Parts for Frigidaire FRSS26L3AF2: Ice & Water Dispenser Parts

This replacement tube routes refrigerant-cycle condensate and defrost water away from the evaporator area to the drain pan, helping stop pooling and prevent leaks that can damage cabinets or cause odor. Easy direct-replacement when the original tube is cracked or clogged. What it does

• Channels defrost and condensate water from the evaporator area to the drain pan.
• Helps prevent water pooling inside the fresh food or freezer section.
• Reduces risk of leaks that can cause floor damage or moldy odors.
• Can restore proper defrost drainage when the original tube is crushed, cracked, or blocked.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• If applicable, turn off the water supply and drain any residual water before removing connections.
• Inspect surrounding seals and grommets; replace if worn to ensure a watertight fit.
• After installation, run a short cycle or pour a small amount of water into the evaporator area to ensure proper drainage.

This electronic control board is the appliance's central "brain." It governs power to components, interprets inputs, and coordinates timing so selected functions run reliably and status is shown correctly.

• Coordinates signals from sensors and the user interface to execute programmed cycles
• Switches power to components through onboard relays
• Regulates timing and, where applicable, temperature or cycle parameters
• Typical failure symptoms: dead or erratic display, unresponsive buttons, failure to start, or recurring error codes

• Disconnect power at the breaker or unplug the unit before servicing
• Use ESD protection and handle the board by the edges
• Photograph wiring and move connectors one at a time to the same positions on the new board
• Mount securely and follow your model's tech sheet for wiring verification and post-install checks

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This water inlet tube routes potable water from the refrigerator's inlet/valve to the dispenser and ice-making components, helping restore normal water delivery and prevent leaks when damaged. What it does

• Channels water from the inlet valve to the dispenser/ice maker assembly.
• Replaces cracked, kinked, or clogged tubing that can cause leaks or reduced flow.
• Helps stop visible dripping, puddling, or intermittent water flow at the dispenser.
• Works as a direct-fit plumbing replacement when the original tube is damaged.

• One water inlet tube

• Turn off refrigerator power and shut off the water supply before starting.
• Inspect fittings and seals; replace any damaged ferrules or gaskets for a watertight connection.
• Use basic hand tools; avoid sharp bends or kinks when routing the tube.
• After installation, restore water and power, then check all connections for leaks.

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle