Parts for Lg LMHM2237ST: Base Plate Parts

Size: 5 inches x 7 3/4 inches.

The Decor Front is an OEM replacement part for LG microwaves. This component serves as the outer trim or decorative front piece of the microwave, enhancing its appearance and ensuring a clean, finished look. It also helps to protect internal components from dust and debris.

Causes of a bad decor front can include physical impact, heat damage from frequent use, or wear and tear over time.

Symptoms of a bad Decor Front include:

• Cracks or breaks in the trim
• The trim becoming loose or detaching from the microwave
• Discoloration or warping due to heat exposure
• Difficulty in maintaining a clean, polished appearance

This OEM LG part is also compatible with Sears/Kenmore models.

This is a replacement plastic filter cover that secures and protects the appliance filter, helping maintain proper airflow and filter positioning for reliable operation. Fits into the filter housing to keep the filter sealed and supported. What it does:

• Holds the appliance filter in place to prevent shifting during operation
• Protects the filter from accidental damage and large debris
• Helps maintain proper airflow and filtration performance when installed correctly
• Commonly replaced when cracked, warped, missing, or no longer latching securely

• Disconnect power to the appliance before servicing to avoid electrical or mechanical hazards
• Remove the old cover by releasing any tabs or screws, then align new cover tabs into the housing and snap or fasten into place
• Do not force the cover; ensure proper alignment to avoid damaging mounting tabs
• If clips or screws are damaged, replace them before operating the appliance

This supporter holder is a replacement mounting bracket that secures internal components and helps maintain proper alignment for stable operation. Install the bracket to replace a cracked, broken, or missing holder and reduce movement or noise. What it does:

• Secures and supports internal assemblies or panels to keep parts aligned.
• Replaces cracked, broken, or missing holders that allow components to shift.
• Designed to match OEM mounting locations for a direct-fit replacement when used with the correct part number.

• Disconnect power (and water supply if applicable) before beginning any repair.
• Use basic hand tools; save original fasteners or replace damaged hardware with identical fasteners.
• Inspect adjacent parts and mounting points for damage and replace if necessary for a secure fit.

This choke cover is the inner perimeter trim that snaps onto the microwave door. It secures the door choke and helps maintain proper door shielding and appearance. Replace a cracked or missing cover to restore a secure fit.

• Secures the door choke around the inner door frame
• Helps maintain proper door shielding and consistent door alignment
• Covers and protects door-frame edges for a finished look
• Helps with: cracked/missing inner trim, loose or rattling cover, visible gaps at the door perimeter, or arcing at the door edge

• Disconnect power or switch off the circuit breaker before servicing; support over-the-range units as needed
• Work on a padded surface; carefully release perimeter tabs/clips and avoid prying against the glass
• Ensure the door choke/gasket is seated evenly, then align and snap the new cover fully around the perimeter; verify smooth, even door closure
• Microwaves contain high-voltage components.

The Locker is an OEM part for LG microwaves. This part secures the microwave's hood in the desired position, whether it's slid out for venting or retracted for a sleek appearance.

Causes of a bad part can include mechanical wear from repeated use, physical damage or impact, or issues with the internal mechanisms that control the locking mechanism.

Symptoms of a bad Locker include:

• Difficulty in sliding the microwave hood in or out
• The hood failing to lock securely in position
• Excessive movement or rattling of the hood when locked

This OEM LG part is also compatible with some Kenmore models.

This glass turntable plate fits microwave ovens to provide a stable, rotating surface for cookware and food, helping heat items more evenly and preventing spills during operation. What it does:

• Supports dishes and containers while the microwave's turntable motor rotates them
• Promotes more even heating by allowing food to rotate during cooking
• Replaces cracked, chipped, or missing microwave glass plates
• Restores safe, stable operation when the original plate no longer seats properly

• Handle carefully; glass may be heavy or break if dropped
• Place the plate onto the microwave's roller guide/turntable support so it seats securely
• Clean with mild detergent and avoid abrasive cleaners to preserve the finish
• Do not operate the microwave without the turntable and support properly installed