Parts for Ge JGBS61DP2WW: Gas & Burner Parts

LP conversion kit for gas ranges. Includes burner orifices to convert your range from natural gas to LP propane. Replace missing or lost conversion parts.

Replace a cracked, stripped, or missing surface burner control knob on your gas range. Mounts on the valve stem to control flame level and settings.

Replacement fastener nut for gas ranges and cooktops. Secures panels and internal components. Needed when original nut is missing, stripped, or worn.

Phillips head mounting screw for range control knobs and switches. Replaces lost, stripped, or damaged screws. 8-32 thread size for secure installation.

Large burner injector for gas ranges and cooktops. Replaces cracked, worn, or missing injectors that control gas flow to the burner assembly.

Fixes burners that won't ignite or spark inconsistently. This wiring harness restores electrical connections to igniters and gas valves. Quick DIY fix.

Surface burner base that covers and protects the burner cavity on gas ranges. Replace if warped from heat, cracked from impact, or corroded over time.

Manifold pipe for gas ranges. Distributes gas from the valve to the burners. Replace if cracked, damaged, or leaking. Direct fit component.

If your ice maker isn't filling properly or ice cubes are misshapen, this inlet jet restores correct water flow to the dispenser and ice-making area.

Protective cover that slips over the gas valve shaft to shield valve components from spills, food debris, and moisture. Replace if cracked or missing.

This wire tie secures and organizes wiring inside the appliance to help prevent chafing and loose connections. Its 7-7/8 inch length is suited for bundling harnesses and routing cables away from heat and moving parts. What it does:

• Fastens and groups wires or small hoses to keep them neatly routed
• Helps prevent wire chafing, abrasion, and contact with sharp edges
• Reduces the chance of intermittent connections from loose wiring
• Keeps wiring away from moving components to reduce noise and wear

• Disconnect power before servicing the appliance
• Position wiring as needed, insert tie and tighten; avoid over-tightening
• Trim excess tie length flush and secure cut end away from wires
• Replace any damaged wiring insulation and verify routing before restoring power

If your gas range burner flame is uneven or won't stay lit, the orifice holder may be damaged. This bracket secures the orifice under the cooktop.

Fixes uneven flames, yellow flames, or hissing sounds from your left front burner. This orifice holder secures the gas nozzle for proper fuel delivery.

Fixes rear burner ignition issues and uneven flames. This orifice holder secures the gas orifice in position for reliable flame performance. Simple repair.

If your gas range burner won't ignite or has an uneven flame, the orifice holder may be damaged. This part secures the orifice for proper alignment.

Secures the igniter to the burner assembly in gas ranges and ovens. Replace if stripped, missing, or damaged during igniter replacement or repair.

Burner won't light or flame is weak? This gas range burner valve controls gas flow to the cooktop burner. Requires removing cooktop for access.

Fix a burner that won't adjust or turn off properly. This gas valve controls flame height from simmer to high heat. Moderate DIY difficulty.

Uneven flames or weak heat? This valve burner regulates gas flow to the burner ring. Common fix for temperature control issues on gas ranges.

Fix uneven oven heating or weak flames with this LP gas oven orifice spud. Controls propane flow to the burner for proper combustion in gas ranges.

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

If your gas oven won't ignite or gas is leaking, the valve control assembly may be faulty. Houses the gas valve, igniter, and control logic for safe fuel flow.

Fixes uneven heating or ignition failure in gas range ovens. This oven burner assembly holds ignition and valve components over lower cooking surfaces.

Oven won't heat or takes forever to reach temperature? This igniter creates the spark to ignite gas for baking. DIY-friendly repair, 20-30 minutes.

Pre-formed gas line that connects the inlet regulator to the burner manifold in gas ranges. Replace if damaged, cracked, or leaking to restore safe operation.

Secures and routes wiring in your range. Replace if loose, broken, or wiring is exposed. Verify fit with your model number before ordering.

Gas range burner won't ignite or flame is uneven? This round valve controls gas flow to your burners. A common fix for temperature control issues.