Generac Pressure Washer Parts

This is an authentic carb to air cleaner gasket sourced from Generac. The gasket is placed between the air cleaner and the carburetor, and it will act as another means to reduce the amount of air that is coming into the carburetor. This is important because if there is too much air, it will affect the fuel-air mixture that is going into the carburetor. This could result in problems with the engine's performance and consistency. The carb to air cleaner gasket will start to wear out the longer it has been used. It can start to dry out and crack, and parts of it could break off entirely. This would mean more air can get into the engine. To prevent this, owners will want to make sure that they check on the gasket and replace it as needed. This should be a part of the routine maintenance of the small engine. The carb to air cleaner gasket is a genuine OEM product that is sold individually. It is designed for use in certain models of Generac small engines, such as those found in generators and gas-powered pressure washers.

A spark plug is a component within a combustion engine system that ignites the fuel/air mixture and generates a tiny explosion that is what makes power inside the engine. When the generator fails to fire and no power is generated, it is time to replace the spark plug. While an engine may start when it has bad spark plugs, it will often accelerate slowly, use fuel inefficiently, or misfire, too. This is not a difficult repair and should take no more than an hour to complete. It will require a spark plug socket wrench, ratchet, screwdrivers, and a gapping set. The spark plug has a lead that is not touching the other plug, but which is close enough to generate an arc of current and create the electricity for a spark. Be sure that the plug has the correct gap. This is an OEM replacement spark plug designed for use in Generac generators and pressure washers. This part is sold individually.

This carburetor gasket manages airflow around the motor. It is part of all carbureted engines and if it malfunctions, it allows air to be where it shouldn't. This alters the air to fuel ratio and can cause reduced performance or failure. If the gasket fails, it needs to be replaced promptly, because the engine will still run but will suffer damage if the gasket is allowed to leak air into or out of the motor. Replacing this part means taking apart the carburetor and cleaning all of the different components. It may also mean using the appropriate gasket sealer, though this varies based on the make and model of the engine or machine. This genuine OEM carburetor gasket is designed for Generac portable generators. It is shipped individually and will not include any other items, including sealants or oils.

The air cleaner gasket is placed between the air cleaner and the carburetor, which can help to ensure that the carb is getting the correct amount of air, while also providing some protection. The gasket can start to wear out eventually. It might become brittle and crack, or it might no longer sit properly, reducing its efficiency. If the air cleaner gasket has problems, it is important to replace it as soon as possible. Gaskets that are not working properly and that allow too much air to pass through could cause the engine to have trouble starting and operating. Replacing the filter is relatively simple. The air cleaner gasket is an authentic OEM part that is sold separately. This gasket is for use with power washers and generators from the Generac brand.

In gas-powered pressure or power washers, the carburetor is necessary to ensure the fuel is burning properly. The typical air to fuel ratio is between 12:1 and 15:1, and the carburetor keeps the balance where it needs to be for optimum performance levels from the equipment during use. Over time, the carburetor may clog, or the part will no longer function as it should. The signs of a failed carburetor include a poorly performing engine, smoke coming from the exhaust, overheating, backfiring, or difficulty starting the engine. In some cases, the part can be cleaned, while other times, the carburetor should be replaced.Remove the cover on the power washer with a screwdriver to replace a worn-out carburetor. Clamp the fuel line and note where the linkage is. Take off the air filter door. Remove the screws holding the carburetor. Replace with a new part and screw the carburetor back into position before removing clamps on the fuel line.This replacement carburetor is a genuine OEM part. It is sold as an individual piece. The carburetor is built of high quality, durable materials to ensure longevity. The replacement part is used in gas-powered power washers manufactured by Generac.

An alert oil unit is an important piece to prevent issues with portable generators made by Generac. The alert oil unit part is crucial to prevent the portable generator from using up all the oil without the user knowing. The purpose of the alert oil unit is to alert the machine owner or operator once the oil in the generator gets too low. The replacement or repair process of the alert oil unit should be straightforward, but always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location.This alert oil unit is essentially a safety switch that will prevent the engine of the portable generator from being ruined if it runs out of oil. This alert oil unit is an original OEM part sourced directly from the manufacturer, Generac. It is sold individually.

This is a genuine OEM recoil starter assembly sourced directly from the manufacturer. It is designed for use on pressure washers. Recoil starters are comprised of a rope, pulley, and tension spring. When the rope is pulled, the tension spring is released from the pulley, and the crankshaft spins, starting the engine. If any component in the recoil starter assembly is broken or missing, the engine will not start. Often, it is simpler and quicker to replace the whole assembly than it is to take it completely apart to replace one component. Replacement takes less than ten minutes. Before starting, remove the spark plug to ensure the engine doesn't accidentally fire up. Use a screwdriver to remove the damaged recoil start assembly. Place the new assembly on the pressure washer and install the screw. Tighten the screw until it is snug, but do not overtighten. Reinstall the spark plug. Pull the rope to verify the pull start is installed correctly.This recoil starter assembly is made of durable black molded plastic with a nylon rope starter and high tensile metal recoil spring; it is sold as an individual unit. This recoil starter assembly is specially designed for 196cc engine pressure washers manufactured by Generac.

Created for use with pressure washer by Generac, this fuel filter is an important component of the machine. A fuel filter has the responsibility of removing dirt and debris found in fuel so that it doesn't pass through to the carburetor. Having a maintained fuel filter in a pressure washer is important since even small particles could reach the carburetor. All fuel filters should be inspected on a regular basis and replaced about once a year.If the fuel filter needs to be replaced, the pressure washer should be placed on a level surface and the spark plug boot needs to be removed. Remove any fuel in the washer and then use a hooked piece of wire to pull out the fuel filter. Take the line in one hand while working to bring the filter out. Once it's out, put the new filter on the fuel line and work it inside. The filter will go into the tank and can be refilled with fuel before replacing the cap.This fuel filter is designed for use on Generac pressure washers. It is a genuine OEM product directly sourced from the manufacturer. It comes as a single individual part.

The carburetor is designed to allow airflow from the intake, through the filter, and into the engine. This keeps the fuel to air ratio in balance and allows the gas-powered generator to operate at maximum fuel efficiency. The machines will have throttles to allow adjustments to the air to fuel mix, but if the machine is not running smoothly, fails to start, or uses too much fuel, it could be that the carburetor needs replacement. This high-quality carburetor is not a difficult part to replace. This will require wrenches, sockets, and a screwdriver to make the full replacement. It includes the carburetor and adjustment valve. This is an OEM replacement part for Generac brand generators. It ships individually. It may also need the appropriate gaskets, which vary based on the model of the generator being fixed.

The way that a pressure washer works is simple, but there are also simple issues that can cause trouble with the machine. Pressure washers have both a water filter and an air filter to prevent debris from causing trouble in the machine. The air filter stops dirt and dust, as well as debris, from making it into the carburetor and causing the engine to run poorly or stall. As part of regular maintenance on a pressure washer's engine, it is a good idea to replace both the air and the oil or fuel filters. This is an OEM replacement part that will require a short amount of time and the use of a wrench set and pliers to make the change. This replacement pressure washer filter is designed to work with Generac pressure washers and effectively capture any contaminants that might enter the carburetor and then the engine itself. It works with a long list of Generac models, and is an easy part to replace.

A rollover valve is part of the evaporative emissions system and is used for lawn tractors and riding mowers. The valve allows the fuel tank to vent through a hose connected to the air filter's housing. It is also a safety feature. If a machine falls over or rolls over, it prevents fuel from leaking out. The rollover valve is made from high-quality plastic, but there is a chance it could break or wear out over time. It could also become lost. A broken or damaged rollover valve should always be replaced as soon as possible. Otherwise, a rollover could result in a dangerous leak.This valve works for certain models of tractors from Generac. This is a genuine OEM part that has been sourced from the manufacturer. It is sold individually.

This is a hose designed to be used with pressure washers by Generac. It has an M22 connection and is rated for up to 3100 PSI. The hose is used for washing automobiles, boats, and other vehicles. The water moves from the pressure washer into the hose and the stream can be directed onto the automobile to remove dirt and other debris from its surface. The hose can wear out over time or become damaged and will need to be replaced.The easiest way to determine where the hose needs to be replaced is by doing a visual inspection. Look over the hose for cracks, holes, or other damage. If the hose is starting to wear out, it will also need to be replaced. A broken or damaged hose may leak or not provide the proper water pressure. Remove the original hose and connect the new one to the equipment.This hose is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The hose is designed to be used with several pressure washers manufactured by Generac.