Parts for Maytag MET8800FZ01: Cooktop Parts

This replacement cooktop top panel restores the appliance's finished cooking surface and protects the internal cooktop components. It provides a stable, clean area for burners and cookware, helping maintain safe, reliable operation. What it does

• Covers and protects the cooktop's internal components from spills, debris and heat.
• Provides the finished surface that supports cookware and allows burners/elements to seat correctly.
• Replaces cracked, chipped or heavily scratched tops that can affect cleaning and safety.
• Helps prevent spills from reaching internal parts that could cause damage or odors.

• Disconnect power to the appliance before starting work and verify the unit is cool.
• The panel is fragile—handle carefully and use appropriate protective gloves.
• Retain and reuse any OEM screws, brackets or gaskets unless replacements are specified.
• Follow the manufacturer's service instructions for proper alignment and testing after installation.

This surface heating element replaces a worn or broken top burner on compatible electric ranges, restoring even cooking and reliable heat control. Designed as a direct-fit heating element for the stove's cooktop surface. What it does:

• Heats cookware using the range's surface burner; supports high and low heat settings via the dual 1800W/800W element
• Replaces cracked, non-heating, or intermittently heating burners
• Restores consistent heat for boiling, simmering, and fry tasks
• Works with the range's existing terminal block and receptacle for a direct swap

• Disconnect power to the appliance at the breaker before installing to avoid shock hazard
• Install into the cooktop burner receptacle and secure per manufacturer instructions; ensure terminals are fully seated
• Use basic hand tools; inspect wiring and terminal block for damage and replace if corroded

This surface heating element restores dependable heat to an electric range or cooktop's top burner. Replacing a failed element helps the burner heat evenly and respond correctly to temperature settings for everyday cooking.

• Supplies controlled heat to the selected surface burner during cooking
• Common symptoms: no heat, intermittent heating, only part of the element glows, or visible damage such as hot spots or breaks
• Often tests open for continuity when failed
• Inspect the element receptacle/terminal block and wiring for heat damage during replacement

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Handle the element carefully; avoid bending terminals or touching heating surfaces with bare hands
• Transfer any brackets/insulators from the original element if present, and route wiring exactly as original
• Ensure a secure fit and connections before restoring power and testing

Replace a failed surface heating element to restore reliable, even heat on your electric cooktop or range. This 3200-watt element helps get that cooking zone working properly again.

• Generates heat for the selected surface burner when turned on
• Works with the control to reach and maintain the set cooking temperature
• Useful when the old element shows visible breaks or burn marks

• Disconnect power at the breaker/fuse box and allow the cooktop to cool completely
• Access the element beneath the cooktop top panel per your model's procedure
• Label/photograph wire locations; transfer wires and any mounting hardware from the old element
• Handle the element and glass surface carefully to prevent damage

The Surface Element is an OEM part for Whirlpool stoves and cooktops. It is the heating element located on the cooktop, responsible for providing heat to pots and pans for cooking.

Common causes of a bad surface element include wear and tear from repeated use, overheating, or electrical issues. Ensuring the element is functioning correctly is crucial for efficient and safe cooking.

Symptoms of a bad surface element include:

• Element not heating up
• Inconsistent or uneven heating
• Visible damage or burning on the element
• Sparking or electrical issues when the element is turned on

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: 1200 watt - LR / RR element

This small spring applies tension to hold an element in the correct position within the appliance, helping maintain reliable contact and stable operation. Replacing a worn spring can restore proper element support and performance.

• Provides push tension to keep the element seated and secure
• Helps prevent intermittent heating due to poor element contact
• Common signs include rattling, poor element stability, or intermittent heat

• Disconnect power and allow the unit to cool before service
• Access the element mounting area; note original spring placement
• Use needle-nose pliers to remove and install the spring carefully
• Inspect adjacent clips and wiring; replace damaged parts as needed

Comes with three connectors per package.

Size: 10-24X5/16-NI