Need Help?
Call or text
Show parts
The carburetor gasket plate creates a seal between the air cleaner base and the carburetor body. This plate is made of durable material but it is exposed to constant pressure and heat, which can cause it to degrade over time. It can also become damaged or broken, which would require a replacement. If the gasket is degraded or damaged, it could allow air to leak out of the engine, reducing compression and affecting performance. Severe cases could result in total engine failure, which is why replacement should be done as soon as possible. This genuine OEM gasket plate is designed to be used in a variety of log splitters, tillers, and lawn mowers from brands like Yard Machines, MTD, Yard Man, Cub Cadet, Troy-Bilt, and Husky. This carburetor gasket plate is made of durable materials and sold as an individual piece. No hardware is included for this part and will require an additional purchase if needed. Always allow the engine to cool before performing repairs and wear gloves for hand protection.
Usually ships within 4 - 14 days
A gas powered engine often requires priming before it can run, which means injecting some of the fuel into the engine's carburetor. Here, a careful balance of air and gas will receive a spark that causes combustion. The most common way to prime an engine is to use a primer assembly that is activated by a bulb that is pressed to create suction and draw fuel into a reservoir or carburetor. This replacement fuel bulb is for snowblowers that rely on gas powered engines to run. The fuel bulb is very flexible and made to endure seasonal conditions. It works with Craftsman, Yard Machines, MTD, Troy Bilt, and Bolens snowblowers. This is an OEM replacement part that fits into the cover assembly and which requires only a wrench to replace and install. It is sold individually, and other components of the priming assembly may be needed.
The primer bulb is a small plastic piece that will draw fuel from the fuel reservoir and into the carburetor when it is pressed down. This ensures that the fuel can get into the carburetor so that combustion can happen in the engine. If the primer bulb is broken or damaged on the engine, it will mean that the carburetor will not be getting the fuel it needs to get the engine to start. In some cases, the engine might not start at all. Other times, it might take a while to get the engine to start. These could indicate that it is time to replace the bulb. This is an OEM replacement part that is sold individually. It will work with lawnmowers and other types of small engines. The bulb is compatible with a range of different popular brands including Toro, Kawasaki, Cub Cadet, MTD, and Craftsman.
It's best to have spare O-ring gaskets on hand to rebuild a carburetor when the need arises. Use this manufacturer-approved replacement part to complete the process. When outdoor power equipment shuts off just after starting or won't start altogether, there may be a problem with the carburetor. It could be a leak that causes compression problems keeping the machine's engine from starting. Gasoline may drip from the float bowl because of an O-ring that won't seal or seat evenly all around, or one that has become brittle over time. This is a genuine OEM part compatible with specific lawnmowers, snowblowers, wood chippers, log splitters, tillers, and other garden maintenance machines from Craftsman, MTD, Cub Cadet, MasterCut, Troy-Bilt, and Yard Machines. It is sold individually.
The fuel bowl gasket provide an airtight seal to the fuel bowl. This will ensure that air, along with dirt and debris, do not make their way into the fuel. Gaskets will wear out over time. They will start to crack and fall apart, and they will no longer be capable of providing you with the necessary seal for the fuel bowl. The repair is easy and should only take between half an hour and an hour. This is an OEM replacement fuel bowl gasket part that is made from high-quality, durable rubber. Each of the fuel bowl gaskets is sold individually. The gasket can work well with many different types of outdoor power equipment, including snowblowers, chipper-shredders, tillers, lawn tractors, mowers, and other small engines. The fuel bowl gasket is compatible with many brands, including MTD, Yard Machines, Yard-Man, Troy-Bilt, Huskee, Cub Cadet, and Mastercut.
This is a genuine OEM replacement fuel bowl bolt for a snowblower, tiller, or chipper engine. The fuel bowl is a part of the fuel filtration system designed to prevent sediment from clogging up the carburetor. Fuel moves from the fuel tank and passes through the fuel bowl to catch any debris. It is essentially a particle filter. This bolt mounts the fuel bowl in place. The two most likely reasons why a fuel bowl bolt might need replacing are general wear and tear or loss. This bolt is located fairly close to the outside of the engine, making it more susceptible to the elements. Over time, the bolt may corrode and will need replacing. If lost while making a repair to the fuel bowl itself, the fuel bowl bolt will need to be replaced. Use a wrench to make the repair. This fuel bowl bolt is a top of the line replacement part for Bolens, Yard Machines, MTD, Troy-Bilt, Huskee, and Yard Man appliances. This part does not include any additional hardware, as it ships individually.
The fuel drain plug gasket creates a solid, leak-proof seal in the fuel drain. The gasket goes into the connection between the drain and the fuel tank. In the event that this gasket fails, there could be fuel leakage from the equipment that could be costly or even dangerous. Make sure to inspect and replace all gaskets regularly to ensure that the engine is working efficiently. This gasket is made of durable rubber material and is simple to install. drain the fuel to provide access to the drain plug and the fuel line without spilling fuel everywhere. Always wear gloves and make sure to disconnect the spark plug or disable the engine before working on any outdoor power equipment. This OEM replacement fuel drain plug is compatible with several tillers, snowblowers, lawnmowers, tractors, and other outdoor power equipment made by Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Huskee, Yard-Man, and MasterCut. Sold individually.
This carburetor insulator is a genuine MTD replacement part for appliances with small engines, such as lawn mowers, lawn tractors, lawn trimmers, snowblowers, chipper shredders, tillers, and leaf blowers. The purpose of a carburetor insulator is to keep the heat of the running engine away from the carburetor, which combines the air and fuel that ignites the engine. This keeps the engine from overheating and suffering damage as a result.While there is a chance that a damaged carburetor insulator could prevent the engine from igniting altogether, it is more likely that a damaged carburetor insulator will allow for unmetered air leaks into the carburetor. Unmetered air leaks will cause the engine to take in more fuel, reducing the fuel economy of a small engine appliance. For this reason, if the symptoms align with a diagnosis of a damaged carburetor insulator, it must be individually replaced as soon as possible before using the small engine lawn appliance again.This carburetor insulator is compatible with the following brands: MTD, Cub Cadet, Yard Machines, and Craftsman.
This is a genuine carburetor insulator gasket that is designed to fit select models of lawn mowers. The carburetor insulator gasket is responsible for insulating the carburetor to create a strong seal between it and the engine block and insulate it from the excess heat. This gasket is subject to constant pressure and extreme heat, which can cause it to compress, warp, or become otherwise damaged as a result of regular use. Gaskets should be on the routine maintenance schedule and should be inspected every time other repairs are performed. Without functional gaskets, the engine may run poorly or may not run at all. This genuine OEM carburetor gasket is manufactured by MTD. It can be used in select machines from this brand, as well as those from Troy-Bilt, Cub Cadet, HUSKEE, Yard Man, and Yard Machines. There are hundreds of compatible units that take this gasket. The gasket is made of durable composite materials and sold as an individual unit. Hardware and additional components will require another purchase. Be sure to allow the engine to cool and use the appropriate tools for proper installation without damaging the gasket. Always drain the fuel system before working on the carburetor or internal engine components.
This is a carburetor stud for a lawn mower or tiller engine. A carburetor stud enables the carburetor to stay sealed to the intake manifold. They prevent threads from stripping in the metal manifolds and keep the carburetor perfectly aligned. This is an OEM part sourced directly from the manufacturer and is sold individually. When cleaning a carburetor, the user will need to remove the studs. Do not use vice grips when removing a stud, as this will strip the threads. A trick is to put two nuts on the threads and then hold a wrench behind the back nut. Tighten the closest nut, and then use another wrench or impact gun to reverse the stud out. This also works in reverse for replacing it with a new stud to properly place the carburetor so that it seals to the manifold.This part is compatible with several brands, including Bolens, Cub Cadet, Husky, Troy-Bilt, Yard Machines, and Yard Man.