Parts for Briggs & Stratton 19H237-0132-H1: Cylinder Head, Gasket Set - Engine, Gasket Set - Valve Parts

This exhaust valve is a genuine Midwest Engine part, sold individually. This exhaust valve can be used as a replacement part for a variety of small engine outdoor appliances including lawn mowers, snowblowers, lawn tractors, and wood chippers. The purpose of an exhaust valve is to provide a channel for the burned gas to pass outside of the appliance and out into the air.The exhaust valve might have to be replaced at some point if it can no longer provide a passageway for burned gas to pass through on its way out of the appliance. If the exhaust valve has been blocked up, punctured, cracked, or warped, the component should be removed and replaced by this genuine OEM replacement part. It is a simple repair process that will take only a few minutes. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement. Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This exhaust valve is compatible with the following outdoor appliance brands: Midwest Engine, Briggs & Stratton, Toro, Cub Cadet, MTD, and Simplicity.

A keeper valve is a small piece of hardware used to help to secure a valve. It is designed for use with pieces of outdoor lawn and garden power equipment that have small engines, a lawn mower, a snowblower, and a wood chipper. It is compatible with products by brands such as Briggs & Stratton, Craftsman, Toro, Cub Cadet, Lawn Boy, MTD, and Simplicity.The keeper valve fits into a groove in the end of the valve stem to secure the valve spring, valve spring retaining washer, and valve stem together. It is only natural that, over time, the keeper valve may wear out from regular exposure to the elements, get damaged, fall out, or become lost. In any of these events, a replacement will become necessary.The replacement or repair process of the keeper valve should be straightforward, but the user replacing the part should always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location. This keeper valve is an original OEM part sourced directly from the manufacturer, Midwest Engine. It is sold individually.

This is a durable metal valve tappet that is designed for use in small motor lawn equipment. It is attached to the push rod. The valve tappet takes the rotating motion from the camshaft and turns it into a linear motion for the valves to operate correctly. In some cases, the valve tappet can become damaged or break and will need to be replaced.If there is an issue with the valve tappet, a set of pliers will be needed to make the replacement. For safety, use work gloves and make sure the spark plug wire is disconnected before starting the replacement. The crankcase breather, muffler, and other components will need to be taken off to gain access to the valve tappet to replace it.This valve tappet is a genuine OEM replacement component directly sourced from the manufacturer. It is sold as an individual replacement part. It is designed to be used on lawnmowers, snowblowers, tillers, pressure washers, leaf blowers, generators, and chipper shredders manufactured by Briggs & Stratton, Toro, Cub Cadet, Lawn-Boy, Snapper, MTD, and Simplicity.

This replacement spark plug boot is used with a range of lawn and garden machine engines. The spark plug boot is also called a coil boot and an ignition boot. It creates voltage and mounts on top of each spark plug. It connects the spark plug to the ignition coil. Over time, the spark plug boot could start to wear down. This could be due to normal wear and tear or because of an issue of a faulty boot. Regardless, it will need to be replaced. If it is not working properly, it will be difficult or even impossible to start the engine. This is a genuine OEM replacement spark plug boot that is sold individually. The boot can be used with many models of Lawn Mower, wood chipper, snowblower, and other small engines. Compatible brands include Briggs & Stratton, Craftsman, Toro, Cub Cadet, Lawn-Boy, MTD, and Simplicity. Buyers should always ensure they are choosing the correct spark plug boot for their make and model.

This replacement valve seal is a genuine OEM part for a lawn tractor or mower. The valve stem is a type of valve that transfers oil into the cylinder and then immediately reseals due to the pressure in the chamber. However, if the seal is damaged, it will not close and oil will leak into the cylinder. If this happens, the cylinder head may become overly lubricated and not run well. This seal helps prevent that from happening. It fastens to the intake valve and valve stem keeper. Seals will naturally wear out over time due to stress and exposure to corrosive oxidizing agents in an engine. When this happens, the valve will leak oil. To test if the valve seal is compromised, look for whitish-grey smoke that indicates burning oil and also measure to see how much oil the engine is consuming. If the seal is breached, use a screwdriver and socket wrench set to change out the part. This top of the line replacement valve seal is compatible with Briggs & Stratton, Toro, and Lawn Boy lawn tractors. It is sourced from the original manufacturer and ships individually.

This is the rocker cover gasket, which seals the cylinder head on small engines so that the engine doesn’t develop leaks. Periodically, a gasket may deteriorate with heavy use. To maintain good engine performance, the rocker cover gasket needs to be replaced with an OEM certified replacement. This type of gasket is most often found on lawn tractors. Replacing the original gasket with the new one is a simple and straightforward process. There are four bolts holding the valve cover in place. Simply remove them and the old gasket, which will likely have to be scraped to get it completely off the cylinder head. Place the new gasket exactly over the metal frame of the cylinder head—it should fit perfectly. Hold it in place with a small amount of RTV, a silicon sealer that is impermeable to oil and gasoline. Replace and tighten the four valve cover bolts. This part is made by Genuine Midwest Engine. This part is used in Briggs & Stratton engines and also used by Toro and Vanguard. This is an OEM part. It's also sold individually.

This is a push rod designed to work in a lawnmower engine. Push rods serve a vital purpose in internal combustion engines. When combustion occurs, it creates not just heat and energy, but also exhaust gases. The push rod helps vent those gases so they don't choke the engine out. The push rod attaches to the camshaft, and, as the shaft turns, the rod opens the exhaust valve. Push rods are subject to high temperatures, as well as wear and tear. They can also be damaged if the engine stops unexpectedly. Bent or otherwise damaged push rods can compromise engine performance, reduce power, or even result in engine failure and cause damage to other parts. Replacing the push rod will require the disassembly of the entire engine. Replacing the tappet valve will require removing the head, as well. This is an OEM part manufactured to exacting specifications and designed to work with Briggs & Stratton engines installed on over 150 different machines. It includes a single push rod and a tappet valve.