Parts for Frigidaire SM230MXW2: 02 - Cabinet Parts And Heater Parts

Secure hose clamp for dishwashers. Replace if hoses are loose, leaking, or clamp shows wear or corrosion. Verify fit with your model number before ordering.

Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.

Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.

Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.

White exhaust cover for washer dryer combo units. Replaces cracked, discolored, or missing exhaust caps. Installs on the exterior vent outlet.

Replacement mounting screw for washers. Secures panels, brackets, or components inside your washer. Order when original screws are stripped or missing.

Rubber grommet cushions washer lid to reduce noise and prevent scratching. Replace when worn, cracked, or missing to restore proper lid alignment.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.

This part has been discontinued by the manufacturer and is no longer available.

Leveling foot for dryers. Attaches to the bottom corner of the cabinet to stabilize and level the unit. Replace if cracked, broken, or missing.

Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.

Drive coupling for washer dryer combo units. Connects the motor to the transmission. Replace if cracked, worn, or broken to restore proper operation.

Secures the drum baffle (lifter vane) to your washer drum. Replace missing, stripped, or loose screws to keep baffles firmly attached and prevent rattling.

Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.

This screw is a small fastener used to secure appliance components and trim so panels and parts stay in place. It replaces missing or damaged screws to restore secure assembly and reduce rattling or loose pieces. What it does:

• Fastens panels, brackets, trim, and small components to the appliance frame
• Restores secure mounting when original screws are missing, stripped, or damaged
• Helps stop vibration-related noise from loose parts
• Matches the OEM thread and head style for a proper fit when replacing the original screw

• Disconnect power and water before accessing internal panels or electrical areas
• Use the correct driver bit to avoid stripping the screw head
• Do not overtighten — snug until secure to avoid damaging threads or parts
• If replacing multiple screws, verify each screw matches length and head style before installing

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Dryer won't start or heat? A blown thermal fuse is the most common cause. This safety component cuts power when overheating occurs. DIY repair in 30 minutes.

Door strike plate for washer dryer combo units. Secures the door latch mechanism to the cabinet frame. Replace if cracked, bent, or missing.

Rubber suspension bushing for washer drum support. Replaces worn or cracked bushings that cause noise and vibration. Installs on suspension rods.

This cable tie secures wiring and small hoses inside the appliance to prevent rubbing, snagging, and vibration-related movement. It's a simple replacement part for restoring proper wire routing and keeping components tidy and safe. What it does:

• Holds wiring harnesses and loose cables in place to reduce wear and chafing
• Helps prevent wiring from contacting hot or moving parts
• Reduces noise caused by loose wires or hoses
• Keeps connectors and lines routed for reliable operation

• Disconnect power to the appliance before servicing
• Route wiring as shown in the appliance wiring diagram or photos, then cinch the tie snugly—do not overtighten
• Trim excess tail and ensure the tie does not stress the wire insulation
• Replace any damaged wiring or insulation discovered during installation

Secure hose clamp for dishwashers. Replace if hoses are loose, leaking, or clamp shows wear or corrosion. Verify fit with your model number before ordering.

Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.