Parts for Frigidaire WRT17CVAZ2: 03 - Cabinet, Fan Assembly Parts

Round control knob for air conditioners, freezers, and refrigerators. Replaces cracked, broken, or missing knobs. Restores precise temperature control.

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

This fan motor mounting bushing is used in refrigerator fan motor assemblies to prevent vibrations between the fan motor and the surrounding components. Over time, the rubber on the bushing may become cracked or broken and fall off. Loud noises coming from the refrigerator's freezer section where it is mounted are a good indicator that the bushing needs to be replaced. To start, disconnect the refrigerator's power and empty the refrigerator and freezer's contents into an ice chest to keep them cold until the motor mount bushing is replaced. Open the freezer door and remove the plastic access panel on the back wall; the fan blade and motor are located behind it. Gently pull the fan blade off the center post. Remove the screws holding the motor in place and remove the motor. Take the old bushing off and install the new bushing. Replace the panel. Put the food contents back inside the freezer and refrigerator and restore the power.This motor mounting bushing is an authentic OEM replacement part sourced directly from the manufacturer. It is sold individually. It is designed for use in refrigerators manufactured by Frigidaire, Kenmore, Gibson, and Kelvinator.

Fix a loose or vibrating trimmer motor with this front motor mounting bracket. Secures the motor assembly to the housing. Easy 15-minute repair.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

This evaporator fan motor circulates cold air across the freezer evaporator coil so your refrigerator cools evenly and runs efficiently. Replacing a failed motor restores airflow to reduce warm spots and frost buildup. What it does:

• Spins the evaporator fan to move cold air through the freezer and fresh food sections
• Helps maintain consistent internal temperature for proper food preservation
• Stops noisy operation when the motor bearings fail or the motor becomes unbalanced
• Fixes no-airflow symptoms such as warm compartments or excessive frost on the evaporator

• Disconnect power before starting and wear hand protection for sharp sheet metal or fins
• Access usually requires removing the freezer evaporator cover and disconnecting the wiring harness
• Keep wiring connections secure and verify proper blade direction and clearance before reassembling
• Test operation after restoring power; stop and re-check if unusual noise or vibration occurs

Replace a cracked or broken motor mounting bracket causing excessive vibration or motor misalignment. Simple hand tool installation in 15-20 minutes.

White plastic button plug that covers unused hinge holes on refrigerator doors. Replace if cracked, missing, or discolored for a clean finished look.

Center hinge pin that secures and aligns the middle door hinge on your refrigerator. Replace when worn, damaged, or missing to restore door support.

Replaces cracked or missing cabinet corner trim on your freezer. Covers exposed edges where two panels meet, restoring a finished look and alignment.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

Lower hinge pin secures the refrigerator door to the cabinet, acting as the pivot point. Replace if worn, damaged, or broken to restore smooth operation.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

Secures panels, brackets, and handles in refrigerators and other appliances. Replace missing or stripped screws to restore secure mounting.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Replaces a worn, cracked, or missing push-cap on your refrigerator's control panel. Restores the protective cover over switches and buttons.

White touch-up paint for refrigerators and appliances. Covers scratches, chips, and minor cosmetic damage on exterior surfaces. 0.6 fl oz bottle.