Parts for Ge PGS960BEL1TS: Body Parts

This replacement screw secures appliance components and helps keep panels, brackets, and controls firmly attached for reliable operation. It's a simple, direct fix when a mounting screw is missing, loose, or stripped. What it does:

• Fastens panels, trim, brackets or electrical components to reduce movement and rattling.
• Restores proper alignment of parts that shift when a screw is missing or worn.
• Helps maintain electrical and mechanical connections by keeping components seated.
• Common symptom: loose or vibrating panels, trim gaps, or visibly missing hardware.

• Disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Thread gently and avoid overtightening to prevent stripping the mating threads or cracking surrounding parts.
• Keep any removed hardware organized to ensure placement of all required fasteners during reassembly.

The Machine Board with Frame is an OEM component specifically designed for GE gas ranges. This board oversees critical cooking functions including ignition, temperature control of the burners and oven operations. 

Symptoms of a bad machine board include:

• Burners not lighting properly or staying lit
• Oven not reaching or maintaining set temperatures 
• Improper burner or oven shut-off
• Control buttons and display malfunctions

Causes of a bad machine board can be failures over time due to heat stresses, appliance age, electrical surges, or physical impacts.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The GE spark module kit is an OEM replacement part for GE stoves and ranges. It generates the spark needed to ignite the gas burners. The kit includes the spark module and associated wiring harness. When the burner control knob is turned to the "ignite" position, the spark module receives a signal and activates. It then produces an electrical spark that ignites the gas as it flows from the burner orifice, allowing the burner to light.

Over time, spark modules can fail due to electrical issues, wear and tear from frequent use, or exposure to moisture. A malfunctioning spark module can disrupt the ignition process, making it difficult to light the burners.

Symptoms of a bad spark module include:

• Burners not igniting
• No clicking sound when turning the burner knob
• Intermittent sparking
• Only some burners igniting

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is the flat wire shelf that slides into your oven's side supports to hold bakeware at the right height. Replace a bent or missing rack to restore safe, stable, and adjustable cooking space.

• Provides a sturdy, level surface for pans and dishes at multiple rack positions
• Slides in and out for easy loading and checking of food
• Helps position food correctly for even baking, roasting, or broiling
• Common symptoms: rack is warped, wobbly, missing, or difficult to slide

• Allow the oven to cool completely; wear gloves to protect hands.
• Pull the old rack to the stop, tilt the front up to clear the stop, and remove.
• Align the new rack with both side rails; insert the rear first, lower the front, and slide fully in.
• Refer to your owner's manual for recommended rack positions and any self-cleaning guidance.

The Line Cord is an OEM part for GE gas ranges. It safely delivers gas and electrical supply between the range and household connections.

Causes of failure can be insulation cracks from repetitive plug insertion/removal, bent pins compromising contacts, or wire fatigue over prolonged usage.

Symptoms of a faulty line cord include:

• Gas valves failing to activate or ignite burners 
• Lights/igniters not illuminating due to interrupted power
• Potential shock or fire hazard from exposed wire ends

This OEM part is also compatible with Hotpoint and RCA gas range models.

This anti-tip bracket secures the rear of your range to the floor or wall so the rear leveling leg locks in place. Replacing a missing or damaged bracket helps prevent tipping and keeps the appliance stable during everyday use.

• Anchors the range to a fixed point; rear leveling leg engages the bracket
• Helps prevent forward tipping when weight is placed on an open oven door
• Reduces rocking or sliding during cooking or cleaning
• Replace if the bracket is missing, bent, corroded, or the unit fails the anti-tip check

• Disconnect power and, if applicable, shut off gas before servicing
• Pull the range straight out; position the bracket per your installation manual/template
• Fasten the bracket securely to floor or wall studs using hardware appropriate for your surface
• Slide the range back so the rear leg fully engages the bracket; perform the anti-tip test from your manual

This spacer base positions and supports components inside the appliance to maintain correct alignment and clearance, helping reduce vibration and wear. It's a simple replacement part when the original is cracked, broken, or missing. What it does:

• Provides a stable mounting surface and correct spacing for internal panels or components
• Restores proper alignment to reduce vibration, noise, and uneven operation
• Commonly replaced when the original spacer is cracked, deformed, or missing
• Helps maintain secure fastener engagement and proper component clearance

• Spacer base (single piece)

• Disconnect power to the appliance before starting any repair
• Follow manufacturer service instructions or parts diagram for correct location and orientation
• Basic hand tools typically required; inspect surrounding fasteners and mounting surfaces during installation

This support base secures and stabilizes the appliance cabinet/frame so doors and components align properly and operate smoothly. Replaces worn or broken right-side lower support to restore correct support and fit. What it does:

• Provides structural support for the appliance cabinet/frame on the right side
• Helps maintain proper door alignment and prevent sagging or uneven gaps
• Reduces vibration and rattling related to a compromised support
• Restores correct mounting for adjacent components or trim

• Disconnect power and empty doors/drawers before starting any repair
• Remove relevant trim or access panels to reach the support; keep fasteners for reuse
• Replace using the original mounting locations; do not force or bend surrounding panels

This support base replaces the left lower support used to stabilize and align the appliance's lower assembly, restoring proper fit and reducing vibration. It helps keep moving parts supported during normal operation. What it does

• Provides structural support for the appliance's lower assembly and related components.
• Restores proper alignment to reduce rubbing, vibration, or uneven movement.
• Helps prevent excessive wear on brackets, panels, and adjacent parts.
• Safe, commonly used when the left support is cracked, broken, or warped.

• Disconnect power (and gas, if applicable) before beginning any repairs.
• Handle sharp sheet-metal edges and wear gloves and eye protection.
• Require basic hand tools to remove panels and fasteners; keep hardware for re-use if undamaged.
• If other mounting hardware or adjacent parts are damaged, inspect and replace as needed for secure installation.

This replacement lamp cover protects and diffuses interior appliance light for even illumination and safe bulb containment. It restores a cracked, cloudy, or missing light lens to improve visibility inside the compartment. What it does:

• Protects the interior light bulb from impact, moisture, and food debris.
• Diffuses and softens the bulb's light for more even interior illumination.
• Stops rattling or falling lens issues caused by a cracked or broken cover.
• Helps prevent direct contact with the hot bulb and reduces glare.

• One lamp cover / light diffuser.

• Disconnect power or unplug the appliance before servicing to avoid electrical shock.
• Remove the old cover carefully and dispose of any broken pieces safely.
• Handle the replacement cover gently to avoid cracks; align and snap/slide into place per the original mounting.
• After installation, restore power and replace bulb if still dim or nonfunctional.

The Probe Thermistor is an OEM replacement part for GE wall ovens and ranges. Located inside the oven cavity, this temperature-sensitive probe precisely monitors interior heat to safeguard against overcooking.

Causes of a faulty thermistor involve exposure to excessive cooking temperatures, moisture infiltration from spills or steam, or basic failure due to old age.

Symptoms of an inadequate probe thermistor include:

• Inaccurate temperature readings and baking inconsistencies
• Oven temperature exceeding desired setting risking fire

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Size: 10-32 GXTT FLP.595 S