Parts for Lg LDG3015ST: Lower Cavity Parts

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This customized screw is the exact fastener specified by the manufacturer to secure components in select LG appliances. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps maintain proper alignment over time.

• Secures panels, brackets, and internal assemblies at original mounting points
• Helps reduce vibration and rattling noises from loose hardware
• Replaces missing, rusted, or stripped screws
• Supports stable operation by keeping parts firmly in place

• Disconnect power; shut off water or gas before service
• Match the screw to the exact location using your model's parts diagram
• Start threads by hand; tighten snugly without overtightening to avoid stripping
• Use the correct driver bit for the head style to prevent damage

The Oven Rack is an OEM part for LG ranges. This part provides a stable surface for placing cookware during baking, roasting, and broiling.

Causes of a bad oven rack can include exposure to high temperatures over time, which can weaken the metal, or accidental damage that causes bending or warping.  

Symptoms of a bad oven rack include:

• Warping or bending of the rack
• Difficulty sliding the rack in and out of the oven
• The rack not sitting level within the oven

This OEM LG part is also compatible with some Kenmore models.

This vent cover is the exterior trim piece that finishes and protects the appliance vent opening, helping direct airflow and keeping lint and debris out of the vent cavity. It restores a clean, finished look and proper airflow. What it does

• Covers and seals the vent opening to help direct exhaust airflow and reduce drafts
• Protects internal components from lint, dust and small debris entering the vent path
• Helps reduce rattling or vibration caused by a damaged or loose vent trim
• Wear or cracks can cause poor airflow, noise, or visible gaps at the vent opening

• Remove power and disconnect the appliance from its power source before starting any work
• Installation is typically simple: remove retaining screws or clips, replace cover, and secure with the original fasteners
• Handle gently to avoid cracking plastic trim; align tabs and screw locations before tightening

This door gasket is a molded seal that replaces a worn or damaged refrigerator door seal to restore an airtight closure and help maintain proper cooling. It fits on the cabinet door edge to keep cold air in and warm air out. What it does:

• Creates a tight seal around the refrigerator/freezer door to prevent air leaks
• Helps stop frost buildup and uneven temperatures caused by a failing seal
• Reduces cycling frequency and helps the appliance maintain set temperatures
• Common symptoms: visible cracks, gaps, tears, loose edges, interior condensation or frost near the door

• Remove the old gasket completely and clean the mounting surface before installing
• Start installation at the corners, working the gasket evenly into the channel for a uniform fit
• Check alignment and compression around the full perimeter; trim only if the gasket is explicitly manufactured to be shortened
• Follow appliance safety: unplug or disconnect power before beginning work and avoid sharp tools that can tear the new seal

Note: This is a quantity of 1 orifice.

This inlet valve controls water flow into the appliance, restoring proper fill operation and cycle performance. Replaces a failed or leaking valve to stop slow fills, no-fill conditions, or continuous water flow. What it does:

• Opens and closes to allow water into the appliance during fill cycles
• Stops water flow when the fill is complete to prevent overfilling
• Commonly used to address slow fills, no water entering the appliance, or water leaking from the valve area
• Works with the appliance's control system to time and meter water intake

• Disconnect power and shut off the water supply before starting work
• Verify the replacement valve matches the original part number and inlet/outlet fittings
• Use basic hand tools; avoid overtightening fittings to prevent damage

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening