Parts for Whirlpool 5KSM150PSCPK0: 02 - Color Variation Parts

A replacement housing that secures and protects the appliance's internal components and mounting points. Restores structural support and helps reduce vibration or movement caused by damaged or cracked housings. What it does:

• Provides a stable mounting surface for internal assemblies and fasteners
• Protects internal parts from debris and accidental contact
• Restores proper alignment to reduce noise, vibration, and movement
• Addresses visible cracks, broken mounting tabs, or warped housing edges that compromise fit

• One housing

• Disconnect power and water before beginning any repair
• Handle edges carefully; use gloves to avoid cuts from sharp sheet-metal or plastic
• Basic hand tools required; follow the appliance service manual for disassembly/reassembly
• If mounting tabs or adjacent parts are damaged, inspect and replace those items as needed for a complete repair

Fix grinding noises or bowl rotation issues with this gearcase housing. Protects motor gears and restores smooth operation in your stand mixer.

Replaces the front grille housing on your stand mixer. Needed when the original is cracked, warped, discolored, or missing. Almond creme finish.

Empire red housing for stand mixers. Replaces cracked, chipped, or discolored exterior covers. Restores appearance and protects internal components.

Imperial gray body housing cover for stand mixers. Replace this outer shell if cracked, scratched, discolored, or damaged. Restores mixer appearance.

If your stand mixer runs loud or vibrates excessively, a cracked motor housing may be the cause. This housing secures and protects the motor assembly.

Fix excessive vibration or unusual motor noise with this stand mixer motor housing. Secures and aligns the motor for stable, quiet operation.

Fix a noisy or vibrating mixer with this gearcase housing. Protects internal gears and keeps them aligned for smooth mixing. Moderate DIY repair.

Onyx black bowl for stand mixers. Replaces cracked, chipped, or worn mixing bowls. Direct fit replacement for compatible KitchenAid models.

Cosmetic band trim that covers the edge of your stand mixer body for a clean finish. Replace if cracked, chipped, discolored, or missing.

Replace your stand mixer's motor housing cover if cracked, broken, or missing. This protective cover installs over the motor assembly to complete the look.

This end cover protects and finishes the exposed end of the appliance component, keeping wiring and internal parts shielded while restoring the original appearance. It fits into the component housing and snaps into place for a clean finish. What it does:

• Covers and protects the exposed end of the component housing to help prevent dust and debris entry
• Helps keep wiring and terminals shielded from accidental contact
• Restores the original appearance where the original cover was cracked, discolored, or missing
• Matches the OEM color scheme for a factory look

• Designed to snap or screw into the component housing—verify orientation before seating
• Use basic hand tools; avoid prying on tabs to prevent breakage
• Disconnect power to the appliance before attempting removal or installation
• If tabs or mounting points are damaged, replace associated housing parts as needed

This replacement cover is an access panel that protects internal components and restores the appliance's appearance. It keeps wiring and mechanical parts shielded while maintaining a clean exterior surface. What it does:

• Covers and protects internal components from dust, debris and accidental contact
• Restores the appliance's exterior finish after damage or removal
• Helps reduce rattles or vibration caused by loose or broken panels
• Provides a secure mounting surface for adjacent panels and controls

• Disconnect power (and water if applicable) before beginning service
• Use proper hand tools; avoid overtightening fasteners to prevent cracking
• Handle edges carefully to avoid cuts and to prevent cosmetic damage
• Refer to your model's service manual or parts diagram for correct placement and fastener locations

Replacement cover for stand mixer housing. Protects internal components and provides finished appearance. Needed when original is cracked or broken.

Imperial gray finish bowl for stand mixers. Replace cracked, chipped, or discolored mixing bowls. Attaches to mixer base for ingredient preparation.

Replace the end cover on your stand mixer when the original is cracked, broken, or missing. This cosmetic panel installs on the motor housing end.

Cobalt blue cover that restores your mixer's exterior appearance. Replaces the original panel when it's cracked, faded, worn, or missing.

Replacement access panel cover for stand mixers. Shields internal wiring and controls while restoring exterior appearance. Replaces cracked or missing covers.

Factory-matched Almond Crème touch-up paint for stand mixers. Covers small chips, scratches, and worn spots on Almond-finish appliances for a cleaner look.

White plastic back cover for stand mixers. Protects internal components at rear of motor housing. Replace if cracked, broken, or missing.

Mixer not spinning or making grinding noises? This planetary gear assembly drives the beater rotation. Moderate DIY repair in about 45 minutes.

Replace the gray housing cover on your stand mixer. This cosmetic shell protects internal components and completes the exterior appearance when damaged.

Fix grinding noise and poor mixing with this planetary assembly. Restores drive alignment for smooth mixer operation. Moderate DIY repair for most users.

If your mixer won't spin or makes grinding noises, the planetary gear assembly may be worn. This part transfers motor power to attachments. Moderate DIY.

Fix mixer wobbling or grinding noises with this planetary gear assembly. Essential for smooth mixing action. Moderate repair with periodic greasing.

Fixes grinding noise and erratic mixing. This planetary gear assembly restores smooth rotation in your stand mixer. Moderate DIY repair with proper tools.

White planetary gear assembly for stand mixers. Installs in the mixer head to drive beaters and attachments. Replace if cracked, damaged, or worn.

Gray housing cover for stand mixers. Replaces cracked, chipped, or discolored exterior covers. Restores the appearance of your mixer's body shell.

Fix a stand mixer that's making grinding noises or won't mix properly with this gearcase assembly. Common repair for worn internal gears.

If your mixer won't lift or lower properly, or makes grinding noises, the lower gearcase may be worn. This assembly restores smooth operation.

Decorative grille that covers the control area on your stand mixer. Replace if cracked, damaged, or loose to restore a clean, finished appearance.

Almond Creme finish panel for stand mixers. Restores exterior appearance when original panel is scratched, worn, or discolored. Direct replacement.

This pedestle is the replacement agitator post that supports and centers the washer agitator, restoring proper agitation and load stability for top-load washers. It's a direct-fit part used during agitator assembly repairs. What it does:

• Centers and secures the agitator on the transmission shaft for effective wash action
• Helps transmit agitation motion from the transmission to the agitator
• Commonly replaced when the agitator wobbles, slips, or does not rotate properly
• Restores stable operation without requiring a full agitator or transmission replacement

• One pedestle (agitator post) as shown

• Disconnect power to the washer before beginning any repair
• Remove agitator per manufacturer instructions to access and replace the pedestle
• Use appropriate hand tools; keep fasteners organized for reassembly

This pedestal feet assembly provides the lower support and leveling for a laundry pedestal, helping keep the pedestal stable and aligned beneath the washer or dryer. Designed to restore proper support and reduce rocking. What it does:

• Replaces damaged or worn pedestal feet that cause rocking, uneven height, or instability
• Provides adjustable support to help level the pedestal on uneven floors
• Protects floors by maintaining proper pedestal alignment and preventing scraping
• Restores safe, secure support for appliances installed on the pedestal

• Follow the appliance and pedestal manufacturer instructions; have a second person or proper support to prevent tip-over when removing or installing the pedestal
• Ensure the appliance is powered off and disconnected from utilities if appliance removal or repositioning is required
• Use basic hand tools; confirm all fasteners are tightened securely after installation

Replacement bowl for stand mixers in almond cream finish. Needed when original bowl is cracked, chipped, or discolored. Fits directly onto mixer base.