Parts for Ge PFSS6PKXESS: 02 - Fresh Food Doors Parts

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

A self-tapping screw used to fasten appliance panels and components where a threaded hole is formed as the screw is driven. Provides a secure hold for trim, brackets, and light assemblies during repairs. What it does:

• Cuts its own mating thread in sheet metal or thin plastic to secure panels and brackets
• Helps hold trim, access panels, or internal components in place
• Commonly used where a tapped hole is not present or repair requires a replacement fastener
• Can prevent loose parts and rattles caused by missing or damaged screws

• Unplug the appliance before servicing to avoid electrical or mechanical hazards
• Use the correct screwdriver or bit to avoid stripping the screw head
• Start the screw straight and apply steady pressure; do not overtighten to avoid cracking plastic or stripping metal
• Replace only with the exact part number to ensure proper fit and function

This is the door gasket for the refrigerator (fresh food) compartment. It creates an airtight seal around the door to keep cold air in, reduce moisture, and help maintain proper temperatures.

• Seals the fresh food door perimeter to prevent air leaks
• Helps reduce condensation, frost, and temperature swings
• May help if the door won't seal, the gasket is torn, or food is warming
• A worn or deformed gasket can increase run time and energy use

• Unplug the appliance before service
• Warm the new gasket (hair dryer on low or warm water) to relax folds
• Transfer any retainers if applicable; seat the gasket fully into the channel
• Check door alignment and adjust hinges if needed for proper seal

Color: white. Measures about 15 inches wide by 4-1/2 inches high by 7-1/2 inches deep.

The French Door Spring Pin is an OEM part for GE refrigerators. It plays a crucial role in the proper functioning of the refrigerator's French doors by ensuring they close securely and smoothly. This spring pin helps maintain the alignment and tension of the doors, contributing to the overall efficiency and usability of the appliance.

You should replace this French door spring pin if it becomes damaged or fails. Causes of a bad spring pin can include wear and tear over time, accidental damage, or corrosion due to exposure to moisture.

Symptoms of a bad French door spring pin include:

• Difficulty in closing the refrigerator doors
• Doors not staying securely closed
• Misalignment of the French doors
• Unusual noises when opening or closing the doors

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a French spring, or French divider door spring. It is used in refrigerators. This part allows the doors to open and close. It is located in the door of the fridge. A new French divider door spring may be needed if the door is stuck or is coming off of its hinges. This repair requires only a standard household toolkit. To replace the spring simply remove the old one and replace the part with a new, working piece. Be sure not to bend the spring while installing it as it will not fit in as the replacement part. This is a genuine OEM part. It is sourced directly from the manufacturer and is sold individually. This specific French Divider Door Spring is compatible with appliances made from General Electric.

This ice chute cap gasket seals the ice chute cap to help keep ice contained and reduce air or moisture intrusion in the dispenser area. It restores a tight, flexible seal for proper ice dispensing and storage. What it does:

• Seals around the ice chute cap to help prevent ice spills and migration
• Limits warm air and moisture from entering the ice compartment
• Helps reduce ice clumping and sticking by maintaining a stable chute seal
• Restores proper fit where a worn or torn gasket allows gaps

• Disconnect power to the appliance before inspecting or replacing the gasket
• Remove the chute cap carefully, clean mating surfaces, and press new gasket fully into place for an even seal
• Inspect surrounding trim for damage and handle the gasket gently to avoid tears
• If adhesive or fasteners are present on your model, use only OEM-recommended methods

This dispenser cover assembly replaces a cracked or damaged dispenser housing cover to restore a clean appearance and help the dispenser direct ice and water properly. Molded plastic protects internal components and maintains dispenser alignment. What it does:

• Covers and protects the dispenser opening and internal components from dirt, moisture, and impact.
• Helps guide ice and water to reduce jams, misfeeds, and drips at the dispenser opening.
• Restores appearance when the original cover is cracked, split, or cosmetically damaged.
• Seats into the dispenser housing using factory clips and mounts to maintain proper alignment.

• Disconnect power and shut off the water supply before servicing to prevent shock and leaks.
• Remove dispenser trim or inner door panel to access the cover; support the door/trim while working.
• Handle plastic clips and tabs carefully—damaged clips may require replacement.
• After installation, restore power/water and test the dispenser for proper function and leaks.

This is an ice chute and funnel assembly for refrigerators with ice dispensers on their doors. The chute opens upon the user's command input and releases ice into a glass or other container placed underneath it. With use, because of misuse, or as a result of accidental damage, part or all of the ice chute door and funnel may malfunction or fail entirely. When this happens, a replacement part is required to continue using the ice dispensing feature.If the ice chute no longer dispenses ice, or if it is dispensing too much or too little ice, it's a good indication that there is something wrong with this part of the appliance. It's a quick repair. It is always recommended to unplug the device before beginning the replacement. Move any food that could spoil while the repair is being completed.This refrigerator ice dispenser ice chute door and funnel assembly is a genuine OEM replacement part. It is sourced directly from the manufacturer. It is sold as an individual unit and made of durable materials. The replacement part is compatible with several models of refrigerators manufactured by General Electric, Hotpoint, and RCA.

A replacement dairy door guard that restores the small bin used to hold butter, cheese and other dairy items in the refrigerator door. Keeps small containers secure and helps organize the door storage. What it does:

• Replaces a cracked, broken or missing dairy/bin guard on the refrigerator door
• Holds small dairy items and prevents them from shifting when the door is opened
• Stabilizes door storage and helps maintain convenient access to frequently used items
• Fits into the door inner liner and snaps or screws into place depending on model

• Remove items from the door and support the door or work with it open on a stable surface
• Most installs snap into the door liner; some models may require removing a retaining screw
• Use basic hand tools if a screw is present; avoid overtightening fasteners
• Disconnect power only if required by your model's door removal procedure; follow the refrigerator manufacturer's instructions