Parts for Whirlpool WFE775H0HB2: Door Parts

This trim vent is the molded outlet trim that finishes the cabinet opening and helps direct cold air from the refrigerator/freezer where needed. It restores a clean appearance and proper airflow at the vent opening. What it does:

• Covers and finishes the vent opening at the cabinet for a factory look
• Directs airflow from the evaporator area into the fresh-food or freezer compartment
• Replaces cracked, broken, or warped vent trim that lets cold air escape or looks damaged
• Helps prevent large debris from entering the vent opening

• Disconnect power to the appliance before beginning any work.
• Typically a snap-in or screw-retained replacement; remove any retainers and pull the old trim straight out.
• Align the new trim and press or fasten until it seats securely; do not force or bend the piece.
• If screws or clips are reused, ensure they are in good condition and tightened securely.

The Screw is an OEM replacement part for Whirlpool ranges. It is responsible for securing various parts of your range together. This screw ensures a tight and secure fit for different components of your range, such as the cooktop, control panel, or oven door. It provides stability and prevents any loose parts.

A bad range screw can occur due to wear and tear, accidental damage, or misplacement. If you notice symptoms such as loose or unstable parts, rattling noises, or difficulty in opening or closing the oven door, it may indicate a faulty or missing range screw.

Symptoms of a bad range screw include:

• Loose or unstable parts
• Rattling noises during operation
• Damaged or missing screw

Repair your range by replacing the faulty or missing range screw with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement door handle restores a secure, comfortable grip for opening and closing your appliance door while repairing cosmetic damage. It matches OEM fit and finish to help maintain proper door operation and appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces a cracked, broken, loose, or worn handle to restore usability
• Helps keep the door aligned and easier to operate when fastened correctly
• Improves the appliance's appearance by replacing damaged or discolored hardware

• Requires basic hand tools; support the door while removing and installing the handle
• Follow the appliance manufacturer's instructions for fastener locations and torque
• Do not overtighten screws — snug is sufficient to avoid cracking the handle
• Unplug the appliance or turn off power if accessing components near electrical parts;

This replacement refrigerator door handle restores a secure grip and normal door operation after a worn, cracked, or broken handle. Durable, service-ready design helps keep the door easy to open and close. What it does:

• Replaces a damaged or broken refrigerator door handle so the door can be opened and closed safely
• Provides a solid gripping surface for everyday use
• Helps prevent further cabinet or door edge damage caused by makeshift grips
• Common symptom: handle cracked, loose, or separated from the door

• Use the model's service manual for correct fastener locations and procedures
• Typically installs with screws or clips; have basic hand tools ready
• Avoid overtightening fasteners to prevent damage to the handle or door
• If the door has electrical components (ice/water dispensers), unplug the appliance before starting work

This inner oven door liner replaces the damaged or warped inner panel that supports the oven door glass and helps contain heat inside the oven cavity. It restores a solid mounting surface for door glass and internal components. What it does:

• Provides the inner structural panel for the oven door and supports the door glass and insulation.
• Helps maintain proper oven heat containment to support uniform cooking.
• Prevents direct exposure of insulation and internal parts to oven cavity heat and food debris.
• Addresses symptoms like visible cracks, warping, or detached glass mounting points on the inside of the door.

• Disconnect power before starting any repair and follow manufacturer's safety instructions.
• Remove the oven door per the appliance manual to access and replace the inner liner; handle glass and sharp edges carefully.
• Keep all original screws and mounting clips; confirm screw locations during disassembly to ensure proper reassembly.
• If the door has multiple glass panels or seals, verify placement during reassembly—do not force parts into position.

This factory fastener secures appliance panels, brackets, and internal components. Replacing a missing, stripped, or corroded screw restores proper fit and stability, helping reduce vibration, rattling, and wear during everyday operation.

• Secures covers, brackets, and assemblies to the cabinet or frame
• Restores alignment to reduce gaps, looseness, and vibration
• Replaces lost, damaged, corroded, or stripped hardware
• Matches the original fastener for correct fit and retention

• Disconnect power and shut off water or gas before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent thread or plastic damage
• Inspect receiving threads or clips; repair/replace if stripped or broken

This inner door glass is the heat-resistant panel mounted on the inside of the oven door. It restores a clear, secure barrier to help retain heat and visibility when the original glass is cracked, shattered, or stained.

• Forms the inner pane of the oven door to contain heat and allow viewing of food
• Damage can cause heat loss, longer preheat/cook times, and unsafe sharp edges
• Cracked, shattered, or missing glass should be replaced before using the appliance
• Cloudy or permanently stained glass reduces visibility into the oven

• Disconnect power at the breaker and allow the oven to cool completely
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Support or remove the door and work face-down on a padded surface
• Transfer any brackets/clips/insulation as configured; do not overtighten fasteners against the glass

This mounting bracket secures internal or external appliance components to the cabinet, restoring proper alignment and preventing vibration. It's a small but critical metal support used where fasteners attach panels or assemblies. What it does:

• Provides a secure attachment point for panels, controls, or assemblies
• Prevents loosening, rattling, and misalignment caused by broken or missing supports
• Restores proper fit and function when original bracket is bent, cracked, or missing
• Works as a direct replacement using existing fasteners and mounting holes

• Disconnect power (and gas if applicable) before beginning any repair
• Installation typically requires basic hand tools (screwdriver, nut driver, or socket)
• Retain or reuse original screws; verify bracket orientation before tightening
• If metal edges are sharp, use care and protective gloves to avoid cuts

The Door Hinge is an OEM part for Whirlpool ovens. This hinge is crucial for supporting the oven door, allowing it to open and close smoothly. It ensures the door remains securely in place during cooking and baking.

Over time, oven door hinges can wear out or become damaged due to frequent use and exposure to high temperatures. Common causes of a bad hinge include metal fatigue, rust or corrosion, and accidental damage from slamming the oven door.

Symptoms of a bad hinge include:

• Difficulty opening or closing the oven door
• The oven door not staying securely closed
• A misaligned or sagging oven door
• Noises or squeaks when the door is operated

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This outer oven door glass panel restores the door's exterior and replaces damaged or cracked outer glass for a clean, safe appearance. Fits the matching door assembly and helps maintain the oven's finished look. What it does:

• Replaces cracked, chipped, scratched or shattered outer door glass that affects appearance or safety
• Provides the oven's finished exterior surface and protects inner layers of the door
• Secures into the door assembly to keep internal components covered and stable
• Helps maintain proper door closure when installed correctly

• Wear cut-resistant gloves and eye protection; glass edges may be sharp
• Door removal is typically required to access and replace the outer glass
• Handle glass carefully and avoid dropping or flexing it; do not overtighten any fasteners
• If the inner door glass, clips, or seals are damaged, replace them as needed.

This door trim is the front-facing decorative bezel that restores the finish and edge protection to your appliance door. It replaces a worn, cracked, or damaged trim to improve appearance and help seal the door edge. What it does

• Replaces damaged or cracked door bezel to restore appearance
• Covers and protects the door edge from impacts and wear
• Helps maintain a clean seal line by securing the door edge trim
• Common symptom: visible cracks, chips, or loose trim along the door perimeter

• One door trim piece as shown

• Disconnect power to the appliance before beginning any service
• Use appropriate tools and keep fasteners for reassembly; handle trim carefully to avoid damage

This outer door trim restores the finished appearance of an appliance door and covers the edge gap between the door panel and console for a clean, factory look. It helps protect the door edge from everyday wear. What it does:

• Covers and finishes the outer edge of the appliance door for a seamless appearance
• Helps prevent dirt and moisture from collecting at the door edge
• Restores cosmetic damage like scratches, dings or missing trim pieces
• Useful when replacing a cracked, warped or broken door trim piece

• High-level replacement only; remove and reinstall the outer door panel to access the trim
• Use appropriate screwdrivers and keep fasteners organized for reassembly
• Disconnect power (or gas) and follow manufacturer's safety steps before beginning service
• If trim is clipped in, carefully release retaining clips to avoid breaking adjacent parts

This screw-and-washer fastener is a factory-size 8-18 x 5/16 hardware piece used to secure appliance panels and components. Replace stripped, rusty, or missing hardware to restore a tight, rattle-free fit and proper alignment. What it does:

• Fastens sheet-metal panels, brackets, and small components in the appliance cabinet
• Replaces lost, stripped, or corroded screws to maintain secure mounting
• Helps reduce vibration, buzzing, or rattling from loose parts
• Useful when the original hardware is missing or no longer holds securely

• Includes 1 screw-and-washer fastener (8-18 x 5/16)

• Disconnect power; shut off gas and water supplies if applicable
• Match the fastener to the original location; sizes can vary by application
• Start threads by hand to avoid cross-threading; use an appropriately sized driver
• Tighten snugly without overtightening to prevent stripping sheet metal

The Range Bracket-Glass is an OEM part for Whirlpool ranges. It is designed to support and secure the glass surface or cooktop in place, ensuring stability during operation. This bracket is essential for maintaining the proper alignment and positioning of the glass panel.

Causes of a damaged bracket can include repeated exposure to heat and stress during cooking, accidental impacts, or improper installation. Over time, the material may weaken, crack, or warp, compromising its ability to hold the glass securely.

Symptoms of a bad bracket include:

• Loose or wobbly glass cooktop
• Visible cracks or damage to the bracket
• Gaps between the glass and the frame
• Difficulty securing the glass properly during reassembly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Range Bracket-Glass (White) is an OEM part for Whirlpool ranges. It is designed to support and secure the glass surface or cooktop in place, ensuring stability during operation. This bracket is essential for maintaining the proper alignment and positioning of the glass panel.

Causes of a damaged bracket can include repeated exposure to heat and stress during cooking, accidental impacts, or improper installation. Over time, the material may weaken, crack, or warp, compromising its ability to hold the glass securely.

Symptoms of a bad bracket include:

• Loose or wobbly glass cooktop
• Visible cracks or damage to the bracket
• Gaps between the glass and the frame
• Difficulty securing the glass properly during reassembly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Screw is an OEM part for Whirlpool ranges. This screw is used to secure various components within the range, ensuring that parts such as panels, control boards, or burners are firmly attached and remain stable during operation.  

Causes of a bad range screw can include regular wear and tear, over-tightening, or exposure to high heat.  

Symptoms of a bad range screw include:

• Loose or unstable components within the range
• Difficulty in securing parts during maintenance or repair
• Visible damage or wear on the screw
• Parts becoming misaligned or rattling during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This support bracket secures internal components to the appliance chassis, restoring proper alignment and stability for attached parts. It's a simple replacement that helps stop rattling and prevents components from shifting during use. What it does:

• Provides a secure mounting point to hold panels, assemblies or components in place
• Helps eliminate vibration or rattling caused by a loose or broken bracket
• Restores proper alignment so connected parts operate correctly
• Prevents further wear or damage from loose components

• Disconnect power to the appliance before starting any repair
• Basic hand tools (screwdriver, nut driver) are typically required
• Keep original fasteners and note their location for reassembly; replace damaged hardware as needed

This replacement screw with a 10-16 thread secures panels, brackets, and other components in your appliance. Restoring the correct hardware keeps parts tight and aligned, reducing vibration and preventing loosening over time.

• Secures sheet-metal panels, brackets, and assemblies
• Replaces missing, stripped, or corroded fasteners
• Helps eliminate rattling or vibration from loose hardware
• Maintains proper alignment for reliable performance

• Disconnect power; turn off the water supply before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten into sheet metal or plastic
• Reinstall in the original location and orientation

This spacer positions and aligns components inside the appliance to ensure correct fit and reduce rubbing or stress on adjacent parts. Replaces a worn or missing spacer to restore proper part spacing and stable operation. What it does

• Keeps panels, motor mounts, or assemblies correctly spaced to prevent rubbing and misalignment
• Helps reduce vibration and noise caused by loose or shifted components
• Maintains proper clearance for moving parts to avoid premature wear
• Common symptom: uneven fit, rattling, or unusual contact between parts

• One spacer

• Disconnect power (and water if applicable) before starting any repair
• Compare the replacement spacer to the original for correct size and orientation before installing
• Retain and reuse original fasteners unless new hardware is specified elsewhere

This oven cavity insulation panel helps reduce heat loss and improves temperature stability inside the oven for more even cooking. It replaces worn or damaged insulation that can allow heat to escape or make the exterior hotter than normal. What it does:

• Provides thermal barrier between the oven cavity and outer cabinet to help maintain internal temperature
• Reduces heat transfer that can cause the exterior surfaces to become unusually hot
• Helps prevent excessive heat loss that can affect cooking performance and energy use
• Fits behind the oven liner where original insulation is mounted

• One oven cavity insulation panel

• Disconnect power (and gas, if applicable) before starting any repair
• Handle insulation with gloves; avoid compressing or tearing the material
• Follow the appliance service manual for proper placement and secure mounting

Color: Grey