Parts for Frigidaire RT173GCW2: 03 - Cabinet, Shelves, Divider, Fan Asse Parts

Replace a cracked or broken motor mounting bracket causing excessive vibration or motor misalignment. Simple hand tool installation in 15-20 minutes.

This fan motor mounting bushing is used in refrigerator fan motor assemblies to prevent vibrations between the fan motor and the surrounding components. Over time, the rubber on the bushing may become cracked or broken and fall off. Loud noises coming from the refrigerator's freezer section where it is mounted are a good indicator that the bushing needs to be replaced. To start, disconnect the refrigerator's power and empty the refrigerator and freezer's contents into an ice chest to keep them cold until the motor mount bushing is replaced. Open the freezer door and remove the plastic access panel on the back wall; the fan blade and motor are located behind it. Gently pull the fan blade off the center post. Remove the screws holding the motor in place and remove the motor. Take the old bushing off and install the new bushing. Replace the panel. Put the food contents back inside the freezer and refrigerator and restore the power.This motor mounting bushing is an authentic OEM replacement part sourced directly from the manufacturer. It is sold individually. It is designed for use in refrigerators manufactured by Frigidaire, Kenmore, Gibson, and Kelvinator.

This fan motor mounting bushing is used in refrigerator fan motor assemblies to prevent vibrations between the fan motor and the surrounding components. Over time, the rubber on the bushing may become cracked or broken and fall off. Loud noises coming from the refrigerator's freezer section where it is mounted are a good indicator that the bushing needs to be replaced. To start, disconnect the refrigerator's power and empty the refrigerator and freezer's contents into an ice chest to keep them cold until the motor mount bushing is replaced. Open the freezer door and remove the plastic access panel on the back wall; the fan blade and motor are located behind it. Gently pull the fan blade off the center post. Remove the screws holding the motor in place and remove the motor. Take the old bushing off and install the new bushing. Replace the panel. Put the food contents back inside the freezer and refrigerator and restore the power.This motor mounting bushing is an authentic OEM replacement part sourced directly from the manufacturer. It is sold individually. It is designed for use in refrigerators manufactured by Frigidaire, Kenmore, Gibson, and Kelvinator.

Fix a loose or vibrating trimmer motor with this front motor mounting bracket. Secures the motor assembly to the housing. Easy 15-minute repair.

Fix squealing freezer noise or warm fridge temps? Your evaporator fan motor may have failed. Most DIYers replace this in 10-15 minutes with basic tools.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Upper door hinge for refrigerators. Mounts at the top of the door to support and secure it to the cabinet. Replace if cracked, bent, or worn out.

Replacement washer for refrigerator assembly. Ensures proper spacing and secure mounting. Order a new washer if yours is missing, damaged, or worn.

Tapping plate that mounts to the freezer cabinet structure. Replace this metal plate if it's cracked, bent, corroded, or missing to restore proper assembly.

Refrigerator bottom hinge shim that provides proper spacing and alignment for your door hinge. Replace if worn, damaged, or missing to restore fit.

Lower door hinge for refrigerators. Mounts at the bottom of the door to support weight and allow opening. Replace if cracked, bent, or worn out.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Illuminates your oven interior so you can monitor cooking without opening the door. Replace when burned out or dimming. Verify fit with your model number.

Refrigerator not cooling but freezer icing up? The defrost timer controls the defrost cycle. Most DIYers replace it in 5-15 minutes with our video guide.

Routes defrost water from the freezer to the drain pan. Replace if cracked, clogged, or disconnected to prevent leaks and water pooling inside your unit.

Temperature control knob for refrigerators. Mounts on the control panel to adjust cooling settings. Replace if cracked, broken, or missing.

This part has been discontinued by the manufacturer and is no longer available.

Replace your refrigerator's mounting nut if it's stripped, missing, or damaged. This hardware component secures parts and panels in place during assembly.

Sold individually.

Interior light won't turn on or stays on when door closes? This door-activated switch controls your refrigerator light circuit. DIY repair in 15 minutes.

Fixing frost buildup between refrigerator and freezer compartments? This mullion heater prevents ice formation in the center divider. DIY-friendly repair.

The Freezer Shelf is an OEM part for Frigidaire freezers. This shelf provides additional storage space within the freezer, allowing for organized placement of frozen foods and optimizing the use of available space.

Common causes of a bad freezer shelf include overloading the shelf with heavy items, accidental impacts that can cause bending or breakage, or regular wear and tear from frequent use. 

Symptoms of a bad freezer shelf include:

• Cracks or breakage in the shelf material
• The shelf not fitting securely or wobbling
• Difficulty in sliding or positioning the shelf
• Visible warping or bending

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement control knob for your refrigerator. Installs on the temperature control panel. Needed when original knob is cracked, broken, or missing.

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

This screw fastener secures appliance panels and small components to restore proper fit and reduce vibration. It's a direct-replacement OEM-style fastener used where factory screws are required. What it does:

• Secures trim, panels, or brackets to prevent rattling and misalignment
• Replaces missing or damaged screws that allow parts to shift or vibrate
• Restores stable mounting for controls, housings, and interior components
• Helps maintain proper gaps and seals when fastening exterior or interior pieces

• One screw fastener

• Unplug the appliance or disconnect power before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Install by hand initially, then snug—do not overtighten to avoid damaging threads or parts
• If original screw is corroded or broken, compare head type and length to ensure correct fit