Parts for Kenmore 911.7398812 (9117398812, 911 7398812): Broiler And Oven Burner Section Parts

This is a package of twelve replacement nuts used to secure appliance panels and components. These genuine-style nuts restore fastener retention to reduce looseness and rattling and help keep parts aligned during operation. What it does:

• Secures panels, brackets, and fasteners to maintain proper component alignment
• Prevents vibration-related loosening that can cause noise or intermittent contact
• Replaces missing or damaged nuts that can allow parts to shift or fall off
• Used wherever the matching nut size and thread are required by the appliance

• Disconnect power (and gas, if applicable) before servicing the appliance.
• Verify the nut size and thread match the stud or bolt before installation.
• Hand-start threads, then tighten with the appropriate driver or wrench; avoid overtightening.

The Round Style Oven or Broiler Igniter is an OEM replacement part for GE gas ranges and cooktops. It has a round design and is responsible for reliably igniting the gas burners with each use.  Range: 2.5 to 3.0 amps. 

Causes of a bad igniter can include wear and tear from repeated heating and cooling cycles, damage or defects in the electrical components, or issues arising from long-term exposure to high heat.

Symptoms of a bad igniter include: 

• Difficulty starting or unreliable ignition of gas burners  
• Burners failing to ignite with the press of the control knob
• Intermittent ignition problems
• Clicking sounds but no ignition

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This replacement screw secures appliance components so panels, brackets, and assemblies stay tight and aligned. Replace stripped or missing hardware to eliminate rattles and keep your unit assembled safely and correctly.

• Fastens panels, brackets, or components to the appliance frame
• Restores a secure fit when the original screw is lost, stripped, or corroded
• Helps prevent vibration noise and movement during operation
• Supports proper alignment of trim and assemblies

• Disconnect power; for gas units, also shut off the gas supply
• Use the correct driver to avoid stripping the head; do not overtighten
• Inspect and address damaged mating threads, clips, or brackets before reinstalling
• Refer to your model's parts diagram to confirm location and quantity

ST10-16 X 7/16"

The Suspension Spring is an OEM replacement part for Whirlpool washing machines. It is a critical component that helps to support and stabilize the outer tub during the wash and spin cycles, absorbing vibrations and minimizing excessive movement.  

Symptoms of a bad suspension spring include:

• Excessive shaking or vibrating during the wash or spin cycle
• Loud banging or rattling noises from the washer
• The washer moving or "walking" across the floor during operation
• Leaks or potential damage to other components due to increased stress and movement

Causes of suspension spring failure can range from general wear and tear over time and exposure to high-speed spinning, to physical damage from overloading or unbalanced loads.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Nickel

Nickel

This replacement screw secures appliance components so panels, brackets, and assemblies stay tight and aligned. Replace stripped or missing hardware to eliminate rattles and keep your unit assembled safely and correctly.

• Fastens panels, brackets, or components to the appliance frame
• Restores a secure fit when the original screw is lost, stripped, or corroded
• Helps prevent vibration noise and movement during operation
• Supports proper alignment of trim and assemblies

• Disconnect power; for gas units, also shut off the gas supply
• Use the correct driver to avoid stripping the head; do not overtighten
• Inspect and address damaged mating threads, clips, or brackets before reinstalling
• Refer to your model's parts diagram to confirm location and quantity

This heat-resistant fiberglass oven door gasket seals the oven cavity perimeter, helping keep heat inside for consistent temperatures and efficient cooking. Replace a worn, frayed, or flattened seal to restore proper door sealing performance. What it does

• Forms a heat-resistant seal around the oven opening to minimize heat loss
• Helps maintain set temperature and overall cooking performance
• Can help address long preheat times, uneven baking, and hot air leaking around the door
• Replace if the gasket is frayed, brittle, compressed, or falling out of its channel

• Includes: 1 fiberglass door gasket

• Disconnect power and allow the oven to cool completely before service
• Remove the old gasket from its mounting slots or clips; clean the channel of debris
• Install the new gasket without stretching; seat it evenly around the perimeter with ends routed as originally positioned
• Close the door and check for uniform contact all around; adjust seating if needed

This broiler burner baffle directs heat and flames across the broiler chamber to promote even cooking and help protect the burner from drips and debris. It's a simple, durable sheet metal part used in gas broilers. What it does:

• Redirects and evens heat distribution under the broil pan for more uniform browning
• Shields the burner from food drips and grease to reduce flare-ups and clogging
• Helps maintain proper burner flame pattern for consistent broiling
• Can resolve uneven broiling, excessive flare-ups, or burner flame irregularities when worn or damaged

• Disconnect power to the appliance and shut off gas supply before servicing
• Allow the range to cool completely; use gloves to avoid sharp edges
• Remove broiler pan and any obstructions, then position the baffle so it seats over the burner supports as shown in your service literature