Parts for Ge AJCQ08ACGL1: Grille & Chassis Parts

This orifice meters gas flow to an oven burner, helping the appliance produce the correct flame for baking or broiling. Replaces a worn or clogged orifice to restore consistent burner performance. What it does:

• Controls the gas jet size to regulate burner flame size and heat output
• Helps correct symptoms like weak or uneven flame, slow oven heat-up, or burner that won't stay lit
• Prevents improper fuel-air mixture caused by a damaged or clogged orifice
• Used where precise gas flow is required for safe, efficient oven operation

• One orifice

• Shut off gas supply and unplug the appliance before servicing
• Use appropriate wrenches and avoid over-tightening to prevent damage
• Confirm correct orifice type for your fuel (natural gas vs. LP) before installation

This swing louver directs and balances airflow inside the refrigerator to help maintain even temperatures in the fresh-food compartment. It replaces a damaged or broken louver to restore adjustable airflow and proper venting. What it does

• Directs cooled air from the evaporator/fan into the fresh-food area
• Allows adjustable swing motion to spread air evenly across shelves
• Common fix for broken, cracked, or stuck louvers that limit airflow
• Helps reduce localized warm or cold spots caused by blocked vents

• One swing louver assembly

• Disconnect power to the appliance before beginning work
• Remove shelves or drawers as needed for access; handle plastic parts carefully
• Most installations snap into or slide onto the vent housing—do not force; verify alignment of tabs
• If clips are broken, replace clips or adjacent housing as needed for secure fit

This nut with attached washer is a small securing fastener used to clamp appliance parts and prevent loosening. It provides a low-profile, integrated washer bearing surface for a reliable hold. What it does:

• Secures panels, brackets, or components to prevent movement and rattling
• Maintains clamping force where an integrated washer is needed
• Helps keep electrical and mechanical connections stable
• Common symptom: loose or vibrating parts, squeaks, or components that shift during use

• One nut with attached washer

• Disconnect power and water before servicing
• Use the correct socket or wrench to avoid rounding the nut
• Tighten to snug fit — avoid overtightening which can strip threads or damage parts
• If replacing a rusted or damaged fastener, inspect mating threads and replace as needed

This flat washer provides a secure, even load distribution for a fastener on the appliance, helping maintain proper assembly and reduce loosening or wear. Use it to replace a damaged or missing washer during repairs. What it does:

• Sits under a nut or bolt to spread load and protect the appliance surface
• Helps prevent fasteners from loosening due to vibration
• Restores proper spacing and alignment for connected parts
• Commonly replaced when you see corrosion, cracking, or a loose connection

• One flat washer

• Disconnect power and turn off water supply before starting any repair
• Tighten fasteners to a snug fit—avoid over-tightening which can crush the washer
• If adjacent parts show damage or corrosion, inspect and replace as needed

Fix weak airflow or no cooling in your room air conditioner. This centrifugal fan circulates air through the unit. Common repair for most models.

Replacement washer sleeve for room air conditioners. Installs on mounting hardware to provide spacing and support. Needed when original is missing, cracked, or worn.

If your air conditioner won't blow air or runs but doesn't cool, the fan motor may have failed. This motor drives the blower fan to circulate air.

Fix weak airflow or no cooling in your room air conditioner. This fan motor replacement restores proper circulation. Moderate DIY repair in 1-2 hours.

This spring washer provides resilient tension to help keep screws and bolts from loosening on appliance assemblies. It's a simple replacement part that restores proper fastener tension and helps maintain secure connections. What it does:

• Applies spring force around a fastener to resist vibration-related loosening
• Commonly used on panels, brackets, and components that see movement or vibration
• Can reduce rattling and intermittent connection issues caused by loose hardware
• Works with 6 mm-diameter fasteners where a small lock-style washer is required

• Disconnect power and unplug the appliance before servicing
• Use the correct 6 mm fastener and proper orientation when reinstalling
• Tighten hardware to the OEM's recommended torque if available; avoid overtightening
• If other fasteners or parts are damaged, replace them to ensure a secure repair

A small mounting nut used to secure components and panels on compatible appliances. Replaces a loose or missing nut to restore stable, safe fastening and reduce rattling or wobble. What it does:

• Secures panels, brackets, or assemblies to the appliance frame
• Prevents fasteners from backing out during normal operation
• Helps stop rattling, vibration noise, and loose-fitting parts
• Restores proper alignment for attached components

• Disconnect power and water before beginning any repair
• Match threads and size before installation; hand-start the nut to avoid cross-threading
• Tighten securely with the correct socket or wrench, but do not overtighten
• If the original fastener was damaged, replace the mating bolt/stud as needed

Replacement front panel console trim for room air conditioners. Restores appearance and provides mounting surface for controls when original is cracked, faded, or broken.

Traps dust, pollen, and airborne particles to maintain clean air circulation. Replace when clogged to restore airflow and efficiency. Confirm fit with your model.