Parts for Kenmore 795.72495610 (79572495610, 795 72495610): Ice Maker Parts

The Ice Maker Assembly Kit is an OEM part for LG refrigerators. This kit includes all the necessary components to produce ice efficiently, ensuring your refrigerator maintains a steady supply of ice for your household. The kit also features a 20-pin and 3-pin wiring harness.

Causes of a bad ice maker assembly can include wear and tear over time, mineral buildup from hard water, or electrical malfunctions. Additionally, damage can occur due to improper handling or issues with other components in the ice-making system.

Symptoms of a bad ice maker assembly include:

• No ice production
• Slow ice production or smaller ice cubes
• Ice cubes that are misshapen or irregular
• Leaking water around the ice maker
•  Unusual noises during the ice-making process

This OEM LG part is also compatible with Sears/Kenmore.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

The Ice Maker Assembly is an OEM component specifically designed for LG refrigerators. It is responsible for automatically producing batches of ice cubes on demand. 

Causes of a bad ice maker assembly can include failures in the ejector mechanism that dispenses ice, damage or leaks in the water supply components, or issues with the control board that manages the timing of each cycle. 

Symptoms of a bad ice maker assembly include:

• Failure to produce ice cubes
• Incomplete or misshapen ice cubes  
• Excessive noise during operation
• Water leaks from the ice maker area

This OEM LG replacement part is also compatible with Sears/Kenmore models. 

This lower ice bank door hinge secures and pivots the freezer's ice bank door so it opens and closes smoothly, helping maintain proper sealing and ice dispensing alignment. Designed as a direct replacement for the original hinge. What it does:

• Supports the ice bank door, providing a stable pivot point for opening and closing
• Keeps the ice bank door aligned to maintain an effective seal and proper operation
• Prevents sagging or binding that can interfere with ice dispensing or door function
• Restores correct door movement after hinge wear or damage

• Use basic hand tools; keep power to the appliance off and unplug before starting
• Handle the ice bank and door carefully to avoid damaging the trim or ice chute
• Reuse original fasteners only if undamaged; replace damaged screws to ensure secure mounting

This cover lever is a direct-fit replacement part that protects and operates the appliance's lever mechanism, restoring secure lever movement and preventing debris entry. It's a small service part that helps maintain normal door/lever function. What it does:

• Covers and protects the lever assembly from wear and debris
• Provides the proper surface for the lever to engage and operate smoothly
• Replaces cracked, broken, or missing lever covers that can catch or stick
• Helps restore proper user control when lever trim is damaged

• One cover lever (single piece)

• Disconnect power before performing any service
• Installation is typically a panel-level repair; remove access panel or trim to reach the lever area
• May snap or screw into place; keep fasteners and alignment tabs in mind during reassembly

This ice bank door gasket is the flexible door seal that keeps the ice bin compartment closed to limit warm air and moisture intrusion. Replacing a worn or torn gasket restores a tighter seal and helps reduce frost buildup and ice clumping. What it does:

• Forms an airtight seal around the ice bank/ice bin door to help prevent warm air and moisture from entering the compartment
• Reduces frost buildup, ice clumping, and excessive condensation inside the ice bin area
• Helps stop water or drips that can occur when the door seal is cracked or deformed
• Restores even door contact for proper closing and retention of ice quality

• Disconnect power to the refrigerator and remove the ice bin and any loose items before beginning.
• Inspect the door mounting channel; clean residue and old adhesive so the new gasket seats fully.
• Press the gasket evenly into the door channel, aligning any tabs or locator features; avoid stretching the gasket excessively.
• Use only non-sharp tools to ease the gasket into place; if the model uses clips or adhesive, replace or reapply per the manufacturer's instructions.

This door gasket seals the refrigerator door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a tight seal for proper cooling and helps reduce frost and condensation around the door opening. What it does:

• Forms an airtight seal between the door and cabinet frame
• Helps maintain stable internal temperature and humidity
• Helps prevent frost, icing, and condensation near the door
• Helps with symptoms like visible tears, gaps, poor door sealing, or warm spots/frost near the gasket

• 1 refrigerator door gasket

• Disconnect power before servicing
• Warm the new gasket (soak in warm water or gently heat) to improve flexibility
• Remove the old gasket and clean the mounting groove/sealing surface
• Press the new gasket fully into the groove/retainer; adjust door alignment if needed

The Ice Door Handle is an OEM replacement part for LG refrigerators. It allows users to easily access ice and water from the external ice/water dispenser. Handles experience substantial daily use as people frequently obtain water/ice. Over the years, plastic hinges can degrade from repeated opening/closing stresses.

Causes include fatigue cracks along hinge points from perpetual flexing. General wear and tear as well as occasional impacts also deteriorate structure.

Symptoms of a bad ice door handle include:

• Loose, wobbly, or dysfunctional opening/closing capability
• Cracks around mounting brackets compromise integrity
• Detached handle pieces preventing access to ice/water dispenser
• Excessive opening force required or inability to fully open/close

This OEM LG replacement is also compatible with select Sears/Kenmore refrigerators.

The Ice Door Handle Roller is an OEM replacement part for LG and some Kenmore refrigerators. Each handle contains two rollers and they help the handle move smoothly and prevent any unnecessary wear and tear. Please note, this is for one (1) door handle roller. It is recommended to replace both at the same time. 

Symptoms of a bad Ice Door Handle Roller include:

• Difficulty in dispensing ice, with the chute door sticking or not opening properly.
• Noises such as squeaking or grinding when the ice door is activated.
• Increased effort needed to operate the ice dispenser handle.
• Visible wear or damage to the roller, affecting its movement.

Causes of a bad ice door handle roller can include mechanical wear from regular use, debris accumulation that impedes the roller’s movement, or damage from excessive force used on the dispenser handle.

This OEM LG part is also compatible with Sears/Kenmore models.