Parts for Lg LRMWS2906S/00: Case Parts

The Handle Mounting Stud is an OEM replacement part for LG refrigerator doors. It provides a sturdy mounting point for the door handle assembly. Reliable handle connection and support is crucial for dependable door function and access. 

Causes of a faulty stud can include damage from excess weight or impact over time rendering the stud loose or unstable.

Symptoms of a bad stud include:

• Loose or sagging door handle  
• Difficulty opening and closing the refrigerator door  
• Potential for the handle to detach completely
• Safety concerns if the handle connection fails

This OEM LG replacement stud is also compatible with Sears/Kenmore models. 

The Drain Pipe Assembly is an OEM replacement part for LG refrigerators. It is a plastic tubing system that collects and removes liquid condensation from evaporator coils. Proper drainage is crucial to minimizing frost buildup and ensuring optimal cooling of food storage areas. 

Symptoms of a bad drain pipe assembly include:

• Excessive frost or ice accumulation inside the refrigerator
• Puddling or leaks detected near evaporator housing
• Slow draining allowing water to pool versus emptying fully
• Cracks or breaks in the tubing prevent complete fluid removal

Causes are typically mineral sediment clogging drainage paths or deteriorating plastic from constant use. This OEM LG replacement pipe restores reliable condensate removal to maintain peak efficiency.

This OEM LG part is also compatible with Sears/Kenmore. 

The Leveling Leg is an OEM part for LG refrigerators. It is one of the four legs at the bottom corners that elevate and provide stability to the entire appliance.

Causes of failure can be broken mounting points that no longer provide secure elevation, full compression of the built-in cushioning, or damage from impact on an unlevel floor.

Symptoms of a faulty leveling leg include:

• Excessive shaking or vibrating of the refrigerator
• Door alignment issues where doors are difficult to open or close fully
• Visible leaning or misalignment of the refrigerator cabinet

This OEM LG part is also compatible with some Kenmore models.

The Link is an OEM part for LG refrigerators. It serves as an integral connector between the refrigerator door and cabinet, facilitating smooth opening and closing of the door. With durable construction and precise engineering, the link is designed to withstand the rigorous motion of hundreds of door openings without compromising functionality. 

Symptoms of a bad link include:

• Doors that do not close or seal properly 
• Excessive noise or vibration from the door area
• Damage, bending, or breakage of the connecting pieces
• Misalignment impairing proper door operation

Causes can stem from normal wear and tear over many years of use. Replacing a faulty link restores the refrigerator door's designed motion for convenient access to the interior.

This OEM LG part fits seamlessly while extending the product's useful life. This part is also compatible with Kenmore models featuring LG's refrigerator link assembly design.

The Cover Assembly is an OEM part for LG French door refrigerators equipped with integrated television screens. This cover protects the television when not in use.

Symptoms of a bad cover assembly include: 

• Cracked, clouded, or peeling finish reducing aesthetics
• Poor fit allowing dust entry near television components  
• Binding or getting stuck when opening and closing
• Hinges, pins, or latches weakened through repeated use

Causes of failure can be temperature cycling absorbing and releasing moisture daily, over-extension through careless opening/closing, or general wear from constant daily usage.

Replace yours today with this genuine OEM LG cover assembly to restore your refrigerator's integrated display features. A snug fit around the television combined with a durable surface protects against spills for reliable entertainment access. This replacement part is also compatible with KitchenAid, Samsung, and GE refrigerators featuring television modules.

Restore organized storage with this fresh room tray assembly for your refrigerator. It replaces a cracked or missing deli/fresh drawer so items slide smoothly and stay easy to see and reach.

• Creates the fresh room/deli drawer storage area in the refrigerator compartment
• Slides on the existing rails for smooth access to stored items
• Helps keep items contained and organized
• Replaces a cracked, warped, or missing drawer that won't slide or stay in place

• Remove the old drawer by pulling it out and lifting/tilting as your model's diagram shows; install by aligning with the rails and sliding in until fully seated
• Handle plastic carefully; do not force into place to avoid stress cracks
• No tools typically required; disconnect power only if working near electrical components

This tray cover replaces a damaged or missing appliance tray cover to restore a clean appearance and proper containment of spills. It fits into the existing tray location and helps keep interior surfaces protected during normal use. What it does:

• Covers the appliance tray to help contain spills, crumbs, and minor debris
• Maintains a finished look and helps prevent direct contact with the underlying tray
• Supports proper placement of removable trays or components that sit above it
• Useful when the original cover is cracked, warped, or otherwise compromised

• One replacement tray cover

• Basic snap-in or screw-in installation; confirm orientation before fastening
• Power off and unplug the appliance before attempting any service
• Use gentle pressure to avoid cracking the new cover; do not force damaged fasteners
• Replace missing or damaged screws or clips with OEM-specified hardware

The Deli Drawer Front Cover is an OEM part for LG refrigerators. It provides an attractive facia that protects the internal components of the deli drawer. This cover is designed to integrate with the style and finish of the refrigerator interior. 

Symptoms of a bad Deli Drawer Front Cover include: 

• Cracks, chips, or other visible cosmetic damage
• Discoloration that detracts from the aesthetics  
• The cover is loose, misaligned, or missing
• Difficulty opening or closing the deli drawer

Causes of a bad cover can be normal wear and tear over time from repeated use, as well as accidental drops or impacts that cause cracks or breaks.

This OEM replacement part is also compatible with select LG models.

Vegetable Tray Assembly keeps produce organized and supported inside the refrigerator's crisper area. Replace a damaged or warped tray to restore proper storage, prevent produce from sliding, and help maintain interior organization. What it does:

• Supports and contains fruits and vegetables in the refrigerator crisper area.
• Restores a stable surface when the original tray is cracked, chipped, or warped.
• Helps prevent items from sliding or catching while opening and closing the drawer.
• Intended as a direct replacement to return the crisper section to normal use.

• Remove produce and slide the crisper drawer out before replacing the tray.
• Inspect drawer guides and seating points for debris; seat the new tray fully into the guides.
• Handle carefully to avoid damage; wear gloves if surfaces are sharp or dirty.

This lamp cover is the replacement light lens that protects and diffuses the appliance's internal lamp, restoring even illumination and shielding the bulb from moisture and debris. It's a direct-fit exterior lens for the lamp assembly. What it does:

• Protects the interior lamp from dust, moisture and impact to help prevent bulb damage
• Diffuses and directs light for even illumination inside the compartment
• Restores a cracked, yellowed or missing lens to improve visibility
• Helps maintain the lamp assembly's proper fit and alignment

• One lamp cover / light lens

• Power off and unplug the appliance before beginning any service
• Remove lamp bulb per manufacturer instructions before replacing the cover to avoid damage
• Use proper tools and handle the lens gently to avoid scratching or cracking
• If mounting clips or screws are worn or missing, replace them separately

This rail guide assembly supports and guides a sliding drawer, bin, or rack along its track for smooth, stable movement. Replacing a worn guide restores easy operation and helps prevent sticking, wobbling, or the slide coming off the track.

• Guides and supports the sliding drawer/bin/rack on its rail
• Maintains alignment so it opens and closes smoothly
• Helps prevent binding, uneven extension, and derailment
• Typical symptoms: hard-to-open drawer, tilt or sag, squeaking/grinding, or visible cracks/warping in the guide

• Disconnect power to the appliance before servicing
• Empty and remove the drawer/bin; disengage from the tracks per your model's procedure
• Remove mounting hardware, transfer any brackets/clips from the old guide, and install the new guide in the same orientation
• Verify smooth travel and proper alignment before reloading

This freezer door foam assembly replaces the insulation layer inside a freezer door to help restore proper temperature control and reduce condensation. It fits into the inner door cavity to improve cold retention and door performance. What it does:

• Replaces deteriorated or waterlogged door insulation that can lead to warm spots
• Helps reduce frost or ice buildup inside the freezer by restoring proper insulation
• Limits condensation and moisture between door panels that can cause odors or corrosion
• Supports overall temperature stability for better freezer efficiency

• One freezer door foam assembly

• Disconnect power before servicing and work on a dry, level surface
• Remove the inner door panel to access the foam; keep fasteners and clips organized
• Insert foam carefully to avoid tearing; align with locating features in the door cavity
• If the door uses adhesive or retention clips, reuse original hardware or OEM-recommended replacements

This freezer door foam assembly replaces the insulating foam inside a freezer door to help restore the door's sealed fit and reduce air leakage. It helps improve temperature stability and reduces frost buildup when the existing foam is damaged. What it does:

• Replaces deteriorated or compressed insulation inside the freezer door
• Restores a tighter door seal to reduce warm air infiltration
• Helps reduce excessive frost or ice buildup caused by air leaks
• Supports consistent freezer temperatures and efficient operation

• Disconnect power before starting and work with the door supported or removed to avoid injury.
• Remove the inner door panel or liner carefully to access the foam; keep fasteners and clips organized.
• Fit the foam into the door cavity without overstretching; ensure even contact with mating surfaces for a proper seal.
• If adhesive, clips, or a door liner are required, replace or reinstall them as needed.

Replacement door gasket that seals the refrigerator door to help keep cold air in and warm air out, reducing frost and cold-air leaks and helping the appliance maintain consistent internal temperatures for food preservation. What it does:

• Creates an airtight seal around the refrigerator door to minimize cold-air loss
• Helps prevent frost buildup in the fresh-food compartment and freezer-adjacent areas
• Addresses symptoms like visible cracks, tears, gaps, or cold air escaping from the door edges
• Helps the fridge maintain set temperatures and can reduce the workload on the cooling system

• Disconnect power to the appliance before starting any repair
• Remove the old gasket fully and clean the door channel to ensure a proper new seal
• Press the new gasket into the channel evenly, working around the perimeter and checking for full contact
• After installation, close the door and inspect the seal; allow a short settling period and re-check for gaps

This door gasket seals the dishwasher door perimeter to keep water and steam inside the tub. Replacing a worn or flattened seal helps stop leaks and restores a consistent, reliable door closure. What it does:

• Forms a watertight seal between the door and tub during wash cycles
• Helps prevent leaks from the sides or bottom of the door
• Replace if the gasket is cracked, torn, deformed, or no longer springy
• Can help with symptoms like water on the floor at the front of the unit or difficulty latching the door

• Includes 1 door gasket

• Disconnect power and shut off the water supply before servicing
• Open the door, pull the old gasket straight out of the channel, and clean the groove
• Let the new gasket warm to relax kinks; start at the top center and press evenly into the channel down both sides—fully seat the corners and avoid stretching
• Close the door to help the seal set, then run a short cycle and check for leaks

This hinge cover assembly replaces a damaged or missing hinge trim to protect the hinge mechanism and restore the appliance's finished appearance. It snaps into place over the hinge area for a clean, secure fit. What it does

• Covers and protects the hinge mechanism from dirt and debris.
• Restores the appliance's finished appearance when the original cover is cracked or broken.
• Helps prevent accidental contact with moving hinge parts.
• Common symptom: visible broken or missing hinge trim exposing the hinge.

• One hinge cover assembly.

• Disconnect power (and water, if appliance type requires) before starting any repair.
• Remove any outer panels or trim as needed to access the hinge per the appliance service instructions.
• Handle plastic trim pieces carefully to avoid cracking during removal/installation.

This hinge cover assembly replaces a worn or damaged lid hinge cover to restore a smooth, finished look and protect the hinge area from debris and pinching. It helps keep the hinge area sealed and reduces snagging on the lid edge. What it does:

• Covers and protects the lid hinge and pivot area from dirt and moisture
• Restores a clean appearance where a cracked or missing hinge cover was visible
• Helps prevent clothing or hands from catching on the exposed hinge
• Can reduce rubbing noise caused by contact with a damaged cover

• Basic removal of the lid or access panel may be required; follow for proper disassembly
• Use appropriate hand tools and keep small fasteners secure during reassembly
• Disconnect power (and water for washers) before starting work to avoid injury

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

This is a door assembly that has been manufactured by LG for use with refrigerators. The door assembly includes multiple parts required for replacing the entire door, such as the inner liner and the outer panel. A working door is necessary for the refrigerator to maintain cold enough temperatures inside. If the current door is dented, bent, detached, or otherwise broken, it should be immediately replaced. This replacement might require two people, as the door is heavy. Take proper safety precautions, such as wearing work gloves and disconnecting the appliance from the power source.As a genuine OEM part, this door assembly has been sourced directly from the manufacturer and is only sold individually. This door assembly is manufactured from high-quality and durable materials to ensure durability. It is intended for use with refrigerators manufactured by LG.

The refrigerator door gasket seals the gap between the door and cabinet to keep cold air in and humid air out, helping maintain temperature, reduce frost and condensation, and restore a tight, reliable door close.

• Creates an airtight perimeter seal to prevent warm air leaks
• Helps stabilize interior temperature and humidity
• Minimizes frost buildup and condensation around the door
• Common symptoms: torn or deformed seal, door not sealing, moisture/frost near door, rising temps

What's included: 1 door gasket Installation notes:

• Disconnect power before servicing
• Allow the new gasket to warm to room temperature; soften in warm water or with gentle, low heat to relax folds
• Remove the old gasket and thoroughly clean the mounting channel/mating surfaces
• Seat the new gasket starting at the corners, then along the sides; ensure it's fully engaged and even all around, and check door alignment/seal

Restore a tight, reliable seal on your refrigerator door with this replacement gasket. A fresh gasket stops cold-air leaks that lead to frost, condensation, and temperature swings—helping your fridge run smoothly and keep food at the right temperature. What it does:

• Seals the gap between the door and cabinet to keep cold air in and warm air out
• Helps maintain consistent interior temperature and humidity
• Reduces frost and condensation around the door opening
• Common symptoms: torn or warped gasket, door not closing flush, moisture at the seal, frost buildup, or the unit running more than usual

• 1 door gasket

• Disconnect power before starting and clear items from the door
• Lay the new gasket flat and gently warm it (hot water or low-heat hair dryer) to relax folds
• Starting at the corners, press the gasket lip fully into the door channel and work evenly around
• Perform a paper-slip test around the perimeter and adjust door alignment if needed; avoid overheating the gasket

The Refrigerator Flipper Assembly is an OEM part for LG refrigerators. This assists in the smooth opening and closing of the refrigerator door. It ensures an airtight seal when the door is closed, preventing cool air from escaping and maintaining the refrigerator's internal temperature. 

Causes of a malfunctioning Refrigerator Flipper Assembly can range from physical damage, such as cracks or breakage, to wear and tear from regular use.

Symptoms of a bad Refrigerator Flipper Assembly include:

• Difficulty in opening or closing the refrigerator door
• A noticeable gap when the door is supposed to be sealed shut
• Increased energy consumption as the refrigerator works harder to maintain its temperature
• Spoilage of food items quicker than expected due to poor temperature regulation

This OEM LG part is also compatible with some Kenmore models.

This replacement drawer guide restores proper tracking and smooth operation to a refrigerator or freezer drawer. It helps keep the drawer aligned and reduces scraping, sticking, or uneven movement for reliable daily use. What it does:

• Guides the drawer along its track so it opens and closes smoothly
• Replaces a worn, cracked, or bent guide that can cause sticking or misalignment
• Reduces drawer rattling and scraping against the cabinet
• Helps prevent drawer drops or catching when pulling open or pushing closed

• Unplug the appliance or switch off power before servicing to avoid electrical hazards
• Remove the drawer and any screws or retaining clips holding the old guide; keep hardware if it's reusable
• Align the new guide on the track and secure with the original screws or clips; do not force parts into place
• Test the drawer operation before returning contents; recheck alignment and hardware if movement is still obstructed

The Door Bin is an OEM part for LG refrigerators. It provides convenient storage for items accessed regularly, from condiments to snacks.

Causes of a faulty door bin can include plastic cracking from extended usage, broken slide pegs, or a loose assembly. Regular temperature changes may compromise durability over time.

Symptoms of a problematic door bin include:

• Difficulty fully extending or retracting on glide tracks
• Contents are at risk of falling during opening/closing
• Rattling or vibrations while retrieving items

This LG part is also compatible with some Kenmore models.
 

STOPPER ASSEMBLY,DOOR

STOPPER ASSEMBLY,DOOR

This hinge cam fits the door hinge and provides the lift/settle action that helps the door open and close smoothly. Replacing a worn cam can reduce clicking and restore consistent door movement and alignment.

• Provides cam action at the hinge for smooth door travel
• Helps the door seat closed and maintain alignment
• Common symptoms include clicking/knocking at the hinge, rough or uneven door movement, or slight door sag
• Visual wear such as flat spots or grooves on the cam is a typical failure sign

• Disconnect power to the appliance before servicing
• Support the door to prevent injury; remove hinge cover and hardware as needed
• Note the cam's orientation and any washers/spacers and transfer them to the new part
• After installation, verify door operation and gasket alignment; adjust hinge if needed

The Door closer is an OEM part for LG refrigerators, this part prevents the refrigerator door from swinging open too widely. By limiting the door's range of motion, the Door Stop ensures that the door opens smoothly and safely, contributing to the longevity of the appliance and maintaining the aesthetic integrity of your kitchen space.

Causes of a bad Door closer can stem from physical damage, wear and tear over time, or loosening of the component due to repeated use. 

Symptoms of a bad Door closer include:

• The refrigerator door swinging open too far
• Damage or marks on adjacent walls or furniture from the door hitting them
• Increased wear on the refrigerator's hinges due to uncontrolled door movement

This OEM LG part is also compatible with some Kenmore models.

This rail slide replaces a worn or broken drawer track to restore smooth opening and reliable support for a refrigerator or freezer drawer. It helps the drawer glide smoothly and keeps contents stable during use. What it does:

• Guides and supports the drawer for smooth, linear movement
• Restores even alignment to prevent sticking, binding, or uneven travel
• Reduces rattling and helps the drawer stay fully seated when closed
• Addresses symptoms like a sagging, hard-to-pull, or off-track drawer

• High-level replacement — remove the drawer and fasteners to swap the rail
• Keep small screws and clips organized and reuse original hardware unless replacements are provided
• Wear gloves to protect hands and avoid damaging painted surfaces

This slide rail restores smooth, stable drawer or rack movement so the compartment opens and closes without binding. It replaces a worn or damaged rail to improve alignment and support. What it does

• Guides and supports a drawer or oven/rack for even, controlled sliding
• Reduces sticking, scraping, or uneven travel when opening or closing
• Helps prevent the drawer or rack from sagging or coming off the track
• Works as a mechanical replacement when the original rail is bent, cracked, or worn

• One slide rail

• Disconnect power or unplug the appliance before beginning any repair
• Remove the affected drawer or rack to access mounting screws and clips
• Match rail orientation and secure with the original fasteners; do not overtighten
• Test operation after installation and reassemble any removed components

This ice maker gear drives the ejector blades that push ice from the tray into the bin. Replacing a worn or broken gear restores proper harvest cycles and stops grinding or slipping during ejection. What it does:

• Turns the ice maker ejector to release ice cubes during the harvest cycle.
• Stops or reduces grinding noises and slipping when the gear teeth are stripped or damaged.
• Helps restore regular ice production when the ejector no longer rotates.
• Works as the replacement driven gear in compatible LG ice maker gear trains.

• Disconnect power before servicing the ice maker to avoid shock or injury.
• Remove the ice maker assembly to access the gear; follow OEM instructions for disassembly.
• Inspect the mating gear, motor shaft, and ejector assembly for wear—replace additional damaged parts as needed.
• Use the matching part number to ensure fit.

This center hinge assembly secures and allows smooth pivoting of the refrigerator's center door, restoring proper door alignment and closing. It replaces a worn or damaged hinge to reduce sagging and improve sealing. What it does:

• Provides the pivot point for the refrigerator's center door, maintaining correct door movement and alignment
• Helps the door close evenly to preserve the gasket seal and internal temperature
• Replaces broken, bent, or worn hinge hardware that can cause door sag or rubbing
• Works with existing hinge pins and mounting points to restore original function

• One center hinge assembly

• Requires basic hand tools; follow manufacturer instructions for removal and installation
• Support the door while removing or installing the hinge to prevent injury or damage
• Ensure all fasteners are tightened securely and door alignment is checked after installation
• Disconnect power if required by the appliance manufacturer before servicing

This center hinge assembly secures and pivots the upper/center refrigerator door, restoring proper door alignment and smooth opening. Designed to replace a worn, bent or broken center hinge to improve sealing and operation. What it does:

• Provides a mounting pivot for the upper/center refrigerator door to ensure correct swing and alignment
• Helps maintain an even door gap for a proper seal and consistent cooling
• Replaces damaged, bent or worn hinge components that cause rubbing, sagging, or noisy door movement
• Works with factory hinge pins and covers to restore original door function

• One center hinge assembly

• Installation requires removing the door and supporting it; have a helper to prevent damage or injury
• Use appropriate hand tools; avoid overtightening fasteners which can bind the hinge
• Inspect adjoining hinge pins and mounting screws; replace if worn for best results
• Disconnect power or follow manufacturer safety steps if working near electrical components

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This upper hinge assembly secures and guides the refrigerator door at the top, restoring proper alignment and smooth opening. Replace a worn hinge to stop sagging doors and improve sealing and operation. What it does:

• Provides the top pivot point for the refrigerator door, keeping it aligned during opening and closing
• Restores proper door clearance and prevents rubbing or misalignment
• Helps maintain a tight door seal to reduce cold air loss
• Addresses symptoms like a sagging or uneven door, noisy movement, or difficulty closing

• Disconnect power to the appliance before beginning repairs to prevent injury.
• Support the door while removing and installing the hinge to avoid dropping or damage.
• Use appropriate hand tools; do not overtighten fasteners to prevent stripping.

Replacement refrigerator door hinge that restores smooth pivoting and proper door alignment, helping the door open and close reliably and maintain an airtight seal to preserve cooling performance. What it does:

• Supports the refrigerator door and allows it to pivot smoothly.
• Replaces worn, bent, or damaged hinges that cause door sag or misalignment.
• Helps reduce noisy or grinding door operation when the hinge is failing.
• Promotes an even door seal to help maintain internal temperature consistency.

• Unplug the appliance and remove food from nearby shelves before starting work.
• Support the door while removing hinge fasteners to prevent dropping or damage.
• Reinstall using the original hardware; align the door and tighten fasteners securely but avoid overtightening.

This replacement spring provides the tension for a door hinge, helping the door open smoothly and stay closed for a proper seal and consistent appliance performance.

• Applies controlled tension to the hinge mechanism for smooth door movement
• Helps the door stay closed and aligned against the gasket
• Worn or broken spring symptoms can include the door dropping open, not staying closed, an uneven gap, or squeaking/binding at the hinge
• Restores normal feel and operation to the door

• Disconnect power and allow the appliance to cool completely before servicing
• Support the door; removal of the door or hinge arm may be required
• Use caution—hinge springs are under significant tension; wear gloves and eye protection
• Replacing both springs together helps maintain balanced tension

This sub control board is a printed circuit board that supports the appliance's main controls by managing low-voltage power and signals for the user interface. Replacing a failed board restores consistent, responsive operation of the control panel and display.

• Regulates low-voltage power and signal routing for the control panel/display
• Interfaces with the main control to interpret user inputs
• Can address unresponsive buttons or a unit that won't start
• Correct intermittent control-panel behavior or control-related error codes

• Disconnect power at the breaker or unplug the appliance before service
• Use ESD protection; handle the PCB by its edges to avoid static damage
• Photograph wiring and move connectors one at a time to the new board
• Verify all standoffs, screws, and connectors are fully seated before restoring power

This overload protector is a motor thermal cut-off that helps prevent motor overheating by interrupting power when temperatures get too high. It restores normal operation after the motor cools, helping protect the motor from heat damage. What it does:

• Senses excess motor temperature and interrupts power to prevent overheating
• Commonly used when a washer or motor hums, won't spin, or stops mid-cycle
• Protects the motor and associated components from heat-related failure
• Resets or is replaced after a thermal fault clears, depending on design

• Disconnect power before accessing the motor or electrical components
• Handle and mount the protector per OEM orientation to ensure proper thermal contact
• Inspect motor and wiring for underlying faults before replacing

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

The Fan Motor Assembly is an OEM part for LG refrigerators. It is responsible for circulating air throughout the refrigerator and freezer compartments to maintain consistent temperatures. By ensuring proper airflow, the fan motor helps to keep your food fresh and evenly cooled.

Over time, fan motors can wear out or become damaged due to factors such as dust buildup, electrical issues, or general wear and tear from continuous use. A faulty fan motor can lead to uneven cooling, increased energy consumption, and potential spoilage of food.

Symptoms of a bad fan motor include:

• Unusual noises coming from the refrigerator
• Inconsistent temperatures in the fridge or freezer
• The refrigerator running constantly or cycling on and off frequently
• Frost buildup in the freezer section

This OEM LG part is also compatible with Sears/Kenmore.

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

The Drier Assembly is an OEM part for LG refrigerators. This part removes moisture and contaminants from the refrigerant, ensuring the system operates efficiently and effectively. The drier assembly helps maintain the proper function of the compressor and other cooling components, contributing to the longevity and performance of the refrigerator.

Causes of a bad drier assembly can include clogs from debris, wear and tear over time, or contamination from moisture or refrigerant leaks.  

Symptoms of a bad drier assembly include:

• The refrigerator not cooling properly
• Frost or ice buildup on the evaporator coils
• Increased noise from the compressor
• Reduced efficiency and higher energy consumption
• You should replace the drier assembly if it becomes faulty or damaged.

This OEM LG part is also compatible with select Sears/Kenmore models.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

The Evaporator Fan Blade is an OEM replacement part for LG refrigerators. It is a key component located inside the refrigerator that works to circulate cold air evenly throughout. The fan blade spins rapidly to distribute chilled air from the evaporator coil and refrigeration system, ensuring proper airflow and consistent temperatures across all shelves and compartments.  

Symptoms of a bad evaporator fan blade include:

• Inconsistent or improper interior cooling temperatures 
• Hot or warm spots developing inside the refrigerator
• Strange noises such as clicking or grinding emanating from the rear wall

Causes of a bad evaporator fan blade can be wear and tear over time, an accumulation of dust or debris on the blades restricting airflow, or accidental damage like dents or cracks to the blades affecting their ability to spin smoothly.

This OEM LG part is also compatible with select Sears/Kenmore brand models.

The Fan and Grille Assembly is an OEM component designed for LG refrigerators. This assembly circulates air within the refrigerator compartment to maintain even cooling temperatures. 

Causes of a bad fan and grille assembly can include failure of motorized fan components over time, buildup of dust or debris restricting airflow, or physical damage to fan blades.

Symptoms of a bad fan and grille assembly include:  

• Development of warm spots within the fridge
• Excessive frost or ice buildup inside 
• Louder than normal operating sounds
• Inability to maintain proper temperature settings

Replace yours today with this genuine OEM LG assembly to restore optimized air circulation for balanced cooling. This replacement assembly is compatible with Kenmore, Frigidaire, and GE refrigerator models. Proper airflow is essential for energy efficiency and food freshness.

Incudes motor and rear wall assembly.

The Dispenser Micro Switch is an OEM part for LG refrigerators. It is a component of the ice and water dispensing system, responsible for activating the dispenser when the lever is pressed. 

Causes of a bad Dispenser Micro Switch can include mechanical wear from frequent use, failure due to moisture or debris affecting the switch’s contacts, or electrical faults that prevent proper signaling.

Symptoms of a bad Dispenser Micro Switch include:

• The dispenser not releasing ice or water when the lever is pressed.
• Continuous dispensing or dripping after the lever is released.
• Intermittent or no response from the dispenser controls.

This OEM LG part is also compatible with Sears/Kenmore.

This fan assembly circulates air within the appliance to maintain steady temperatures and efficient cooling. Replacing a worn or noisy unit restores proper airflow, reduces hot or cold spots, and helps protect other components. What it does:

• Moves air through the appliance and across cooling components for even temperature distribution
• Helps remove heat and moisture as designed for efficient operation
• Replaces a seized, slow, intermittent, or noisy fan/motor assembly
• Common symptoms include weak or no airflow, temperature fluctuations, or abnormal humming/rattling sounds from the fan area

• 1 fan assembly

• Disconnect power before servicing; allow any iced or brittle plastic areas to warm/defrost
• Remove access panels/ducts as needed; note wire routing and take photos for reference
• Transfer any reusable brackets, grommets, or screws from the original assembly
• Ensure the blade spins freely and wiring is clear of the fan path before reassembly and testing

The Evaporator Fan Motor Assembly is an OEM replacement part for LG refrigerators. This assembly is responsible for circulating cold air from the evaporator coils throughout the refrigerator and freezer compartments. By doing so, it ensures that both compartments maintain the desired temperatures and that the cooling process is efficient.

Causes for a malfunctioning Evaporator Fan Motor Assembly can include motor wear from continuous operation, electrical issues like faulty wiring, obstructions preventing the fan blades from turning, or damage to the fan blades themselves.

Symptoms of a bad Evaporator Fan Motor Assembly include:

• Inconsistent temperatures in the refrigerator or freezer compartments
• Unusual noises, such as humming or buzzing, coming from the back of the refrigerator
• Reduced cooling efficiency, leading to food spoiling faster
• Frost buildup in the freezer due to poor air circulation

This OEM LG part is also compatible with Sears/Kenmore model refrigerators.

Damper motor support secures the damper motor assembly inside the refrigerator, keeping the air-control damper aligned so it opens and closes correctly. Replacing a damaged support restores proper airflow control and reduces noise. What it does:

• Secures and positions the damper motor assembly so the air-control damper moves smoothly.
• Keeps the motor and damper aligned to help prevent rattling, grinding, or loose motor noise.
• Supports consistent airflow between compartments to assist with even cooling.
• Resolve damper movement problems like the damper not opening or closing fully.

• Disconnect power to the appliance before starting work; remove food and shelves as needed for access.
• Remove the interior access panel to reach the damper assembly; handle plastic tabs and clips gently to avoid breakage.
• Align the motor and damper during reassembly and secure all fasteners; test damper operation before replacing panels and shelving.

This damper motor support replaces a broken or warped mount for the refrigerator's air damper assembly. It holds the damper motor and door securely so the system can meter freezer air into the fresh food compartment.

• Secures and aligns the air damper motor/door within the duct
• Helps ensure proper opening/closing of the damper to regulate airflow and temperature
• Damage can contribute to a warm or too-cold refrigerator and inconsistent temperatures
• May cause clicking or buzzing from the damper area or a visibly loose assembly

• Disconnect power to the refrigerator before servicing
• Access the damper behind the fresh food compartment duct/cover; remove shelves as needed
• Note wiring and orientation; transfer the existing damper motor and door to the new support and reuse fasteners
• Ensure the door moves freely and seals before reassembly; restore power and verify airflow

This sheath-style heater melts frost from the evaporator during automatic defrost cycles to keep airflow clear and temperatures stable. Replacing a failed heater helps stop recurring ice buildup and restore consistent cooling performance.

• Heats the evaporator to melt accumulated frost/ice during defrost
• Keeps air passages clear to maintain proper temperatures
• Helps prevent frost-packed evaporator covers and reduced cooling
• Common symptoms: heavy frost behind the freezer panel, fan noise from ice contact, weak cooling, long run times

• Disconnect power before servicing; allow any sharp edges to be avoided with cut-resistant gloves
• Access is typically behind the freezer's rear interior panel; remove shelves/drawers and panel to reach the evaporator
• Transfer any clips/sensors attached to the heater in the same positions; avoid bending fins or puncturing refrigerant lines
• Ensure connectors are fully seated and the heater is secured before restoring power and monitoring operation

This LED assembly is a backlight strip used to illuminate the display for clear, even picture brightness. Replacing a faulty strip restores proper screen illumination and can eliminate dark spots or missing segments. What it does:

• Provides the LED illumination source behind the LCD panel for even brightness
• Restores lost or uneven backlighting caused by failed LEDs or damaged strips
• Commonly replaces parts that cause dimming, flickering, or no light on power-up
• Connects to the display's LED driver board to receive power and signals

• Disconnect power and remove the display panel before replacing
• Handle the strip and connector carefully to avoid bending or damaging LEDs and flex cables
• Observe ESD precautions and avoid touching LED surfaces or circuit traces
• Reassemble panels and test before finalizing to ensure proper alignment and function

This power cord assembly provides the mains connection for compatible LG appliances, restoring reliable power delivery so the unit can run safely and consistently. Use when the original cord is damaged or the appliance loses power. What it does:

• Replaces a worn, frayed, or damaged power cord to restore safe electrical connection
• Carries line, neutral, and ground (where applicable) from the outlet to the appliance
• Helps resolve symptoms such as no power, intermittent power, or visible cord damage
• Maintains factory-fit routing and terminal connections for proper installation

• One power cord assembly as pictured

• Disconnect power at the breaker or unplug the appliance before installing
• Tighten terminal screws securely and route the cord to prevent pinching or chafing

This ice maker lever is the mechanical arm that controls ice production by interacting with the ice maker's on/off and level-sensing mechanism. Replacing a broken or missing lever restores proper operation and helps prevent overfilling or no-ice conditions.

• Acts as the ice maker's shut-off arm to regulate ice production
• Lowers to allow ice making; raises to stop when the bin is full
• Common symptoms: ice maker won't stop making ice, no ice when arm is stuck up, broken/missing lever, lever won't stay in position
• Helps ensure consistent, reliable ice production control

• Disconnect power and shut off water before service
• Remove the ice bin to access the ice maker; gently release the lever from its pivots/linkage
• Note lever orientation; transfer and reuse any original springs, clips, or fasteners
• Reinstall components, restore power, and verify free up/down movement of the arm

This refrigerator ice maker assembly automatically fills, freezes, and harvests ice cubes into the bin. Replacing a failed ice maker restores steady ice production and proper shutoff when the bin is full.

• Automates the ice-making cycle: fills the mold, freezes water, and ejects cubes into the bin
• Monitors bin level and stops production when full
• Helps address symptoms such as no ice production, not cycling/harvesting, or cubes not ejecting
• Can also help with intermittent or inconsistent ice output

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the ice bin, unfasten mounting screws, and disconnect the wire harness
• Transfer existing brackets or covers if required; reconnect harness and secure the assembly
• Align the fill tube with the icemaker inlet; restore power/water and allow up to 24 hours for normal ice production

This sensor PCB assembly detects and relays sensor signals to the appliance control system, restoring accurate sensor feedback and communication when the original sensor board fails or malfunctions. Designed as a direct replacement board. What it does:

• Reads sensor inputs and converts them to signals the main control board can interpret.
• Replaces a failed or intermittent sensor board that causes incorrect readings or sensor-related error codes.
• Can resolve symptoms such as unexpected sensor faults, control errors, or appliances not responding to sensor changes.
• Matches the OEM board function; verify model compatibility before ordering.

• Always disconnect power before servicing to avoid shock or shorting the board.
• Use ESD precautions and handle the PCB by its edges to prevent static damage.
• Ensure all connectors are fully seated and the board is mounted in the original orientation.

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances. 

This connector tube provides a sealed water path between refrigerator water components to restore proper water flow and reduce leaks. It's a direct-fit replacement when your existing connector is cracked, clogged, or damaged. What it does

• Re-establishes a secure water connection between dispenser/ice-making components.
• Restores water flow so the ice maker and dispenser can fill properly.
• Prevents drips and leaks from damaged or degraded tubing joints.
• Helps eliminate intermittent filling or reduced water flow caused by collapsed tubing.

• One connector tube.

• Disconnect power and shut off the water supply before beginning any work.
• Use proper fittings or clamps and tighten securely—avoid over-tightening plastic fittings.
• After installation, turn on the water and check all connections for leaks; discard any damaged or brittle tubing.

This water line holder secures and routes the refrigerator's plastic water tube so it stays protected and out of the way. Replacing a damaged holder helps prevent kinks and leaks and keeps water flowing to the dispenser and icemaker.

• Anchors and guides the water tube along the cabinet/door to prevent rubbing and kinking
• Helps maintain proper water flow to the dispenser and ice maker
• Replace if the holder is cracked, missing, or the tube won't stay seated
• Symptoms can include leaks or drips near the hinge/backs, slow or no dispensing, or visibly loose tubing

• Disconnect power and turn off the household water supply before servicing
• Access the holder (often behind a hinge cover, kick plate, or rear panel)
• Note tube routing, then release/remove the old holder and seat the tube in the new holder; reuse existing hardware if present
• Restore water and power; check for leaks and normal dispenser/ice operation

The Water Valve Assembly is an OEM part for LG French door refrigerators. It is an important component that controls water flow to the refrigerator's internal dispenser and ice maker. The valve precisely regulates the amount of water reaching the filter assembly and allows for dispensing on demand. 

Causes of a bad water valve can include normal wear over time, mineral buildup restricting flow, or failure of electronic components regulating the valve. 

Symptoms of a bad water valve include:

• No or inconsistent water dispensing  
• Ice maker not functioning or producing empty cubes
• Water leaks inside refrigerator walls
• Error messages related to water supply issues

 This genuine LG is also compatible with some Kenmore side-by-side models.

This injection tube routes water to the ice/water system so your appliance can make ice and dispense water reliably. It's a direct-fit replacement that restores proper water delivery when the original tube is damaged or clogged. What it does:

• Carries water from the supply path to the ice maker or dispenser assembly
• Maintains correct flow pressure for consistent ice production and dispensing
• Helps prevent leaks when installed intact and undamaged
• Commonly replaced for visible cracks, kinks, or reduced water flow

• Disconnect power and shut off the water supply before beginning any work
• Handle the tube gently to avoid kinks; route exactly as the original to prevent interference
• Use only the supplied fittings and clamps; replace any damaged connectors

This replacement cover filter secures and protects the unit's internal air filters while maintaining correct airflow. It restores the sealed fit of the filter compartment to help the appliance run as intended. What it does:

• Holds the internal filter in place so air passes through the filter media
• Prevents large debris and foreign objects from reaching internal components
• Helps maintain designed airflow path for consistent performance
• Can reduce rattling or vibration caused by a loose or damaged cover

• Unplug the appliance or disconnect power before starting
• Remove the front panel or filter access per the owner's manual to reach the cover
• Align tabs and snap or fasten the cover securely; do not force parts
• Do not operate the appliance with missing or damaged filter cover

The Refrigerator water filter head is an OEM part for LG refrigerators featuring a water filtration system. As the connection point between the refrigerator door dispenser and replacement water filters, the head houses the electronic monitoring components that detect filter status and life.

Causes of a bad water filter head can include mineral deposits clogging sensor functions over time. Electrical failures from power surges or fluctuations may also affect integrated circuits and components.

Symptoms of a bad filter head include:

• Inability to dispense water or ice from the refrigerator door
• "Change filter" notifications that do not sync with actual filter replacements
• Fault codes displayed related to water or ice supply issues
• Water filtration that is compromised, allowing contaminants

This LG part is also compatible with some Kenmore models.

This water filter assembly replaces the refrigerator's water filtration module to help restore clear-tasting water and steady flow. Fits models that use the AGF80300705 assembly and installs at the refrigerator water inlet. What it does:

• Filters sediment and common taste/odor contaminants to improve drinking water quality
• Restores reduced water flow caused by a clogged or failing filter module
• Helps reduce visible particulates and cloudiness in dispensed water
• Prevents unfiltered water from reaching the dispenser/ice maker when installed

• Turn off refrigerator water supply before replacing the assembly to avoid leaks
• Hand-tighten connections; avoid overtightening fittings to prevent damage
• Run and discard the manufacturer-recommended initial volume of water after install to flush the system

This genuine replacement filter cover secures and protects the unit's air filter, helping keep the filtration system sealed and operating as designed. Restores proper fit and helps maintain airflow through the filter assembly. What it does:

• Holds the air filter in place and protects the filter media from debris
• Helps maintain correct airflow through the filter chamber for effective filtration
• Prevents gaps that can allow unfiltered air to bypass the filter
• Restores a secure fit if the original cover is cracked, warped, or missing

• One filter cover

• Disconnect power to the appliance before removing or replacing the cover
• Remove the old cover by releasing any clips or tabs, then snap or slide the new cover into place
• Inspect surrounding seal/gasket and filter media for damage while installing
• If clips or tabs are damaged, replace them before operating the appliance