Parts for Hot Point RAS240DM1WW: Body Parts

This left side complement is a refrigerator interior trim piece that restores proper support and alignment for door components and liners. Replaces damaged or cracked left-side trim to help the door seal and close correctly. What it does:

• Replaces a cracked, broken, or missing left side interior trim piece
• Helps secure door liners and internal components to the cabinet frame
• Restores proper alignment so the door closes and seals as intended
• Reduces rattle or movement caused by a loose or damaged trim

• One left side complement piece

• Disconnect power to the appliance before beginning any repair
• Remove the door liner/panels and retainers as needed to access the left side complement
• Use basic hand tools; handle trim carefully to avoid damaging adjacent liners or gaskets
• OEM instructions for correct removal and torque specifications

Replacement oven rack that slides inside your range to hold cookware and bakeware. Needed when original rack is bent, warped, missing, or damaged.

This tablet cover replaces a damaged or missing control-panel bezel to restore the look and basic protection of the appliance control area. It helps keep buttons and switches covered and prevents direct contact with wiring and components. What it does:

• Covers and protects the control panel area from spills, dirt, and everyday wear
• Restores cosmetic appearance when the original cover is cracked, warped, or broken
• Keeps the control buttons and display area secured and aligned
• Prevents accidental contact with internal components behind the console

• One tablet cover

• Disconnect power to the appliance before starting any work
• Removal typically requires removing the console or trim screws and lifting the old cover off its mounting tabs
• Handle plastic tabs gently to avoid breakage; reuse existing fasteners if in good condition

Replacement 8-18 x 5/16 screw secures range panels, brackets, and components. Needed when original fastener is stripped, missing, or damaged.

White side panel assembly for electric and gas ranges. Covers and protects the exterior side of your range. Replace if cracked, chipped, or discolored.

Replace your cracked or stained oven bottom panel. This flat inner surface supports cookware, protects components from spills, and restores a clean base.

This housing receptacle is the molded mounting and connection point that secures and protects the oven/range control wiring and plug-in module, helping maintain reliable electrical contact and safe operation of the control components. What it does:

• Provides a secure housing for the control module or wiring receptacle to prevent movement and wear
• Protects electrical connections from abrasion and incidental contact
• Keeps the control harness aligned for consistent plug-in engagement
• Can resolve issues like intermittent control operation or loose control module connections

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Basic hand tools are typically required; note wire harnesses and screw locations before removal.
• Handle plastic tabs and mounting points gently to avoid breakage; replace any damaged fasteners.

Anti-tip bracket assembly secures your range to the wall or floor, preventing dangerous tipping. Replace if bracket is bent, broken, or missing.

Replacement cover support base that secures the range top and stabilizes the control area. Needed when original is cracked, broken, or missing.

This cover support base secures the appliance control/console cover, restoring proper support and alignment so the cover stays in place during use and service. Fits the original mounting location to prevent sagging or vibration. What it does:

• Supports the control or console cover at its mounting point to keep the cover stable
• Restores proper cover alignment to reduce rubbing, rattling, and gap-related noise
• Allows safe access to internal components by holding the cover correctly during service
• Replaces cracked, worn, or broken support pieces that cause loose or unstable covers

• Disconnect power before beginning any service to avoid shock or injury
• Basic hand tools are typically required to remove the cover and replace the support
• Handle the control/console cover carefully to avoid scratching or damaging adjacent parts
• Verify alignment and secure mounting after installation; do not overtighten fasteners

Machine screw that secures panels, trim pieces, and brackets on ranges. Replace stripped, damaged, or missing screws to keep components properly fastened.

This spacer base provides a durable mounting spacer used to properly position and support appliance components, helping maintain correct alignment and fit for reliable operation and safe use. What it does:

• Positions and spaces panels or assemblies to ensure proper alignment
• Supports components to reduce stress and vibration during operation
• Helps maintain correct clearances for seals, doors, or trim pieces
• Can prevent rubbing or binding caused by a missing or damaged spacer

• Inspect surrounding parts and mounting points for wear before replacing the spacer
• Use correct screws/fasteners and tighten to OEM torque specifications where provided
• Disconnect power to the appliance before performing any work that exposes wiring or electrical components

Clear glass lens that protects your oven light bulb. Replace if cracked, broken, or cloudy to safely view cooking progress. Confirm fit with model number.

Secures range door handles and attaches components. Replace when cracked, bent, or missing to restore stable grip. Confirm fit with your model number.

Oven not heating or baking unevenly? This lower bake element restores proper oven temperature for even cooking. Moderate DIY repair with basic tools.

If your oven won't broil or browns unevenly, the broil element has likely burned out. This heating element restores intense top heat for proper searing.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Seals your range door to maintain consistent oven temperature and improve cooking efficiency. Replace if torn, worn, or heat-damaged. Confirm fit with your model.

Mounting screw for refrigerator doors, shelves, kickplates, and interior components. Replace missing, stripped, or corroded screws during repairs.

Replace a cracked or broken door receiver hinge on your electric or gas range. This structural part secures the door panel and ensures proper alignment.

Left-hand gusset hinge bracket for range oven doors. Replaces broken, cracked, or worn hinge support brackets that cause misalignment or door issues.

Right-hand hinge gusset for range oven doors. Replaces cracked, bent, or broken mounting bracket. Ensures proper door alignment and support.