Parts for Crosley CFD28SDQSA: Fresh Food Doors Parts

The Fresh Food Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the refrigerator door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper refrigerator conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the refrigerator
• Difficulty keeping the refrigerator door fully closed
• Warm air entering the refrigerator, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

NOTE: GASKET NOW GRAY, NOT WHITE

The Door Stop is an essential OEM replacement part for Frigidaire bottom-mount refrigerators. It functions to securely hold the refrigerator door fully open during loading and unloading of food items. 

Causes of a faulty door stop include cracking or warping due to years of resisting door closure force during access. Friction might also wear down moving lever components over time.

Symptoms of a bad door stop are:

• Refrigerator door unable to safely prop fully open  
• Door slowly closing partially while items are retrieved
• Visible wear marks or loss of lubrication where door pivots

This authentic OEM replacement is compatible for Frigidaire, Electrolux and Kenmore models. 

This door stop is the replacement part that limits door travel and cushions the refrigerator door for smoother closing and reduced impact. It helps restore proper door alignment and prevents the door from hitting the cabinet. What it does:

• Stops or limits door travel to prevent over-opening and cabinet damage
• Cushions door movement to reduce slamming and wear on hinges
• Helps maintain correct door alignment so the seal engages properly
• Commonly used when the door hangs unevenly, slams, or won't stay aligned

• Disconnect power or unplug the appliance if accessing electrical components is required.
• Support the door or remove it before replacing hinge or stop hardware.
• Basic hand tools usually required; keep track of small screws and clips.
• Test door operation and alignment after installation; adjust as needed.

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

The Door bin is an OEM replacement part for Frigidaire refrigerators. It is a built-in storage compartment designed to hold commonly used items like eggs, butter, or condiments. The door bin provides convenient access to the refrigerator door.  

Causes of a bad door bin can include cracked or broken plastic, damaged sliding tracks that prevent smooth opening and closing, or broken mounting tabs that cause it to become loose or detached from the refrigerator door.

Symptoms of a bad door bin include:

• Items falling out of the bin easily  
• The bin not closing or securing properly
• Difficulty opening and closing the bin
• Noise or vibration from a loose or damaged bin

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models. 

The Door Bin is an OEM replacement part for Frigidaire refrigerators. The door bin is responsible for organizing smaller items and optimizing interior space utilization. It measures approximately 5" depth x 12 1/2" width x 3" height.

Causes of a bad door bin can include damage such as cracks or breaks in the plastic, broken adjustable shelves, or issues with the mounting brackets that secure it inside the refrigerator door. 

Symptoms of a bad door bin include:

• Items falling out of the bin due to structural integrity issues
• Difficulty accessing storage areas due to broken shelving  
• The bin not sitting securely inside the door

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This Door Bin is an OEM part for Frigidaire refrigerators. This bin is located on the interior side of the refrigerator door, providing convenient storage space for items such as bottles, jars, and condiments. It helps keep the refrigerator organized and maximizes available storage.

Causes of a bad door bin can include wear and tear, accidental damage, or improper handling.

Symptoms of a bad door bin may include:

• Cracks or breakage in the bin
• Difficulty in securely holding items
• Limited storage capacity due to a damaged or missing bin

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Hinge Pin is an OEM part for Frigidaire refrigerators. It is responsible for supporting the mullion or flapper, which is the vertical strip that divides the refrigerator doors. It provides smooth movement and proper alignment of the mullion, allowing it to pivot easily for access to both compartments while maintaining an airtight seal when closed.

Causes of a bad hinge pin can include wear and tear over time, accidental damage, or improper handling. A damaged or worn-out hinge pin may result in difficulties in opening or closing the mullion.

Symptoms of a bad Hinge Pin include:

• Difficulty in opening or closing the doors
• Excessive play or wobbling of the mullion
• Failure to maintain a proper seal between door
• Unusual noises during use

This OEM Frigidaire part can also be used on select Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore models.

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

This refrigerator door mullion is the flip-up divider attached to the fresh food door that covers the gap between doors. It helps the doors seal properly, limiting air leaks and moisture at the center seam for consistent cooling performance. What it does and common symptoms:

• Flips into place as the door closes to create the center seal between doors
• Helps maintain interior temperature and reduce condensation at the door seam
• Replace if cracked, warped, loose, or not springing/aligning with the door gasket
• Symptoms can include doors not latching cleanly, visible damage, or moisture along the middle

• One door mullion assembly

• Unplug the refrigerator before servicing
• Remove door bins if needed; support the mullion and remove the mounting screws
• Lift the mullion off its pivots, position the new part, and reuse existing hardware to secure it
• Verify smooth flip action and a tight seal before restoring power

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

The Flipper Mullion is an OEM part for Frigidaire refrigerators. As the panel separating the fresh food and freezer compartments, it flips up for access while also providing an insulating barrier. 

Causes can range from normal wear and tear on hinge mechanisms to cracks or breaks from accidental impacts over years of use.

Symptoms of a bad flipper mullion include:

• Difficulty or resistance when trying to open
• Improper sealing between compartments, leading to air and temperature leaks
• Visible wear, cracks or damage to the component over time

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Flapper Door Center Hinge is an OEM part for Frigidaire refrigerators. This hinge is essential for the proper operation of the flapper door, which helps seal the gap between the refrigerator doors when they are closed, ensuring efficient cooling and energy use.

Over time, the center hinge can wear out or become damaged due to regular opening and closing of the refrigerator doors. Accumulation of dirt, dust, or debris, as well as physical impact, can also contribute to hinge failure.

Symptoms of a bad flapper door center hinge include:

• The flapper door not closing properly
• Gaps between the refrigerator doors
• Increased energy consumption due to cold air escaping
• The refrigerator doors not aligning correctly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Right Door Closer is an OEM part for Frigidaire refrigerators. It is responsible for ensuring that the refrigerator door closes securely and maintains a proper seal, keeping the cold air inside and your food fresh.

A bad right door closer can be caused by wear and tear, damage, or misalignment. When the closer becomes faulty, it can result in issues such as a loose or sagging door, difficulty in closing the door properly, or a compromised seal that leads to temperature fluctuations.

Symptoms of a bad right door closer include:

• Door not closing or sealing properly
• Condensation or frost buildup inside the refrigerator
• Noisy or squeaking door operation

Replace your faulty right door closer with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This left-hand door closer replaces the refrigerator/freezer door closer that helps the door swing closed smoothly and stay aligned for a proper seal. Restores reliable closing and reduces door sag or misalignment. What it does:

• Guides and supports the left-side door as it closes to prevent slamming and ensure proper latch engagement
• Helps maintain an even seal to preserve internal temperature and reduce energy loss
• Reduces door sag, rubbing, or uneven gaps caused by worn or broken closers
• Works with the existing hinge/door hardware to control door motion

• High-level replacement — remove the door trim/inner panel to access the closer if required
• Keep screws and brackets organized; verify orientation for left-hand side before fastening
• Disconnect power to the appliance or follow manufacturer's safety guidance when working near electrical components

This small rubber door bumper cushions and aligns the refrigerator door to reduce slamming and wear. It restores smooth closing and helps keep the door sealed for proper cooling. What it does:

• Absorbs impact when the door closes to prevent hard bangs and protect cabinet surfaces
• Keeps the door properly spaced to help maintain a consistent seal
• Reduces rattling or vibration caused by loose or worn bumpers
• Simple, low-profile part used at door contact points or stops

• One replacement bumper

• Power is off if working near electrical components; follow appliance safety precautions
• Remove the old bumper by pulling it from its mounting hole; press the new bumper firmly into place until seated
• Use gloves to protect your hands; avoid using excessive force or tools that could damage trim
• Replace with the exact OEM part number for proper fit and function

This 3/32" screwdriver is the service tool used to access and adjust small screws on appliances, making routine panel and control adjustments easier and more precise. Handy for basic repairs and maintenance. What it does:

• Fits 3/32" slotted screws commonly found on control panels, trim, and small fasteners
• Allows removal and installation of small service screws for access to internal components
• Helps correct loose screws that can cause rattling or misaligned panels
• Provides better fit than oversized drivers to reduce screw head damage

• Always disconnect power to the appliance before performing service or repairs
• Use the correct 3/32" blade size to avoid stripping screw heads
• Apply steady pressure and avoid excessive torque; use hand force only unless otherwise specified

This genuine replacement screw secures appliance components and restores proper fit and stability. Use it to replace a missing or damaged fastener and stop panels, trim, or parts from shifting or rattling during normal use. What it does:

• Fastens and holds panels, brackets, or small components in place
• Restores secure attachment when an original screw is missing, damaged, or stripped
• Helps eliminate vibration, rattling, or loose-fitting parts
• Matches the OEM fit and function for reliable reassembly

• Use correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and remove food or contents from appliance areas as needed before servicing
• If fastener threads are damaged, replace with the exact OEM screw rather than forcing installation

This Mullion harness routes electrical connections through the refrigerator door mullion so lights, sensors and control/LED assemblies communicate with the main cabinet wiring. It restores reliable power and signal routing in the door center strip. What it does:

• Carries power and signal between the door/mullion components and the main harness
• Restores non-functioning mullion lights, LEDs or control communication caused by a damaged harness
• Prevents intermittent connections from frayed or broken mullion wiring
• Used when visible wire damage or connector failure is found in the mullion area

• One (1) mullion harness as pictured

• Disconnect power to the appliance before starting work to avoid shock or injury
• Remove the mullion/door trim and any gaskets per service instructions to access the harness
• Inspect connectors and wire routing; replace any clips or retainers to prevent pinching

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required