Parts for Jenn-Air JDRP548HM00: Cooktop, Burner And Grate Parts

This side compartment is a replacement refrigerator door shelf that restores secure storage on the door and keeps bottles, jars and other items organized. It fits into a compatible refrigerator door to replace a cracked, broken or missing shelf. What it does:

• Provides a stable shelf on the refrigerator door for bottles, jars and small containers
• Replaces a cracked, broken or missing door shelf that allows items to tip or fall
• Restores proper spacing and organization inside the door storage area
• Helps keep stored items contained when opening and closing the door

• One side compartment

• High-level, snap-in installation—inspect mounting pegs or clips for damage before installing
• Power does not usually need to be disconnected, but remove all items from the shelf and wear gloves to avoid sharp edges
• If mounting clips are damaged, replace clips or the entire assembly to ensure a secure fit
• Test door operation with the shelf loaded to secure installation

This side compartment is a direct-fit door bin that restores storage on the refrigerator door, keeping bottles and small items secure and organized. Durable molded plastic replaces cracked or missing bins for reliable everyday use. What it does:

• Replaces a cracked, broken or missing door bin to restore storage capacity and organization
• Holds bottles, condiments and small containers along the inside of the refrigerator door
• Prevents items from falling when the door opens and closes
• Matches the factory shelf design for correct fit and alignment

• High-level snap-in/screw-in replacement; remove existing bin then install new bin until it seats
• Disconnect power only if removal requires working near electrical components; otherwise power disconnection is not typically needed
• Handle carefully to avoid damage to adjacent door liners or gaskets

This brass burner orifice meters natural gas to the burner for correct flame size and reliable cooking heat. Replaces a worn or clogged orifice to restore consistent ignition and even burner performance. What it does:

• Controls gas flow to the burner for a stable, properly sized flame
• Helps correct low, uneven, or weak burner flames caused by a restricted orifice
• Prevents rich/sooty combustion from an oversized orifice
• Used where a 2.5k BTU natural gas flow rate is required for the burner

• Turn off gas and electricity before servicing; follow all safety precautions
• Remove burner cap and unscrew old orifice; install new orifice hand-tight then snug with appropriate tool
• Do not overtighten; check for gas leaks after installation using a leak-safe method

This orifice controls natural gas flow to a burner for a precise 17.5K BTU output, restoring proper flame size and consistent heating. Use when a burner produces weak, uneven, or no flame. What it does:

• Meter gas to the burner for a 17.5K BTU natural gas flame
• Helps correct low or uneven burner flames and improves heat output
• Commonly replaced when a burner won't light, sputters, or shows an unstable/yellow flame
• Works as the fixed orifice that matches appliance gas pressure and burner design

• Shut off gas supply and disconnect power before servicing
• Replace only with the correct orifice size for safe operation
• Use proper fittings and thread sealant rated for gas; check all connections for leaks

This is a 10" heavy-duty igniter wire used to connect the oven igniter to the control/safety device, ensuring reliable spark transfer for proper ignition. It replaces worn or damaged wiring to restore safe burner operation. What it does:

• Conducts the ignition current between the igniter and the control/safety module
• Helps the oven or range light and maintain a consistent flame
• Commonly replaced when ignition is intermittent, the oven won't light, or wiring is visibly damaged
• Heavy-duty construction reduces breakage and improves durability

• Turn off power to the appliance and shut off the gas supply before starting any repair
• Handle carefully to avoid damaging insulation or connectors; replace if frayed, corroded, or nicked
• Route and secure the wire away from moving parts and high-heat areas

This heavy-duty 15" igniter lead wire connects the oven/range igniter to the appliance wiring, providing a durable electrical path for reliable ignition. It replaces worn or damaged lead wires to restore consistent burner lighting. What it does:

• Carries ignition voltage from the control harness to the oven/range igniter
• Helps prevent intermittent or no-heat symptoms caused by cracked, frayed, or corroded wiring
• Designed for high-temperature areas near the oven or burner assembly
• Maintains a secure electrical connection for stable ignition performance

• Disconnect power and shut off gas supply before accessing the appliance
• Inspect and replace only when the wire shows visible damage, charring, or loose terminals
• Handle ceramic or insulated ends carefully to avoid cracking; ensure tight terminal connections

This burner head replaces a damaged or clogged surface burner to restore proper gas flow and even flames on a gas cooktop. It provides a stable burner base for the burner cap and helps maintain consistent heat for cooking. What it does:

• Directs gas to the burner ports so the burner cap produces an even flame
• Helps restore normal burner performance when flames are weak, uneven, or misdirected
• Works with the existing burner cap and igniter to light and sustain a steady flame
• Prevents flame lift and popping caused by warped or clogged burner openings

• One surface burner head

• Turn off the gas supply and disconnect power to the range before beginning work
• Allow the appliance to cool completely; remove the burner cap and replace the burner head, ensuring ports align correctly
• Hand-tighten and seat parts; avoid over-tightening and verify the burner cap sits flat on the head
• If the igniter or burner cap is damaged or cracked, replace those components as well for reliable operation

This surface burner head directs and shapes the gas flame for even heating on a gas cooktop. It restores proper flame pattern and helps burners light and heat cookware reliably. What it does:

• Replaces a damaged or warped burner head to restore consistent flame distribution.
• Helps correct uneven heating, sputtering flames, or flame lift caused by cracked or corroded heads.
• Works with compatible cooktop caps and grates to safely contain the burner flame.
• Fits the factory burner assembly to maintain proper spacing and ignition performance.

• One replacement burner head

• Turn off gas supply and power to the appliance before beginning any work.
• Clean surrounding surface and check burner cap and orifice for debris before reassembly.
• Hand-tighten and seat parts; avoid overtightening.
• Use only with compatible burner caps, grates, and factory-specified components.

This small plastic clip secures appliance panels, trim, or wiring to prevent movement and rattling, restoring proper fit and quiet operation. It's a simple, low-cost part that helps keep components held in place. What it does:

• Acts as a retainer to hold panels, trim pieces, or harnesses in position
• Prevents rattling, vibration noise, and loose or misaligned parts
• Helps maintain proper spacing and alignment of adjacent components
• Commonly replaced when clips are broken, cracked, or missing

• One clip/retainer

• Disconnect power (and water if applicable) before beginning any work
• Clip typically snaps into place; may require a flat screwdriver or trim tool to remove/install
• Inspect surrounding mounting points for damage before fastening replacement clip
• Replace all corresponding fasteners for even fit

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

The Control Panel is an OEM part for Whirlpool free-standing gas ranges. Mounted on the front fascia, it serves as the interface for all heating functions.  

Causes of a control panel failure can include crackling or damage over multiple years from constant heat and intermittent user contact. Debris or mineral deposits may also abrade sensitive components.

Symptoms of a bad control panel include: 

• Faulty or unresponsive knob/button sensors
• Burned-out digital displays or indicator lights  
• Responsiveness issues inputting functions
• Moisture or liquid intrusion behind the faceplate

Compatible also with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Kenmore gas models. 

This indicator light lamp assembly notifies you when a control or function is active and restores visible status feedback for your appliance. It's a small, direct-replacement lamp used on control panels and status indicators. What it does:

• Illuminates control-panel indicators so you can see operating status and selected settings.
• Replaces a dim, flickering, or non-working indicator light.
• Helps diagnose control and user-interface issues by restoring visible feedback.
• Fits into the panel socket and connects to the existing wiring harness.

• Disconnect power to the appliance before starting any repair to avoid shock.
• Access typically requires removing the control or trim panel; keep screws and fasteners organized.
• Handle the lamp and lens carefully to avoid damage; do not force-fit.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This infinite switch is the control that regulates heat for a range's surface top burner, letting you vary burner temperature smoothly for cooking. It replaces a worn or failed control to restore adjustable burner heat. What it does:

• Controls the top burner's heat level by cycling power to the surface element
• Restores adjustable temperature when a burner won't change heat settings
• Stops erratic cycling or constant-on surface caused by a failed switch
• Helps eliminate no-heat or intermittent-heat symptoms at the affected burner

• Disconnect power to the range before servicing to avoid electrical shock
• Remove the cooktop or control panel to access the switch
• Take care when handling glass cooktops, trim, and wiring harnesses to avoid damage

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

This push button is a direct-fit replacement control panel button that restores reliable tactile input for appliance functions. Replaces a worn, broken, or sticky button so you can select settings and start cycles with confidence. What it does:

• Acts as the tactile switch you press on the control panel to select functions or start cycles
• Restores unresponsive, cracked, or stuck buttons that prevent proper control operation
• Helps eliminate intermittent or no-response symptoms caused by damaged button surfaces or housings
• Matches OEM fit and form for straightforward replacement on compatible units

• Disconnect power (unplug or shut off breaker) before attempting service
• Access may require removal of the control panel or bezel—use appropriate hand tools
• Handle the button and surrounding plastic carefully to avoid cracking clips or tabs

This push button is a replacement control-panel button that restores proper user input and tactile feedback for your appliance's front controls. It gives a secure, responsive press so cycles and functions register correctly. What it does:

• Acts as the user-facing actuator for a control switch on the appliance control panel
• Helps restore missing, stuck, or non-responsive button presses
• Common symptom: buttons feel loose, don't click, or fail to activate selected cycles
• Works with the corresponding control switch assembly to transmit user input

• One replacement push button

• Disconnect power to the appliance before servicing to avoid shock or damage
• Often snaps into the control panel; may require removal of the panel or bezel
• Handle panel edges carefully to avoid damage; use a trim tool if needed
• If the underlying switch is damaged, the switch assembly may also need replacement

This electronic control board replaces the appliance's main control module to restore proper operation of timed cycles, displays and user commands. It provides the control logic that manages the unit's functions and user interface. What it does:

• Manages and sequences appliance functions such as cycle selection, timing and accessory control
• Powers and communicates with the display and touch/selector controls
• Interprets user inputs and triggers valves, motors and other components
• Faulty boards can cause unresponsive controls, incorrect cycles, intermittent operation, or display error codes

• Disconnect power to the appliance before starting any repair to avoid electrical shock
• Handle the board by the edges and avoid static discharge—use an anti-static wrist strap if available
• Verify connector orientation and secure all wiring; do not force connectors