Parts for Amana TRI18TL / P1303202W L: 02 - Door Assemblies Parts

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This screw secures appliance panels and components to keep assemblies stable and aligned during normal use. It's a direct-fit fastener used where the factory requires a specific screw shape and thread. What it does:

• Fastens trim, panels, brackets, or internal components to the cabinet or frame
• Restores secure mounting when original fasteners are missing or stripped
• Helps eliminate rattling, vibration, or loose parts caused by a missing screw
• Matches OEM fit and fastening points for correct assembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Replace only the damaged or missing screw; confirm orientation and thread engagement before final tightening
• Disconnect power and follow all safety precautions before servicing appliances

This screw secures appliance panels and components to keep assemblies stable and aligned during normal use. It's a direct-fit fastener used where the factory requires a specific screw shape and thread. What it does:

• Fastens trim, panels, brackets, or internal components to the cabinet or frame
• Restores secure mounting when original fasteners are missing or stripped
• Helps eliminate rattling, vibration, or loose parts caused by a missing screw
• Matches OEM fit and fastening points for correct assembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Replace only the damaged or missing screw; confirm orientation and thread engagement before final tightening
• Disconnect power and follow all safety precautions before servicing appliances

This freezer door gasket creates the seal between the freezer door and cabinet to help retain cold air and reduce frost buildup. Replacing a worn or damaged gasket restores a proper seal and helps maintain consistent freezer performance. What it does:

• Forms an airtight seal around the freezer door to help keep cold air in and reduce ice buildup.
• Addresses common symptoms such as visible gaps or cracks in the seal, excessive frost/ice, or a door that doesn't close flush.
• Matches the OEM sealing profile to restore correct fit and function.
• Helps the freezer maintain stable temperatures when the door seal is intact.

• Disconnect power and remove food/ice from the freezer before beginning work.
• Clean the gasket channel/mating surface and remove the old gasket completely before installing the new one.
• Installation methods vary by model (press-in, retainer clips, or adhesive); for exact instructions.
• After installation, inspect door alignment and test closing to ensure a uniform seal.

This refrigerator door gasket seals the fresh food door to keep cold air in and moisture out. Replace a worn seal to restore temperature control, reduce condensation, and help the appliance run efficiently.

• Creates an airtight seal between the door and cabinet
• Helps maintain stable interior temperatures and reduce energy loss
• Limits moisture buildup around the door opening
• Replaces gaskets that are cracked, torn, shrunken, deformed, or not sealing

• Disconnect power before servicing
• Allow the new gasket to relax; if needed, warm it in hot water to ease installation
• Remove the old gasket carefully; seat the new gasket fully into the door channel, checking corners
• Verify door alignment and test the seal by closing on a sheet of paper and adjusting as needed

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This part has been discontinued and is no longer available.

This part has been discontinued and is no longer available.

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping