Parts for Whirlpool 7MWTW4925EW1: 05 - Gearcase, Motor And Pump Parts

This factory fastener secures appliance panels and components for a tight, rattle-free fit. Replace a missing, stripped, or corroded screw to keep assemblies aligned and performing as intended.

• Fastens panels, brackets, or assemblies in place
• Helps reduce vibration and rattling caused by loose hardware
• Maintains proper alignment of parts to prevent premature wear
• Common signs you need it: missing screw, loose panel, vibration/buzzing noises, or hardware that won't tighten

• Disconnect power; for gas or water-connected appliances, shut off supply lines before service
• Match the screw to the original; verify size, length, and thread before installation
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug only—do not overtighten, especially into plastic or thin sheet metal

The Internal Drain Hose is an OEM replacement part for Whirlpool washing machines. It routes used wash water from the tub to an external drain source. 

Causes of a faulty internal drain hose can include cracks developing from constant use or obstructions blocking effective drainage.

Symptoms of a bad internal drain hose include: 

• Water leaks inside or around the base of the washer
• Incomplete drainage of water at the end of cycles  
• Accumulation of dirty water inside the machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This replacement 7-2-1 screw secures components in compatible Whirlpool appliances, providing a dependable fastener for panels and assemblies. Use it to restore proper fitment and reduce rattling or loose parts. What it does

• Fastens trim, panels, brackets, or internal assemblies to keep parts secure
• Helps stop vibration-related noise from loose components
• Restores correct mounting where the original screw is missing or damaged
• Matches the form and fit of the OEM fastener for intended attachment points

• One replacement 7-2-1 screw

• Use the correct driver to avoid stripping the screw head
• Hand-start threads before tightening to prevent cross-threading
• Tighten until snug—do not over-tighten to avoid damaging plastic or sheet-metal parts
• Disconnect power to the appliance before accessing internal areas

This part is a genuine OEM replacement drive motor. It is intended to replace a broken or faulty motor in various washers.This motor drives the washing machine, allowing the drum to rotate and agitate when the user selects the desired settings. Over time, the motor might become worn or start to malfunction, requiring immediate replacement. Before starting the repair process, unplug the appliance from the power source and check the resistance running through the motor windings using a multimeter. If the meter measures infinite resistance, the drive motor will definitely need to be replaced. Work gloves should be worn to prevent injury.This part has been made by Whirlpool and has been sourced directly from the manufacturer. This part is made out of high-quality, durable, non-corrosive materials to ensure high quality and is sold individually. It is compatible with washing machines manufactured by Whirlpool, Maytag, Jenn-air, and various other brands.

The Drive Belt is an OEM part for Whirlpool washing machines. This belt works to spin the washing machine tub and agitate clothes during cycles. It transmits rotational power from the motor to the inner tub and outer tub.

Causes of a bad drive belt can include wear and over time usage, exposure to harsh detergents or fabric softeners that may cause premature wear and cracking, or damage from overloading the washer.

Symptoms of a bad drive belt include:

• The washer tub not spinning or rotating very slowly
• Loud squealing, squeaking or grinding noises when operating
• The belt slipping off the pulleys
• Vibrating that causes the washer to walk or move during cycles

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Capacitor is an OEM part for Whirlpool washing machines. This part helps regulate power supply and voltage levels. It smooths out voltage fluctuations to ensure consistent operation of the motor and internal components.

Causes of a bad capacitor can include faulty wiring connections, or simply wear and tear over time. Capacitors have a limited lifespan based on usage and wear.

Symptoms of a bad capacitor include:

• The washer failing to start or not completing cycles
• Unusual noises coming from the motor area
• Fluctuating water levels and inconsistent filling
• Lights dimming when the washer is running

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

The Drive Clutch Kit is an OEM replacement part for Whirlpool washing machines. As an integral transmission component, it includes the clutch that engages the drive motor to rotate the central agitator or impeller. 

Causes of a bad clutch kit include worn parts that have aged from repeated use. Signs include slipping, grinding, or clicking noises from the transmission area.

Symptoms of a faulty clutch kit are:

• The washer tub failing to turn or agitate clothes during wash cycles  
• Delayed starts or intermittent rotation
• Vibration or shaking sensed from the frontloader or toploader

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.