Parts for Kitchenaid KVUB600DSS4: Hood Parts

This replacement insulation panel helps reduce noise and control temperature inside the appliance cabinet for improved performance and quieter operation. It fits behind the exterior cabinet where original insulation was installed. What it does:

• Dampens operational noise and vibration to reduce overall sound levels
• Helps maintain internal temperatures by limiting heat transfer
• Protects internal components from direct heat exposure
• Restores missing or damaged insulation to improve appliance efficiency

• One insulation panel

• Remove power and disconnect the appliance before servicing
• Access the cabinet area per manufacturer service instructions to reach the insulation location
• Replace only the damaged or missing insulation; secure with factory-style adhesives or fasteners

This refrigerator cabinet insulation replaces worn or damaged thermal padding to help maintain internal temperatures and improve energy efficiency and temperature stability. It fits behind liners and panels to reduce heat transfer and dampen noise. What it does:

• Replaces torn, compressed or missing insulation that can cause poor cooling or longer run cycles
• Helps reduce frost buildup and keeps cold air inside the fresh food/freezer compartments
• Damps vibration and reduces operational noise from the compressor and fans
• Supports consistent temperatures for better food preservation

• Unplug or disconnect power before any service and work with the appliance empty and dry
• Partial disassembly of interior liners or panels may be required; keep fasteners organized
• Handle insulation with care; avoid compressing or tearing the material during installation
• Refer to your model's tech sheet or service manual for exact placement and fastening instructions

This replacement cabinet insulation restores thermal barrier inside the refrigerator, helping the appliance maintain proper cooling and reduce frost buildup. Fits the OEM cavity where original insulation has degraded or been removed. What it does:

• Replaces torn, compressed, or missing cabinet insulation that reduces cooling efficiency
• Helps prevent excessive frost buildup and long run times tied to poor insulation
• Restores proper thermal separation between refrigerated compartments and cabinet walls
• Supports consistent temperature performance and can reduce energy waste

• Always unplug the appliance or shut off power before starting work
• Remove shelves and panels as needed to access the insulation cavity; keep hardware organized
• Handle insulation gently and avoid compressing it; install in the exact orientation shown in the OEM diagram

Replacement transformer that provides low-voltage power to the appliance control system, restoring reliable power to the control board and display. Use when the appliance is unresponsive or shows blank/noisy controls due to a failed transformer. What it does:

• Supplies the low-voltage power required by the control board and user interface.
• Enables control panel functions, displays, and relays that rely on the transformer.
• Common symptom: blank display or no response from touch/pressed controls.
• Also may cause intermittent operation or failure of electrically-driven features when faulty.

• Disconnect power (unplug or shut off breaker) before starting any work.
• Replace with the exact part number; match to the appliance wiring and mounting.
• Observe proper wiring, polarity, and secure connections; do not work on wet surfaces.

This electronic control board replaces the main console board that manages oven/range functions, displays settings, and processes user inputs—restoring control and electronic response for affected operation. What it does

• Controls oven/range functions such as bake, broil, timers and display output.
• Processes touchpad/knob commands and sends signals to heating elements and relays.
• Addresses symptoms like a blank or flashing display, unresponsive controls, or failure to start heating cycles.
• Works with the appliance's user interface and safety interlocks to coordinate operation.

• One electronic control board.

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Handle the board by its edges and avoid static discharge; use proper ESD precautions.
• Verify wiring matches the new board and document connections before removal.
• Test the appliance after reconnecting power and before full reassembly.

The Clip is an OEM part for Whirlpool range hoods. It is a small but important component that helps securely hold portions of the range hood in place.

Symptoms of a bad clip can include wear and tear causing it to break or become loose over time, and failing to properly support attached parts. 

Causes of a bad clip include repeated opening and closing of the range hood putting stress on the clip, as well as damage from accidents.

Symptoms of a bad clip include:

• rattling or loose noises coming from the range hood 
• attached panels or pieces no longer staying fully secured
• gaps appearing where parts were formerly held tightly together

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This microwave charcoal filter captures cooking odors and smoke in recirculating setups to help keep air moving cleanly through the blower. Replace a saturated or damaged filter to maintain ventilation performance and minimize lingering smells.

• Adsorbs odors and smoke during non-vented operation
• Helps maintain airflow and keep internal surfaces cleaner
• Common signs it's due: persistent odors, reduced airflow, or a visibly dirty/damaged filter
• Intended for over-the-range microwaves that use a charcoal air filter

• Disconnect power to the microwave before servicing
• Remove the upper grille or access panel per your model; release and remove the old filter
• Install the new filter in the same orientation; reinstall grille and restore power

Replacement fan motor that restores airflow by turning the appliance's circulation fan. Use this direct-fit motor to stop noisy or non-spinning fans and help maintain proper cooling, venting, or airflow in the affected compartment. What it does:

• Drives the fan/impeller to circulate air for cooling, drying, or venting.
• Common symptoms: reduced or no airflow, loud/grinding noises, or the compartment running warmer than normal.
• Direct-replacement motor designed to mount in the original fan housing and connect to existing wiring.
• Replacing a failed fan motor can stop abnormal noises and restore proper ventilation and airflow.

• Disconnect power to the appliance before beginning—unplug or switch off the circuit breaker.
• Remove the appropriate access panel and document wire locations (take a photo) before disconnecting wires.
• Handle fan blades carefully; after wiring the new motor, briefly test operation before reassembling panels.

This capacitor helps the appliance motor start and run more smoothly, restoring reliable motor operation and reducing hard-start symptoms. It's a direct-fit replacement when the original capacitor fails. What it does:

• Provides the initial electrical boost to start the motor and helps maintain stable motor operation
• Commonly replaces a failed or weak capacitor that causes the motor to hum, not start, stall, or run inconsistently
• Works with the appliance's existing control and motor components to restore normal performance
• Uses the same mounting and terminal layout as the original for a straightforward replacement

• Disconnect power to the appliance before inspecting or replacing the capacitor
• Discharge the capacitor before handling—capacitors can store a dangerous charge even when unplugged
• Take note of terminal locations or photograph wiring before removal to ensure correct reconnection

This name plate is the appliance's model and serial identification label—an easy way to restore clear product ID for service, parts ordering, and warranty records. Keeps your appliance information visible and readable. What it does:

• Displays manufacturer model and serial numbers and other factory ID details
• Restores a missing or damaged ID label so technicians can identify the correct parts and specs
• Helps when registering the appliance or filing warranty and service requests
• Prevents delays caused by unreadable or absent identification information

• Clean and dry the mounting surface before applying; remove old adhesive residue
• Align carefully and press firmly; some name plates use adhesive backing or mounting tabs
• Do not cover vents, controls, or safety labels when installing