Martin M Cape Coral , FL October 18, 2014 High voltage control board The touchpad on my Maytag refrigerator was going nuts flashing and buzzing. Also, the ice dispenser door was opening and closing at will. I researched the issue on the internet and on the AppliancePartsPro.com website and others were describing the same issue. The recommended replacement part by AppliancePartsPro.com tech was the High Voltage Control Board. I ordered the part from them and is arrived sooner than promised which was great. It took me less than 10 minutes to replace the board in the back of the unit. After following the reprograming instructions that were included, the refrigerator was back to normal. The ice maker is working and the freezer is also working properly. This is the second time I order refrigerator parts from AppliancePartsPro.com, The first time was for the touchpad in the front. Both times I was successful making the repairs with the assistance of their techs. I am completely satisfied with AppliancePartsPro.com and will continue to order parts from them, although if I never have to repair my other appliances that would be good too! Thank you AppliancePartsPro.com. Read More... 55 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers
Maria J Charlottesville , VA July 27, 2014 Display was flashing water and ice dispenser did not work ice door flapping I replaced the control board on the back of the refrigerator. Simple task, easy-to-follow instructions came with the replacement control board. I am very happy with this product, and with the service of AppliancePartsPros.com. Read More... 44 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers, Pliers, Screwdrivers
Rz57615-richard Z Sumas , WA December 15, 2014 Appliance: Model MF12568AES (MAYTAG) Front display was flashing the ice/water door was flipping back and forth making a poping sound also the fridge was not cold I replaced the HIGH VOLTAGE circuit board that is located in the back of the fridge Read More... 10 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers
Mark P Mount Vernon , WA May 12, 2020 Flashing lights on the control panel of the refrigerator and flapping ice door. Installed the new "High Voltage Board" (took about t 10 minutes) and programmed the new board to my refrigerator's code. Very easy and it no more flashing lights or flapping ice-maker door. Read More... 5 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers
Curtis S Chillicothe , OH May 11, 2016 The temperature led readouts were blinking the ice chute cover was flapping up and down and the water and ice dispensers did not work Replaced the HV main control board. Used pliers to remove the screws holding the cover plate on the back of the fridge. Removed the plastic cover plate, then used a screwdriver to pry the plastic clips that hold the board in place. Once replaced, reprogrammed the new board following the included directions. Read More... 5 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Pliers, Screwdrivers
Audrey S Austin , TX September 25, 2018 Appliance: Model MAYTAGE FRIDGE The ice port would not stop flapping and frig and freezer were not cooling DIY by purchasing a new control panel. Easy!! Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Wrench Set
Timothy P Marietta , GA August 08, 2016 Appliance: Maytag Refrigerator MFI2568AES12 Front panel flashing ice maker continuously flapping After a few google searches and with the help of this site, I found that I just needed to replace the main control board. I originally called Maytag directly, but it would be 3 or 4 days to get someone out there to look at it and cost me $100 just for them to walk in my door. There is a video on youtube where they walk you through the removal and installation - the hardest part for me was positioning the refrigerator in a way where I could get behind it. Removed the back panel, unclipped the control board and plugged in the new one. About 20 minutes total from start to finish. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Socket Set
Rich J Langhorne , PA June 12, 2016 Flashing lights water/ice dispencer flapper constanly flapping fridge temp not working Replaced with new HV Control Board. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers
Gary W Washoe Valley , NV June 05, 2015 Appliance: Maytag Refrigerator MFI2067AES10 Ice door flapping lights flashing then went out stopped cooling properly Reading similar issues from other people, it was pretty clear the solution was the High Voltage Control Board. It was easy to replace and only took about 15 minutes. The access panel is in back of the refrigerator. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers, Screwdrivers
Ronald R Warren , MI November 12, 2022 Appliance: Maytag Refrigerator MFI2067AES10 My refrigerator was not dispensing water and getting warm inside 55 deg f. I ordered the Control Board for my Maytag refrigerator on Sunday 11/6/22. It came on Wednesday 11/9/22. I unplugged the unit and remove the metal and plastic covers on the back. Unplugged (4) connectors, and popped out the old board. Installed the new Control Board and covers. Plugged in the refrigerator and programmed the code (0202) according to the instructions. MY REFRIGERATOR IS WORKING GREAT! Thanks for the fast service. Ron Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers