Parts for Frigidaire DE400KDD4: 04 - Console And Control Parts

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

This is a replacement mounting screw used to secure a solenoid valve or solenoid assembly in appliances. It provides a durable fastening point so the solenoid stays properly positioned and functions reliably. What it does:

• Secures solenoid valves or solenoid assemblies to the appliance frame or bracket
• Helps maintain correct alignment for valve operation and connections
• Prevents loosening from vibration or normal use
• Suitable where the OEM fastener is required for a proper fit

• Use the matching screw size and thread pattern listed in the appliance parts diagram
• Tighten to snug only; overtightening can strip threads or damage the solenoid housing
• Disconnect power and shut off water before servicing the appliance
• If other fasteners or damaged components are present, inspect and replace as needed

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

This part has been discontinued by the manufacturer and is no longer available.

This ground wire provides a secure electrical ground connection for your appliance's chassis to help prevent electrical shock and ensure safe operation. It replaces a damaged or missing grounding lead. What it does:

• Connects the appliance chassis to the grounding point to safely dissipate stray current
• Restores proper grounding after corrosion, fraying, or accidental damage
• Helps eliminate intermittent electrical faults caused by a poor ground
• Works where a single grounding lead is required for the component or cabinet

• One ground wire

• Turn off and unplug the appliance (or disconnect power at the breaker) before starting any work
• Verify the original grounding point and wire routing before removal to match reinstallation
• Use appropriate tools to remove and reinstall fasteners; ensure tight, clean metal-to-metal contact