Need Help?
Call or text
Mounts the water filter base to the refrigerator cabinet. Replace this bracket if cracked, broken, or missing to keep the filter housing secure and aligned.
Video after video on how to replace cover, none to show how to replace entire compartment, had to figure it out myself. Read more
This accessory assembly is the factory-specified kit used to attach or secure designated parts on your appliance. Replacing missing or worn pieces restores a solid, factory fit and finish.
Because of the design of the plates holding my LG dryer on it's pedestal (screws on the pedestal and two face tape on the dryer end of the plates), I needed to order a set of replacement plates. The installation was straight forward for the most part. First I would bend back a small corner of the protective cover on the two face tape to make it easy to remove. Then I would attach the plate to the pedestal using the required 2 screws started in the associated holes, only starting the... Read more
Secures the detergent dispenser to the dishwasher inner door panel. Replace if cracked, broken, or rusted to restore proper alignment and mounting.
New brackets. Read more
Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
This latch body is the door latch component that secures the appliance door during operation, restoring reliable closure so cycles can run normally. Use it to replace a worn or damaged latch that won't hold the door closed. What it does:
Replaced all three door switches and bracket. It had a break in it. Took less than an hour to fix once all parts arrived. Read more
Pivot block kit that supports refrigerator door alignment and smooth movement. Replace if broken, cracked, or worn to prevent door sagging and rubbing.
Replaced broken pivot block. Read more
Secures the clock/timer or electronic oven control behind your range's control panel. Replace if bracket is bent, broken, or missing to keep display aligned.
I took off the back cover of the range. I then took out the bolts which had held the control board in. I placed the control overlay on the new control board, and then plugged it in. I bolted the control board in place and replaced the back cover. For $135 in parts and 15 minutes of labor, I did what the appliance repair company wanted to charge me $500 for. Read more
Drawer wedge guide aligns and stabilizes your range's lower drawer for smooth operation. Replace if cracked, broken, worn, or missing to eliminate wobble.
Metal contact leaf for dishwasher switch assemblies. Replace if the original contact is bent, corroded, worn, or missing to restore proper circuit closure.
Supports and aligns the refrigerator door at the bottom pivot point. Replace if bent, cracked, or worn to restore proper door alignment and movement.
I replaced all parts on the bottom of the door to make it smooth to open. It was easy and took about 15 mins total. Read more
Replaces cracked or broken mounting bracket in your freezer. Securely holds internal components in proper alignment. Needed when original is damaged.
Secures your cooktop to the countertop from below. Includes brackets and hardware. Replace if worn, deformed, or screws are damaged or missing.
Bought parts needed. Quick turn around from y'all. All is good cause mama's happy. Read more
Secures components to your microwave frame for proper positioning. Replace this bracket if bent, broken, or missing to restore stability and support.
The replacement part fit perfectly. Read more
Secures the ice maker assembly inside your refrigerator for stable positioning and proper alignment with the water fill tube. Replace if cracked or broken.
Installed new Ice maker. Arrived within a few days and installed easily. Read more
Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.
Replaced spider arm, bearings, drum seal. AppliancePartsPros had the overall cheapest price and factory parts not knockoffs. Had all my important parts <2 days and the rest on the third day. Good on line tutorial ideas. Good company. Will do business again. Read more
This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.
Installed new screws. Read more