Parts for Kitchenaid KVUB600DSS2: 02 - Hood Parts

This replacement insulation panel helps reduce noise and control temperature inside the appliance cabinet for improved performance and quieter operation. It fits behind the exterior cabinet where original insulation was installed. What it does:

• Dampens operational noise and vibration to reduce overall sound levels
• Helps maintain internal temperatures by limiting heat transfer
• Protects internal components from direct heat exposure
• Restores missing or damaged insulation to improve appliance efficiency

• One insulation panel

• Remove power and disconnect the appliance before servicing
• Access the cabinet area per manufacturer service instructions to reach the insulation location
• Replace only the damaged or missing insulation; secure with factory-style adhesives or fasteners

This refrigerator cabinet insulation replaces worn or damaged thermal padding to help maintain internal temperatures and improve energy efficiency and temperature stability. It fits behind liners and panels to reduce heat transfer and dampen noise. What it does:

• Replaces torn, compressed or missing insulation that can cause poor cooling or longer run cycles
• Helps reduce frost buildup and keeps cold air inside the fresh food/freezer compartments
• Damps vibration and reduces operational noise from the compressor and fans
• Supports consistent temperatures for better food preservation

• Unplug or disconnect power before any service and work with the appliance empty and dry
• Partial disassembly of interior liners or panels may be required; keep fasteners organized
• Handle insulation with care; avoid compressing or tearing the material during installation
• Refer to your model's tech sheet or service manual for exact placement and fastening instructions

This replacement cabinet insulation restores thermal barrier inside the refrigerator, helping the appliance maintain proper cooling and reduce frost buildup. Fits the OEM cavity where original insulation has degraded or been removed. What it does:

• Replaces torn, compressed, or missing cabinet insulation that reduces cooling efficiency
• Helps prevent excessive frost buildup and long run times tied to poor insulation
• Restores proper thermal separation between refrigerated compartments and cabinet walls
• Supports consistent temperature performance and can reduce energy waste

• Always unplug the appliance or shut off power before starting work
• Remove shelves and panels as needed to access the insulation cavity; keep hardware organized
• Handle insulation gently and avoid compressing it; install in the exact orientation shown in the OEM diagram

This hood damper mounts at the exhaust outlet to let cooking air exit while blocking backdrafts when the fan is off. Replacing a worn damper restores proper airflow and helps eliminate rattling or sticking during vent operation.

• Controls one-way airflow from the hood into the duct; seals when the fan is off
• Helps block outside air and moisture from entering through the vent
• Wear or damage can cause poor venting, rattling noises, or a stuck exterior flap
• Restores vent performance after the original damper is bent, warped, or missing

• Disconnect power at the breaker before servicing
• Access the exhaust outlet and remove the old damper; note airflow orientation
• Install so the flap swings freely and seats closed; avoid overtightening fasteners
• Run the fan to verify smooth damper movement and proper airflow

Replacement transformer that provides low-voltage power to the appliance control system, restoring reliable power to the control board and display. Use when the appliance is unresponsive or shows blank/noisy controls due to a failed transformer. What it does:

• Supplies the low-voltage power required by the control board and user interface.
• Enables control panel functions, displays, and relays that rely on the transformer.
• Common symptom: blank display or no response from touch/pressed controls.
• Also may cause intermittent operation or failure of electrically-driven features when faulty.

• Disconnect power (unplug or shut off breaker) before starting any work.
• Replace with the exact part number; match to the appliance wiring and mounting.
• Observe proper wiring, polarity, and secure connections; do not work on wet surfaces.

This electronic control board replaces the main console board that manages oven/range functions, displays settings, and processes user inputs—restoring control and electronic response for affected operation. What it does

• Controls oven/range functions such as bake, broil, timers and display output.
• Processes touchpad/knob commands and sends signals to heating elements and relays.
• Addresses symptoms like a blank or flashing display, unresponsive controls, or failure to start heating cycles.
• Works with the appliance's user interface and safety interlocks to coordinate operation.

• One electronic control board.

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Handle the board by its edges and avoid static discharge; use proper ESD precautions.
• Verify wiring matches the new board and document connections before removal.
• Test the appliance after reconnecting power and before full reassembly.

The Clip is an OEM part for Whirlpool range hoods. It is a small but important component that helps securely hold portions of the range hood in place.

Symptoms of a bad clip can include wear and tear causing it to break or become loose over time, and failing to properly support attached parts. 

Causes of a bad clip include repeated opening and closing of the range hood putting stress on the clip, as well as damage from accidents.

Symptoms of a bad clip include:

• rattling or loose noises coming from the range hood 
• attached panels or pieces no longer staying fully secured
• gaps appearing where parts were formerly held tightly together

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This microwave charcoal filter captures cooking odors and smoke in recirculating setups to help keep air moving cleanly through the blower. Replace a saturated or damaged filter to maintain ventilation performance and minimize lingering smells.

• Adsorbs odors and smoke during non-vented operation
• Helps maintain airflow and keep internal surfaces cleaner
• Common signs it's due: persistent odors, reduced airflow, or a visibly dirty/damaged filter
• Intended for over-the-range microwaves that use a charcoal air filter

• Disconnect power to the microwave before servicing
• Remove the upper grille or access panel per your model; release and remove the old filter
• Install the new filter in the same orientation; reinstall grille and restore power

This control board is the go-between for the range control panel and the vital functions of the range hood. There could be several issues if the hood range's fan or a light stops working or responding to controls. When the two work intermittently or stop working in conjunction with a timer, most likely it is the hood range control board. A replacement board will need to be ordered to correct these issues. This part is designed for an oven and microwave combo with the vent and fan built-in on top.This Whirlpool range hood control board is only available individually. It is a genuine OEM product sourced directly from Whirlpool. This part is compatible with Whirlpool, KitchenAid, and JennAir.

Replacement fan motor that restores airflow by turning the appliance's circulation fan. Use this direct-fit motor to stop noisy or non-spinning fans and help maintain proper cooling, venting, or airflow in the affected compartment. What it does:

• Drives the fan/impeller to circulate air for cooling, drying, or venting.
• Common symptoms: reduced or no airflow, loud/grinding noises, or the compartment running warmer than normal.
• Direct-replacement motor designed to mount in the original fan housing and connect to existing wiring.
• Replacing a failed fan motor can stop abnormal noises and restore proper ventilation and airflow.

• Disconnect power to the appliance before beginning—unplug or switch off the circuit breaker.
• Remove the appropriate access panel and document wire locations (take a photo) before disconnecting wires.
• Handle fan blades carefully; after wiring the new motor, briefly test operation before reassembling panels.

This capacitor helps the appliance motor start and run more smoothly, restoring reliable motor operation and reducing hard-start symptoms. It's a direct-fit replacement when the original capacitor fails. What it does:

• Provides the initial electrical boost to start the motor and helps maintain stable motor operation
• Commonly replaces a failed or weak capacitor that causes the motor to hum, not start, stall, or run inconsistently
• Works with the appliance's existing control and motor components to restore normal performance
• Uses the same mounting and terminal layout as the original for a straightforward replacement

• Disconnect power to the appliance before inspecting or replacing the capacitor
• Discharge the capacitor before handling—capacitors can store a dangerous charge even when unplugged
• Take note of terminal locations or photograph wiring before removal to ensure correct reconnection

This replacement name plate is the exterior label that displays model/serial and branding information and restores the appliance's original appearance. It's a simple cosmetic part used when the original label is damaged, faded, or missing. What it does

• Replaces a worn or missing appliance identification label to restore readable model/serial and specification text
• Helps make service and parts identification easier by restoring the visible product information
• Improves exterior appearance when the factory name plate is peeling, scratched, or faded
• Provides the OEM-correct label fit and layout for a factory look

• One replacement name plate

• Surface must be clean, dry, and free of grease—use isopropyl alcohol or a mild cleaner before applying
• Peel backing and align carefully; press firmly to ensure full contact and adhesion
• Wear gloves to avoid fingerprints and handle the adhesive surface minimally
• No special tools required; remove original adhesive residue with a plastic scraper before installing

This genuine OEM replacement part is a fan motor made for refrigerators. The fan motor disperses air to the compressor and condenser parts of the refrigerator to keep them from overheating, ultimately keeping the refrigerator cool. If the refrigerator is no longer maintaining a cold temperature, this might mean that the fan motor needs to be replaced. Thankfully replacing a fan motor is a simple job.To replace the fan motor, begin by unplugging the refrigerator. Then open the freezer door and remove all bins and shelving inside the freezer. Continue by unthreading the screws on the back wall of the freezer to gain access to the motor. Remove any side screws to fully remove the back cover. Pull off the red and white power wires to the motor. Then pull off the green ground wire. With a pair of needle-nose pliers, pry off the fan blade on the top, and set it to the side. The motor is held in place by a spring bracket on the front and back; squeeze and lift up and push the motor downwards to pull it out. Install the new motor into the brackets by tilting it upward and engaging both rear and front brackets. Reinstall the wire harness and ground terminal by snapping them into their appropriate connectors. Reinstall the back cover.This genuine replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand refrigerators.

This hood damper is the exhaust vent flap that opens to let cooking smoke and steam exit and closes to help stop outside air and odors from entering when the hood fan is off. It restores proper venting and helps maintain kitchen airflow control. What it does:

• Acts as the vent flap that opens during fan operation and closes when the fan is off
• Prevents backdrafts and helps keep outside air, pests, and odors from entering the home
• A faulty or stuck damper can cause poor vent performance, reduced airflow, or rattling noises
• Replaces a worn or broken damper to restore normal hood exhaust function

• Disconnect power to the appliance before beginning work; follow all safety precautions
• Basic installation typically requires removing the hood grille or access panel to reach the damper
• Secure mounting so the flap can open and close freely
• Test fan operation after installation to ensure the damper opens and seals properly

This replacement power cord provides the electrical connection that supplies your appliance with mains power. It restores safe, reliable power delivery so your appliance can operate normally. What it does:

• Replaces a damaged or missing power cord to restore electrical connection
• Helps address symptoms like no power, intermittent power, or visible cord damage
• Maintains the appliance's grounded connection when matched to the original cord
• Routes power from the wall outlet to the appliance's inlet or terminal block

• One replacement power cord

• Disconnect power at the breaker or unplug the appliance before starting work
• Route the cord and secure strain relief/fasteners per the appliance's service instructions

This duct kit routes dryer exhaust from the appliance to the home vent, restoring proper airflow and helping the dryer operate safely and efficiently. Designed to replace damaged or missing venting components. What it does:

• Provides a secure path for hot, moist air to exit the dryer to the exterior vent
• Restores airflow to help reduce extended dry times and improve drying performance
• Helps reduce lint buildup in the cabinet and exhaust path when properly installed
• Supports safe operation by allowing heat and moisture to vent outdoors, lowering overheating risk

• One duct kit

• Disconnect power to the appliance before installing; follow local building codes for dryer venting
• Inspect and clean the vent path after installation and periodically to prevent lint buildup

This replacement grease filter captures airborne grease and cooking residue in your appliance's venting system, helping protect the blower and ductwork while maintaining effective ventilation and airflow.

• Traps grease and food particles carried by the exhaust airstream
• Helps sustain proper airflow and reduce smoke and lingering odors
• Replace if mesh is torn, warped, missing, or remains clogged after cleaning
• Common symptoms include persistent smoke/odors, visible grease buildup, or a loose/rattling filter

• Disconnect power before servicing and allow the appliance to cool completely
• Open the filter access, release the retaining latch or screws, and remove the old filter
• Slide the new filter into place, matching the original orientation/tabs
• Ensure the filter is fully seated and secured; do not operate the unit without a filter