properly. What it does:

• Replaces a cracked, faded, or dented drawer front to restore cabinet appearance
• Provides the mounting surface and edges that mate with the drawer bin and slide hardware
• Helps the drawer seal and align so the drawer operates smoothly
• Fixes issues where the drawer front is loose, broken, or warped and interferes with normal use

• High-level swap: remove the drawer/bin per your model instructions, detach old front, and fasten the replacement using existing clips or screws
• Keep fasteners and mounting clips organized for reassembly; confirm orientation before tightening
• Disconnect power to the appliance or unplug the refrigerator if accessing electrical components nearby, and follow manufacturer safety guidance
• Use gloves to protect hands from sharp edges and avoid dropping the panel to prevent cosmetic damage

This mat is a replacement cabinet/insulation piece that helps protect the appliance base and reduce vibration transfer to surrounding cabinetry or flooring. It restores the original fit and helps maintain stable operation and finish protection. What it does:

• Cushions the appliance base to reduce rattling or vibration felt during operation
• Helps protect flooring and cabinet surfaces from scuffs and wear
• Provides a barrier that can assist with minor insulation/airflow spacing under the unit
• Can reduce noise caused by direct contact between the appliance and surrounding cabinetry

• One replacement mat as shown

• Disconnect power and move the appliance per the manufacturer's safety guidance before accessing the base area
• Slide or lift the old mat out and position the new mat in the same orientation; no special tools are typically required
• Ensure the mat sits flat and does not interfere with leveling legs, vents, or wiring

This replacement mounting screw secures appliance panels and components so parts stay aligned and stable during use. A simple, direct fastener that restores proper fit and prevents rattling or loose trim. What it does

• Secures panels, brackets, or trim to the appliance frame
• Restores proper alignment and prevents vibration or rattling noises
• Keeps parts from shifting, reducing wear on connected components
• Works wherever the original screw was used to hold assemblies in place

• Disconnect power and/or water before accessing internal components
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep track of removed fasteners and replace like-for-like for best fit

This door gasket seals the refrigerator/freezer compartment to help maintain consistent internal temperatures and reduce moisture build-up. It replaces a worn or torn seal to help keep food fresher and minimize frost at the door. What it does:

• Creates an airtight seal between the door and cabinet to help maintain proper cooling
• Helps prevent warm air and moisture from entering the compartment
• Commonly replaced for symptoms like visible cracks, tears, gaps, or persistent frost buildup
• Can reduce excessive run-time caused by a failing door seal

• Disconnect power to the appliance before starting any repair
• Remove the old gasket by loosening the door trim or pulling it out of the retainer as applicable
• Press the new gasket evenly into the channel or reattach trim, ensuring full contact around the entire door edge
• Warm the gasket (hair dryer or warm water) if needed for flexibility and to improve final sealing; check for gaps after installation

This display is the user interface assembly that shows settings, time and status so you can operate your appliance and read cycle information at a glance. It replaces a cracked, unresponsive, or blank control display. What it does:

• Shows cycle status, time, and selection indicators.
• Communicates with the control board to display error codes and alerts.
• Restores visible feedback when characters are dim, missing, or scrambled.
• Stops misleading or no-display symptoms caused by a failed front display.

• One display/user interface assembly as pictured.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock.
• Remove the control console or trim per your model's instructions to access the display.
• Handle the display and ribbon/connectors gently to avoid damage; secure all connectors before testing.