Parts for Ge AZ45E12DACW6: Motor & Chassis Parts

Plastic coupler that connects shroud sections on your room air conditioner. Replace if cracked, broken, or missing to secure the outer cabinet.

This replacement fan shroud clip fastens the outer fan shroud to the appliance frame, helping keep the fan assembly secure and aligned for proper airflow. It's a small but necessary part for stable fan operation. What it does

• Secures the outer fan shroud to the dryer/refrigerator cabinet to hold the fan assembly in position
• Helps prevent fan wobble and rubbing that can cause noise or premature wear
• Maintains proper airflow path for cooling or exhaust systems
• Useful when an original clip is cracked, bent or missing

• One fan shroud clip

• Disconnect power (and gas, if applicable) before beginning any repair
• Access may require removing a rear or lower panel; keep track of fasteners and orientation
• Inspect surrounding shroud and fan for damage while replacing the clip

Fix rattling noise or sluggish fan operation in your room air conditioner with this DC fan motor. Direct replacement for improved efficiency and quiet.

5/16" shoulder screw secures panels and internal components in room air conditioners. Replace if rusted, corroded, stripped, or missing threads.

Replacement 10-32 hex nut for room air conditioner assemblies. Secures panels, brackets, and components. Needed when original nut is lost or stripped.

AC not cooling or overheating? This outdoor fan assembly circulates air across the condenser coil to expel heat and restore proper cooling performance.

Air conditioner won't heat or fan speed stuck? This silicon controlled rectifier regulates power output to restore proper voltage control and operation.

This U-nut secures panels and trim to sheet-metal flanges and studs, providing a threaded attachment point for screws on 10–16 gauge material. It helps restore solid, rattle-free connections and reliable fastener engagement. What it does:

• Provides a captive, threaded insert for machine or sheet-metal screws on thin metal flanges
• Restores or replaces stripped, missing, or damaged panel mounting points
• Helps stop loose panels, vibration noise, and misaligned trim caused by missing fasteners
• Designed for use where a 10–16 screw size and hi/lo flange thickness is required

• Verify correct location and flange thickness before installing; part is sized for 10–16 fasteners and hi/lo flange profiles
• Slide onto flange or stud until fully seated, then fasten with the specified screw; avoid forcing or deforming the clip
• Use hand tools and proper screw size; do not overtighten to prevent stripping the nut or damaging the panel
• Disconnect power and follow manufacturer service instructions when accessing internal appliance areas

This bulkhead wire cover protects and organizes the appliance's wire harness where it passes through the bulkhead, helping prevent abrasion and electrical shorts. It's a simple replacement that restores proper wire routing and protection. What it does:

• Shields wiring at the bulkhead from chafing and contact with sharp edges
• Keeps the harness routed and secured to reduce strain on wire connections
• Helps prevent intermittent electrical faults, arcing, or burning smells from damaged insulation
• Restores the intended factory wire protection after impact or wear

• Disconnect power to the appliance before starting any work to avoid shock or injury
• Remove the necessary panels to access the bulkhead and wiring harness; handle connectors gently
• Slide or clip the cover into position over the harness and verify routing matches the factory path
• Inspect adjacent wiring and terminals; replace any damaged wires or connectors as needed

This indoor motor mount secures the appliance motor to the housing to reduce vibration and keep the motor aligned for reliable operation. It's a simple replacement that helps restore quiet, stable motor performance. What it does:

• Holds the motor in the correct position to prevent shifting and rubbing
• Dampens motor vibration to reduce noise and rattling during operation
• Helps maintain proper alignment for attached fan blades or drive components
• Can stop symptoms like unusual motor noise, excessive vibration, or intermittent contact

• One indoor motor mount

• Disconnect power to the appliance before starting any repair
• Support the motor while removing and installing the mount to avoid strain on wiring
• Use basic hand tools; tighten fasteners to secure but do not overtighten

Air conditioner not blowing air or making unusual noises? This indoor fan motor kit circulates air throughout your room. Connects via plug-in harness.

AC not cooling or no airflow? The indoor fan blade circulates cooled air into your room. Simple DIY replacement—unplug, remove front panel and cover.

Right-side end cap for room air conditioners. Covers and protects the outer edge trim, restoring clean appearance after original becomes cracked or broken.

Supports and centers the blower shaft in your room air conditioner's indoor fan assembly. Replace when you notice excessive noise or vibration. Confirm fit with your model number before ordering.

Fix an air conditioner that won't heat with a new heater assembly. Common cause when unit switches to heat mode but produces no warm air.

This 11-piece wall sleeve gasket kit provides replacement foam seals that help restore a snug seal around the dryer vent wall sleeve, reducing drafts, rattles and moisture infiltration for better performance and quieter operation. What it does:

• Replaces worn or missing foam gasket pieces around the wall sleeve to improve the seal between the dryer vent and the wall.
• Helps reduce air leaks and drafts that can lower dryer efficiency or bring cold air into the home.
• Cushions the sleeve to reduce vibration and rattling during operation.
• Minimizes gaps that can allow lint, dust or small pests into the wall cavity.

• Disconnect power and ensure the dryer and vent are cool before beginning work.
• Remove the dryer and wall sleeve trim as needed, clean mating surfaces, and confirm correct placement of each gasket piece.
• Use only manufacturer-recommended fasteners or adhesive if required; verify orientation and fit before final reassembly.