Parts for Whirlpool WTW5057LW0: Console And Water Inlet Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This replacement nut secures appliance parts and hardware to keep assemblies stable and prevent loose connections. It's a simple, direct replacement for worn or missing fastening hardware to restore proper fit and reduce vibration. What it does:

• Fastens mounting studs, brackets or panels to hold components in place
• Restores secure mechanical connections that can loosen over time
• Helps eliminate rattling, vibration and misaligned panels caused by missing or stripped hardware
• Provides a straightforward, durable replacement for corroded or damaged nuts

• Disconnect power to the appliance before beginning any repair
• Use the correct-size wrench or socket; ensure threads engage smoothly before tightening
• Tighten until snug—avoid overtightening that can strip threads or damage components
• Inspect mating threads and replace any damaged studs or hardware for a reliable repair

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Washer Encoder Control Board is an OEM part for Whirlpool washing machines. As the central processing component, it regulates all cycle phases including wash, rinse, and spin speeds through electronic encoding commands. 

Symptoms of a bad encoder control board include:

• Inability to start or progress through cycle phases
• Failure to produce programmed wash motions  
• Not reaching intended rinse or spin speeds
• Unexpected behaviors like fast-forwarding

Causes can involve damage from water exposure over many years, power surges interfering with circuitry, or failures of electronic chips and sensors.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Amana, and some Kenmore washers.

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness is the main wiring assembly that connects controls and components, restoring electrical pathways for safe, reliable appliance operation. It replaces a damaged or frayed harness to help resolve intermittent or non-functioning electrical issues. What it does:

• Provides factory-style connections between control board and components for proper power and signal transmission
• Commonly replaces damaged, pinched, or burned wiring that can cause intermittent operation or loss of function
• Helps stop arcing, shorts, or erratic behavior caused by broken or loose connector leads
• Restores proper routing and secure connector fit to prevent future electrical faults

• One complete wire harness assembly

• Disconnect power (unplug or switch off breaker) before servicing to avoid shock or injury
• Compare new harness to the old one for connector types and routing; take photos before removal to aid reinstallation
• Route and secure harness away from heat sources, moving parts, and sharp edges to prevent wear
• Do not modify connectors or splice wires unless instructed by manufacturer

This replacement control knob restores a secure, easy-to-use grip for turning stove or oven controls so you can set temperatures and burners reliably. It replaces a worn, cracked, or missing knob to restore normal control operation. What it does:

• Provides a firm grip and clear pointer for adjusting oven or cooktop controls
• Replaces cracked, stripped, loose, or missing knobs that won't engage the control shaft
• Helps prevent accidental changes by fitting snugly on the valve or shaft
• Restores tactile feedback for accurate temperature or burner selection

• One control knob

• Disconnect power (or turn off gas supply) and ensure controls are cool before replacing
• Pull the old knob straight off the control shaft; align the new knob and push on until fully seated
• If knob is tight or stuck, gently wiggle while pulling; do not use excessive force or metal tools that could damage the shaft

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rear Panel is an OEM part compatible with Whirlpool washing machines. As the rear housing component, it protects internal mechanisms from debris while providing structure and stability to the cabinet. Its rigid design assists with even weight distribution to minimize vibrations. 

Symptoms of a bad rear panel can include:

• Warping or flexing of the panel material over time
• Cracks developing from pressure changes in the tub area
• Dents compromising the panel's integrity from heavy loads 

Causes of a bad rear panel washer stem from long-term use, with stress and strain accumulating from years of use. Agitator movement and unbalanced loads can warp the panel out of shape.

This OEM Whirlpool replacement rear panel helps restore the washer's protective barrier. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Control Board is an OEM part for Whirlpool washing machines. As the main controller, it regulates the operation of components like the pump motor, transmission, and clutch during all cycles. The control board uses sensors to monitor water levels and mechanical functions to advance cycles accurately.

Causes can be water damage, fluctuations in power supply, or general wear over extended usage.

Symptoms of a bad motor control board include:

• Washer not agitating or spinning clothes
• Inability to advance to different cycles
• Variable speed not working as expected
• Strange noises coming from mechanical parts

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

The Water Inlet Valve is an OEM part for Whirlpool front-loading washing machines. It is an electromagnetic valve that precisely controls water intake into the washer during designated points in the cycle. 

Causes of a bad water inlet valve can include mineral buildup disrupting valve function over many years of use. Exposure to varying water temperatures may also decrease lifespan.

Symptoms of a bad water inlet valve include:

• Inability to fully fill the washer tub as needed for optimal cleaning  
• Fluctuating or absent water levels lead to inefficient cycles
• Water pressure or temperature regulation is impacted 
• Valve seizing could result in flooding inside the washer

This OEM Whirlpool replacement valve restores precise fill control and pressure regulation. Compatible models include some Maytag, Amana, Jenn-Air, and select Kenmore machines. Replace yours to maintain peak washing performance.
 

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.